bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

🚸 More flexible Probe Temperature Compensation (#23033)

Browse Source
This commit is contained in:
tombrazier 2021-11-01 23:03:50 +00:00 committed by Scott Lahteine
parent efd9329c81
commit 0b84194127
15 changed files with 672 additions and 623 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

100
Marlin/Configuration_adv.h
View File

@ -1988,65 +1988,69 @@
/** /**
* Thermal Probe Compensation * Thermal Probe Compensation
* Probe measurements are adjusted to compensate for temperature distortion. *
* Use G76 to calibrate this feature. Use M871 to set values manually. * Adjust probe measurements to compensate for distortion associated with the temperature
* For a more detailed explanation of the process see G76_M871.cpp. * of the probe, bed, and/or hotend.
* Use G76 to automatically calibrate this feature for probe and bed temperatures.
* (Extruder temperature/offset values must be calibrated manually.)
* Use M871 to set temperature/offset values manually.
* For more details see https://marlinfw.org/docs/features/probe_temp_compensation.html
*/ */
#if HAS_BED_PROBE && TEMP_SENSOR_PROBE && TEMP_SENSOR_BED //#define PTC_PROBE // Compensate based on probe temperature
// Enable thermal first layer compensation using bed and probe temperatures //#define PTC_BED // Compensate based on bed temperature
#define PROBE_TEMP_COMPENSATION //#define PTC_HOTEND // Compensate based on hotend temperature
// Add additional compensation depending on hotend temperature #if ANY(PTC_PROBE, PTC_BED, PTC_HOTEND)
// Note: this values cannot be calibrated and have to be set manually /**
#if ENABLED(PROBE_TEMP_COMPENSATION) * If the probe is outside the defined range, use linear extrapolation with the closest
* point and the point with index PTC_LINEAR_EXTRAPOLATION. e.g., If set to 4 it will use the
* linear extrapolation between data[0] and data[4] for values below PTC_PROBE_START.
*/
//#define PTC_LINEAR_EXTRAPOLATION 4
#if ENABLED(PTC_PROBE)
// Probe temperature calibration generates a table of values starting at PTC_PROBE_START
// (e.g., 30), in steps of PTC_PROBE_RES (e.g., 5) with PTC_PROBE_COUNT (e.g., 10) samples.
#define PTC_PROBE_START 30 // (°C)
#define PTC_PROBE_RES 5 // (°C)
#define PTC_PROBE_COUNT 10
#define PTC_PROBE_ZOFFS { 0 } // (µm) Z adjustments per sample
#endif
#if ENABLED(PTC_BED)
// Bed temperature calibration builds a similar table.
#define PTC_BED_START 60 // (°C)
#define PTC_BED_RES 5 // (°C)
#define PTC_BED_COUNT 10
#define PTC_BED_ZOFFS { 0 } // (µm) Z adjustments per sample
#endif
#if ENABLED(PTC_HOTEND)
// Note: There is no automatic calibration for the hotend. Use M871.
#define PTC_HOTEND_START 180 // (°C)
#define PTC_HOTEND_RES 5 // (°C)
#define PTC_HOTEND_COUNT 20
#define PTC_HOTEND_ZOFFS { 0 } // (µm) Z adjustments per sample
#endif
// G76 options
#if BOTH(PTC_PROBE, PTC_BED)
// Park position to wait for probe cooldown // Park position to wait for probe cooldown
#define PTC_PARK_POS { 0, 0, 100 } #define PTC_PARK_POS { 0, 0, 100 }
// Probe position to probe and wait for probe to reach target temperature // Probe position to probe and wait for probe to reach target temperature
//#define PTC_PROBE_POS { 12.0f, 7.3f } // Example: MK52 magnetic heatbed
#define PTC_PROBE_POS { 90, 100 } #define PTC_PROBE_POS { 90, 100 }
// Enable additional compensation using hotend temperature // The temperature the probe should be at while taking measurements during
// Note: this values cannot be calibrated automatically but have to be set manually via M871. // bed temperature calibration.
//#define USE_TEMP_EXT_COMPENSATION #define PTC_PROBE_TEMP 30 // (°C)
// Probe temperature calibration generates a table of values starting at PTC_SAMPLE_START
// (e.g., 30), in steps of PTC_SAMPLE_RES (e.g., 5) with PTC_SAMPLE_COUNT (e.g., 10) samples.
//#define PTC_SAMPLE_START 30 // (°C)
//#define PTC_SAMPLE_RES 5 // (°C)
//#define PTC_SAMPLE_COUNT 10
// Bed temperature calibration builds a similar table.
//#define BTC_SAMPLE_START 60 // (°C)
//#define BTC_SAMPLE_RES 5 // (°C)
//#define BTC_SAMPLE_COUNT 10
#if ENABLED(USE_TEMP_EXT_COMPENSATION)
//#define ETC_SAMPLE_START 180 // (°C)
//#define ETC_SAMPLE_RES 5 // (°C)
//#define ETC_SAMPLE_COUNT 20
#endif
// The temperature the probe should be at while taking measurements during bed temperature
// calibration.
//#define BTC_PROBE_TEMP 30 // (°C)
// Height above Z=0.0 to raise the nozzle. Lowering this can help the probe to heat faster. // Height above Z=0.0 to raise the nozzle. Lowering this can help the probe to heat faster.
// Note: the Z=0.0 offset is determined by the probe offset which can be set using M851. // Note: The Z=0.0 offset is determined by the probe Z offset (e.g., as set with M851 Z).
//#define PTC_PROBE_HEATING_OFFSET 0.5 #define PTC_PROBE_HEATING_OFFSET 0.5
// Height to raise the Z-probe between heating and taking the next measurement. Some probes
// may fail to untrigger if they have been triggered for a long time, which can be solved by
// increasing the height the probe is raised to.
//#define PTC_PROBE_RAISE 15
// If the probe is outside of the defined range, use linear extrapolation using the closest
// point and the PTC_LINEAR_EXTRAPOLATION'th next point. E.g. if set to 4 it will use data[0]
// and data[4] to perform linear extrapolation for values below PTC_SAMPLE_START.
//#define PTC_LINEAR_EXTRAPOLATION 4
#endif #endif
#endif #endif // PTC_PROBE || PTC_BED || PTC_HOTEND
// @section extras // @section extras

84
Marlin/src/feature/probe_temp_comp.cpp
View File

@ -22,39 +22,53 @@
#include "../inc/MarlinConfigPre.h" #include "../inc/MarlinConfigPre.h"
#if ENABLED(PROBE_TEMP_COMPENSATION) #if HAS_PTC
//#define DEBUG_PTC // Print extra debug output with 'M871' //#define DEBUG_PTC // Print extra debug output with 'M871'
#include "probe_temp_comp.h" #include "probe_temp_comp.h"
#include <math.h> #include <math.h>
ProbeTempComp temp_comp; ProbeTempComp ptc;
int16_t ProbeTempComp::z_offsets_probe[cali_info_init[TSI_PROBE].measurements], // = {0} #if ENABLED(PTC_PROBE)
ProbeTempComp::z_offsets_bed[cali_info_init[TSI_BED].measurements]; // = {0} constexpr int16_t z_offsets_probe_default[PTC_PROBE_COUNT] = PTC_PROBE_ZOFFS;
int16_t ProbeTempComp::z_offsets_probe[PTC_PROBE_COUNT] = PTC_PROBE_ZOFFS;
#endif
#if ENABLED(USE_TEMP_EXT_COMPENSATION) #if ENABLED(PTC_BED)
int16_t ProbeTempComp::z_offsets_ext[cali_info_init[TSI_EXT].measurements]; // = {0} constexpr int16_t z_offsets_bed_default[PTC_BED_COUNT] = PTC_BED_ZOFFS;
int16_t ProbeTempComp::z_offsets_bed[PTC_BED_COUNT] = PTC_BED_ZOFFS;
#endif
#if ENABLED(PTC_HOTEND)
constexpr int16_t z_offsets_hotend_default[PTC_HOTEND_COUNT] = PTC_HOTEND_ZOFFS;
int16_t ProbeTempComp::z_offsets_hotend[PTC_HOTEND_COUNT] = PTC_HOTEND_ZOFFS;
#endif #endif
int16_t *ProbeTempComp::sensor_z_offsets[TSI_COUNT] = { int16_t *ProbeTempComp::sensor_z_offsets[TSI_COUNT] = {
ProbeTempComp::z_offsets_probe, ProbeTempComp::z_offsets_bed #if ENABLED(PTC_PROBE)
OPTARG(USE_TEMP_EXT_COMPENSATION, ProbeTempComp::z_offsets_ext) ProbeTempComp::z_offsets_probe,
#endif
#if ENABLED(PTC_BED)
ProbeTempComp::z_offsets_bed,
#endif
#if ENABLED(PTC_HOTEND)
ProbeTempComp::z_offsets_hotend,
#endif
}; };
const temp_calib_t ProbeTempComp::cali_info[TSI_COUNT] = { constexpr temp_calib_t ProbeTempComp::cali_info[TSI_COUNT];
cali_info_init[TSI_PROBE], cali_info_init[TSI_BED]
OPTARG(USE_TEMP_EXT_COMPENSATION, cali_info_init[TSI_EXT])
};
constexpr xyz_pos_t ProbeTempComp::park_point;
constexpr xy_pos_t ProbeTempComp::measure_point;
constexpr celsius_t ProbeTempComp::probe_calib_bed_temp;
uint8_t ProbeTempComp::calib_idx; // = 0 uint8_t ProbeTempComp::calib_idx; // = 0
float ProbeTempComp::init_measurement; // = 0.0 float ProbeTempComp::init_measurement; // = 0.0
void ProbeTempComp::reset() {
TERN_(PTC_PROBE, LOOP_L_N(i, PTC_PROBE_COUNT) z_offsets_probe[i] = z_offsets_probe_default[i]);
TERN_(PTC_BED, LOOP_L_N(i, PTC_BED_COUNT) z_offsets_bed[i] = z_offsets_bed_default[i]);
TERN_(PTC_HOTEND, LOOP_L_N(i, PTC_HOTEND_COUNT) z_offsets_hotend[i] = z_offsets_hotend_default[i]);
}
void ProbeTempComp::clear_offsets(const TempSensorID tsi) { void ProbeTempComp::clear_offsets(const TempSensorID tsi) {
LOOP_L_N(i, cali_info[tsi].measurements) LOOP_L_N(i, cali_info[tsi].measurements)
sensor_z_offsets[tsi][i] = 0; sensor_z_offsets[tsi][i] = 0;
@ -71,10 +85,9 @@ void ProbeTempComp::print_offsets() {
LOOP_L_N(s, TSI_COUNT) { LOOP_L_N(s, TSI_COUNT) {
celsius_t temp = cali_info[s].start_temp; celsius_t temp = cali_info[s].start_temp;
for (int16_t i = -1; i < cali_info[s].measurements; ++i) { for (int16_t i = -1; i < cali_info[s].measurements; ++i) {
SERIAL_ECHOF(s == TSI_BED ? F("Bed") : SERIAL_ECHOF(
#if ENABLED(USE_TEMP_EXT_COMPENSATION) TERN_(PTC_BED, s == TSI_BED ? F("Bed") :)
s == TSI_EXT ? F("Extruder") : TERN_(PTC_HOTEND, s == TSI_EXT ? F("Extruder") :)
#endif
F("Probe") F("Probe")
); );
SERIAL_ECHOLNPGM( SERIAL_ECHOLNPGM(
@ -100,21 +113,13 @@ void ProbeTempComp::prepare_new_calibration(const_float_t init_meas_z) {
} }
void ProbeTempComp::push_back_new_measurement(const TempSensorID tsi, const_float_t meas_z) { void ProbeTempComp::push_back_new_measurement(const TempSensorID tsi, const_float_t meas_z) {
switch (tsi) {
case TSI_PROBE:
case TSI_BED:
//case TSI_EXT:
if (calib_idx >= cali_info[tsi].measurements) return; if (calib_idx >= cali_info[tsi].measurements) return;
sensor_z_offsets[tsi][calib_idx++] = static_cast<int16_t>(meas_z * 1000.0f - init_measurement * 1000.0f); sensor_z_offsets[tsi][calib_idx++] = static_cast<int16_t>((meas_z - init_measurement) * 1000.0f);
default: break;
}
} }
bool ProbeTempComp::finish_calibration(const TempSensorID tsi) { bool ProbeTempComp::finish_calibration(const TempSensorID tsi) {
if (tsi != TSI_PROBE && tsi != TSI_BED) return false; if (!calib_idx) {
SERIAL_ECHOLNPGM("!No measurements.");
if (calib_idx < 3) {
SERIAL_ECHOLNPGM("!Insufficient measurements (min. 3).");
clear_offsets(tsi); clear_offsets(tsi);
return false; return false;
} }
@ -130,16 +135,15 @@ bool ProbeTempComp::finish_calibration(const TempSensorID tsi) {
SERIAL_ECHOLNPGM("Got ", calib_idx, " measurements. "); SERIAL_ECHOLNPGM("Got ", calib_idx, " measurements. ");
if (linear_regression(tsi, k, d)) { if (linear_regression(tsi, k, d)) {
SERIAL_ECHOPGM("Applying linear extrapolation"); SERIAL_ECHOPGM("Applying linear extrapolation");
calib_idx--;
for (; calib_idx < measurements; ++calib_idx) { for (; calib_idx < measurements; ++calib_idx) {
const celsius_float_t temp = start_temp + float(calib_idx) * res_temp; const celsius_float_t temp = start_temp + float(calib_idx + 1) * res_temp;
data[calib_idx] = static_cast<int16_t>(k * temp + d); data[calib_idx] = static_cast<int16_t>(k * temp + d);
} }
} }
else { else {
// Simply use the last measured value for higher temperatures // Simply use the last measured value for higher temperatures
SERIAL_ECHOPGM("Failed to extrapolate"); SERIAL_ECHOPGM("Failed to extrapolate");
const int16_t last_val = data[calib_idx]; const int16_t last_val = data[calib_idx-1];
for (; calib_idx < measurements; ++calib_idx) for (; calib_idx < measurements; ++calib_idx)
data[calib_idx] = last_val; data[calib_idx] = last_val;
} }
@ -157,7 +161,7 @@ bool ProbeTempComp::finish_calibration(const TempSensorID tsi) {
// Restrict the max. offset difference between two probings // Restrict the max. offset difference between two probings
if (calib_idx > 0 && ABS(data[calib_idx - 1] - data[calib_idx]) > 800) { if (calib_idx > 0 && ABS(data[calib_idx - 1] - data[calib_idx]) > 800) {
SERIAL_ECHOLNPGM("!Invalid Z-offset between two probings detected (0-0.8)."); SERIAL_ECHOLNPGM("!Invalid Z-offset between two probings detected (0-0.8).");
clear_offsets(TSI_PROBE); clear_offsets(tsi);
return false; return false;
} }
} }
@ -168,8 +172,8 @@ bool ProbeTempComp::finish_calibration(const TempSensorID tsi) {
void ProbeTempComp::compensate_measurement(const TempSensorID tsi, const celsius_t temp, float &meas_z) { void ProbeTempComp::compensate_measurement(const TempSensorID tsi, const celsius_t temp, float &meas_z) {
const uint8_t measurements = cali_info[tsi].measurements; const uint8_t measurements = cali_info[tsi].measurements;
const celsius_t start_temp = cali_info[tsi].start_temp, const celsius_t start_temp = cali_info[tsi].start_temp,
end_temp = cali_info[tsi].end_temp, res_temp = cali_info[tsi].temp_resolution,
res_temp = cali_info[tsi].temp_resolution; end_temp = start_temp + measurements * res_temp;
const int16_t * const data = sensor_z_offsets[tsi]; const int16_t * const data = sensor_z_offsets[tsi];
// Given a data index, return { celsius, zoffset } in the form { x, y } // Given a data index, return { celsius, zoffset } in the form { x, y }
@ -208,9 +212,7 @@ void ProbeTempComp::compensate_measurement(const TempSensorID tsi, const celsius
} }
bool ProbeTempComp::linear_regression(const TempSensorID tsi, float &k, float &d) { bool ProbeTempComp::linear_regression(const TempSensorID tsi, float &k, float &d) {
if (tsi != TSI_PROBE && tsi != TSI_BED) return false; if (!WITHIN(calib_idx, 1, cali_info[tsi].measurements)) return false;
if (!WITHIN(calib_idx, 2, cali_info[tsi].measurements)) return false;
const celsius_t start_temp = cali_info[tsi].start_temp, const celsius_t start_temp = cali_info[tsi].start_temp,
res_temp = cali_info[tsi].temp_resolution; res_temp = cali_info[tsi].temp_resolution;
@ -243,4 +245,4 @@ bool ProbeTempComp::linear_regression(const TempSensorID tsi, float &k, float &d
return true; return true;
} }
#endif // PROBE_TEMP_COMPENSATION #endif // HAS_PTC

112
Marlin/src/feature/probe_temp_comp.h
View File

@ -24,9 +24,13 @@
#include "../inc/MarlinConfig.h" #include "../inc/MarlinConfig.h"
enum TempSensorID : uint8_t { enum TempSensorID : uint8_t {
#if ENABLED(PTC_PROBE)
TSI_PROBE, TSI_PROBE,
#endif
#if ENABLED(PTC_BED)
TSI_BED, TSI_BED,
#if ENABLED(USE_TEMP_EXT_COMPENSATION) #endif
#if ENABLED(PTC_HOTEND)
TSI_EXT, TSI_EXT,
#endif #endif
TSI_COUNT TSI_COUNT
@ -35,8 +39,7 @@ enum TempSensorID : uint8_t {
typedef struct { typedef struct {
uint8_t measurements; // Max. number of measurements to be stored (35 - 80°C) uint8_t measurements; // Max. number of measurements to be stored (35 - 80°C)
celsius_t temp_resolution, // Resolution in °C between measurements celsius_t temp_resolution, // Resolution in °C between measurements
start_temp, // Base measurement; z-offset == 0 start_temp; // Base measurement; z-offset == 0
end_temp;
} temp_calib_t; } temp_calib_t;
/** /**
@ -45,93 +48,40 @@ typedef struct {
* measurement errors/shifts due to changed temperature. * measurement errors/shifts due to changed temperature.
*/ */
// Probe temperature calibration constants
#ifndef PTC_SAMPLE_COUNT
#define PTC_SAMPLE_COUNT 10
#endif
#ifndef PTC_SAMPLE_RES
#define PTC_SAMPLE_RES 5
#endif
#ifndef PTC_SAMPLE_START
#define PTC_SAMPLE_START 30
#endif
#define PTC_SAMPLE_END (PTC_SAMPLE_START + (PTC_SAMPLE_COUNT) * PTC_SAMPLE_RES)
// Bed temperature calibration constants
#ifndef BTC_PROBE_TEMP
#define BTC_PROBE_TEMP 30
#endif
#ifndef BTC_SAMPLE_COUNT
#define BTC_SAMPLE_COUNT 10
#endif
#ifndef BTC_SAMPLE_RES
#define BTC_SAMPLE_RES 5
#endif
#ifndef BTC_SAMPLE_START
#define BTC_SAMPLE_START 60
#endif
#define BTC_SAMPLE_END (BTC_SAMPLE_START + (BTC_SAMPLE_COUNT) * BTC_SAMPLE_RES)
// Extruder temperature calibration constants
#if ENABLED(USE_TEMP_EXT_COMPENSATION)
#ifndef ETC_SAMPLE_COUNT
#define ETC_SAMPLE_COUNT 20
#endif
#ifndef ETC_SAMPLE_RES
#define ETC_SAMPLE_RES 5
#endif
#ifndef ETC_SAMPLE_START
#define ETC_SAMPLE_START 180
#endif
#define ETC_SAMPLE_END (ETC_SAMPLE_START + (ETC_SAMPLE_COUNT) * ETC_SAMPLE_RES)
#endif
#ifndef PTC_PROBE_HEATING_OFFSET
#define PTC_PROBE_HEATING_OFFSET 0.5f
#endif
#ifndef PTC_PROBE_RAISE
#define PTC_PROBE_RAISE 10
#endif
static constexpr temp_calib_t cali_info_init[TSI_COUNT] = {
{ PTC_SAMPLE_COUNT, PTC_SAMPLE_RES, PTC_SAMPLE_START, PTC_SAMPLE_END }, // Probe
{ BTC_SAMPLE_COUNT, BTC_SAMPLE_RES, BTC_SAMPLE_START, BTC_SAMPLE_END }, // Bed
#if ENABLED(USE_TEMP_EXT_COMPENSATION)
{ ETC_SAMPLE_COUNT, ETC_SAMPLE_RES, ETC_SAMPLE_START, ETC_SAMPLE_END }, // Extruder
#endif
};
class ProbeTempComp { class ProbeTempComp {
public: public:
static const temp_calib_t cali_info[TSI_COUNT]; static constexpr temp_calib_t cali_info[TSI_COUNT] = {
#if ENABLED(PTC_PROBE)
{ PTC_PROBE_COUNT, PTC_PROBE_RES, PTC_PROBE_START }, // Probe
#endif
#if ENABLED(PTC_BED)
{ PTC_BED_COUNT, PTC_BED_RES, PTC_BED_START }, // Bed
#endif
#if ENABLED(PTC_HOTEND)
{ PTC_HOTEND_COUNT, PTC_HOTEND_RES, PTC_HOTEND_START }, // Extruder
#endif
};
// Where to park nozzle to wait for probe cooldown static int16_t *sensor_z_offsets[TSI_COUNT];
static constexpr xyz_pos_t park_point = PTC_PARK_POS; #if ENABLED(PTC_PROBE)
static int16_t z_offsets_probe[PTC_PROBE_COUNT]; // (µm)
// XY coordinates of nozzle for probing the bed #endif
static constexpr xy_pos_t measure_point = PTC_PROBE_POS; // Coordinates to probe #if ENABLED(PTC_BED)
//measure_point = { 12.0f, 7.3f }; // Coordinates for the MK52 magnetic heatbed static int16_t z_offsets_bed[PTC_BED_COUNT]; // (µm)
#endif
static constexpr celsius_t probe_calib_bed_temp = BED_MAX_TARGET, // Bed temperature while calibrating probe #if ENABLED(PTC_HOTEND)
bed_calib_probe_temp = BTC_PROBE_TEMP; // Probe temperature while calibrating bed static int16_t z_offsets_hotend[PTC_HOTEND_COUNT]; // (µm)
static int16_t *sensor_z_offsets[TSI_COUNT],
z_offsets_probe[cali_info_init[TSI_PROBE].measurements], // (µm)
z_offsets_bed[cali_info_init[TSI_BED].measurements]; // (µm)
#if ENABLED(USE_TEMP_EXT_COMPENSATION)
static int16_t z_offsets_ext[cali_info_init[TSI_EXT].measurements]; // (µm)
#endif #endif
static inline void reset_index() { calib_idx = 0; }; static inline void reset_index() { calib_idx = 0; };
static inline uint8_t get_index() { return calib_idx; } static inline uint8_t get_index() { return calib_idx; }
static void reset();
static void clear_offsets(const TempSensorID tsi); static void clear_offsets(const TempSensorID tsi);
static inline void clear_all_offsets() { static inline void clear_all_offsets() {
clear_offsets(TSI_BED); TERN_(PTC_PROBE, clear_offsets(TSI_PROBE));
clear_offsets(TSI_PROBE); TERN_(PTC_BED, clear_offsets(TSI_BED));
TERN_(USE_TEMP_EXT_COMPENSATION, clear_offsets(TSI_EXT)); TERN_(PTC_HOTEND, clear_offsets(TSI_EXT));
} }
static bool set_offset(const TempSensorID tsi, const uint8_t idx, const int16_t offset); static bool set_offset(const TempSensorID tsi, const uint8_t idx, const int16_t offset);
static void print_offsets(); static void print_offsets();
@ -156,4 +106,4 @@ class ProbeTempComp {
static bool linear_regression(const TempSensorID tsi, float &k, float &d); static bool linear_regression(const TempSensorID tsi, float &k, float &d);
}; };
extern ProbeTempComp temp_comp; extern ProbeTempComp ptc;

10
Marlin/src/gcode/bedlevel/abl/G29.cpp
View File

@ -36,7 +36,7 @@
#include "../../../module/probe.h" #include "../../../module/probe.h"
#include "../../queue.h" #include "../../queue.h"
#if ENABLED(PROBE_TEMP_COMPENSATION) #if HAS_PTC
#include "../../../feature/probe_temp_comp.h" #include "../../../feature/probe_temp_comp.h"
#include "../../../module/temperature.h" #include "../../../module/temperature.h"
#endif #endif
@ -645,11 +645,9 @@ G29_TYPE GcodeSuite::G29() {
break; // Breaks out of both loops break; // Breaks out of both loops
} }
#if ENABLED(PROBE_TEMP_COMPENSATION) TERN_(PTC_BED, ptc.compensate_measurement(TSI_BED, thermalManager.degBed(), abl.measured_z));
temp_comp.compensate_measurement(TSI_BED, thermalManager.degBed(), abl.measured_z); TERN_(PTC_PROBE, ptc.compensate_measurement(TSI_PROBE, thermalManager.degProbe(), abl.measured_z));
temp_comp.compensate_measurement(TSI_PROBE, thermalManager.degProbe(), abl.measured_z); TERN_(PTC_HOTEND, ptc.compensate_measurement(TSI_EXT, thermalManager.degHotend(0), abl.measured_z));
TERN_(USE_TEMP_EXT_COMPENSATION, temp_comp.compensate_measurement(TSI_EXT, thermalManager.degHotend(0), abl.measured_z));
#endif
#if ENABLED(AUTO_BED_LEVELING_LINEAR) #if ENABLED(AUTO_BED_LEVELING_LINEAR)

358
Marlin/src/gcode/calibrate/G76_M192_M871.cpp
View File

@ -1,358 +0,0 @@
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
/**
* G76_M871.cpp - Temperature calibration/compensation for z-probing
*/
#include "../../inc/MarlinConfig.h"
#if ENABLED(PROBE_TEMP_COMPENSATION)
#include "../gcode.h"
#include "../../module/motion.h"
#include "../../module/planner.h"
#include "../../module/probe.h"
#include "../../feature/bedlevel/bedlevel.h"
#include "../../module/temperature.h"
#include "../../module/probe.h"
#include "../../feature/probe_temp_comp.h"
#include "../../lcd/marlinui.h"
/**
* G76: calibrate probe and/or bed temperature offsets
* Notes:
* - When calibrating probe, bed temperature is held constant.
* Compensation values are deltas to first probe measurement at probe temp. = 30°C.
* - When calibrating bed, probe temperature is held constant.
* Compensation values are deltas to first probe measurement at bed temp. = 60°C.
* - The hotend will not be heated at any time.
* - On my Průša MK3S clone I put a piece of paper between the probe and the hotend
* so the hotend fan would not cool my probe constantly. Alternatively you could just
* make sure the fan is not running while running the calibration process.
*
* Probe calibration:
* - Moves probe to cooldown point.
* - Heats up bed to 100°C.
* - Moves probe to probing point (1mm above heatbed).
* - Waits until probe reaches target temperature (30°C).
* - Does a z-probing (=base value) and increases target temperature by 5°C.
* - Waits until probe reaches increased target temperature.
* - Does a z-probing (delta to base value will be a compensation value) and increases target temperature by 5°C.
* - Repeats last two steps until max. temperature reached or timeout (i.e. probe does not heat up any further).
* - Compensation values of higher temperatures will be extrapolated (using linear regression first).
* While this is not exact by any means it is still better than simply using the last compensation value.
*
* Bed calibration:
* - Moves probe to cooldown point.
* - Heats up bed to 60°C.
* - Moves probe to probing point (1mm above heatbed).
* - Waits until probe reaches target temperature (30°C).
* - Does a z-probing (=base value) and increases bed temperature by 5°C.
* - Moves probe to cooldown point.
* - Waits until probe is below 30°C and bed has reached target temperature.
* - Moves probe to probing point and waits until it reaches target temperature (30°C).
* - Does a z-probing (delta to base value will be a compensation value) and increases bed temperature by 5°C.
* - Repeats last four points until max. bed temperature reached (110°C) or timeout.
* - Compensation values of higher temperatures will be extrapolated (using linear regression first).
* While this is not exact by any means it is still better than simply using the last compensation value.
*
* G76 [B | P]
* - no flag - Both calibration procedures will be run.
* - `B` - Run bed temperature calibration.
* - `P` - Run probe temperature calibration.
*/
static void say_waiting_for() { SERIAL_ECHOPGM("Waiting for "); }
static void say_waiting_for_probe_heating() { say_waiting_for(); SERIAL_ECHOLNPGM("probe heating."); }
static void say_successfully_calibrated() { SERIAL_ECHOPGM("Successfully calibrated"); }
static void say_failed_to_calibrate() { SERIAL_ECHOPGM("!Failed to calibrate"); }
void GcodeSuite::G76() {
// Check if heated bed is available and z-homing is done with probe
#if TEMP_SENSOR_BED == 0 || !(HOMING_Z_WITH_PROBE)
return;
#endif
auto report_temps = [](millis_t &ntr, millis_t timeout=0) {
idle_no_sleep();
const millis_t ms = millis();
if (ELAPSED(ms, ntr)) {
ntr = ms + 1000;
thermalManager.print_heater_states(active_extruder);
}
return (timeout && ELAPSED(ms, timeout));
};
auto wait_for_temps = [&](const celsius_t tb, const celsius_t tp, millis_t &ntr, const millis_t timeout=0) {
say_waiting_for(); SERIAL_ECHOLNPGM("bed and probe temperature.");
while (thermalManager.wholeDegBed() != tb || thermalManager.wholeDegProbe() > tp)
if (report_temps(ntr, timeout)) return true;
return false;
};
auto g76_probe = [](const TempSensorID sid, celsius_t &targ, const xy_pos_t &nozpos) {
do_z_clearance(5.0); // Raise nozzle before probing
const float measured_z = probe.probe_at_point(nozpos, PROBE_PT_STOW, 0, false); // verbose=0, probe_relative=false
if (isnan(measured_z))
SERIAL_ECHOLNPGM("!Received NAN. Aborting.");
else {
SERIAL_ECHOLNPAIR_F("Measured: ", measured_z);
if (targ == cali_info_init[sid].start_temp)
temp_comp.prepare_new_calibration(measured_z);
else
temp_comp.push_back_new_measurement(sid, measured_z);
targ += cali_info_init[sid].temp_resolution;
}
return measured_z;
};
#if ENABLED(BLTOUCH)
// Make sure any BLTouch error condition is cleared
bltouch_command(BLTOUCH_RESET, BLTOUCH_RESET_DELAY);
set_bltouch_deployed(false);
#endif
bool do_bed_cal = parser.boolval('B'), do_probe_cal = parser.boolval('P');
if (!do_bed_cal && !do_probe_cal) do_bed_cal = do_probe_cal = true;
// Synchronize with planner
planner.synchronize();
const xyz_pos_t parkpos = temp_comp.park_point,
probe_pos_xyz = xyz_pos_t(temp_comp.measure_point) + xyz_pos_t({ 0.0f, 0.0f, PTC_PROBE_HEATING_OFFSET }),
noz_pos_xyz = probe_pos_xyz - probe.offset_xy; // Nozzle position based on probe position
if (do_bed_cal || do_probe_cal) {
// Ensure park position is reachable
bool reachable = position_is_reachable(parkpos) || WITHIN(parkpos.z, Z_MIN_POS - fslop, Z_MAX_POS + fslop);
if (!reachable)
SERIAL_ECHOLNPGM("!Park");
else {
// Ensure probe position is reachable
reachable = probe.can_reach(probe_pos_xyz);
if (!reachable) SERIAL_ECHOLNPGM("!Probe");
}
if (!reachable) {
SERIAL_ECHOLNPGM(" position unreachable - aborting.");
return;
}
process_subcommands_now(FPSTR(G28_STR));
}
remember_feedrate_scaling_off();
/******************************************
* Calibrate bed temperature offsets
******************************************/
// Report temperatures every second and handle heating timeouts
millis_t next_temp_report = millis() + 1000;
auto report_targets = [&](const celsius_t tb, const celsius_t tp) {
SERIAL_ECHOLNPGM("Target Bed:", tb, " Probe:", tp);
};
if (do_bed_cal) {
celsius_t target_bed = cali_info_init[TSI_BED].start_temp,
target_probe = temp_comp.bed_calib_probe_temp;
say_waiting_for(); SERIAL_ECHOLNPGM(" cooling.");
while (thermalManager.wholeDegBed() > target_bed || thermalManager.wholeDegProbe() > target_probe)
report_temps(next_temp_report);
// Disable leveling so it won't mess with us
TERN_(HAS_LEVELING, set_bed_leveling_enabled(false));
for (;;) {
thermalManager.setTargetBed(target_bed);
report_targets(target_bed, target_probe);
// Park nozzle
do_blocking_move_to(parkpos);
// Wait for heatbed to reach target temp and probe to cool below target temp
if (wait_for_temps(target_bed, target_probe, next_temp_report, millis() + MIN_TO_MS(15))) {
SERIAL_ECHOLNPGM("!Bed heating timeout.");
break;
}
// Move the nozzle to the probing point and wait for the probe to reach target temp
do_blocking_move_to(noz_pos_xyz);
say_waiting_for_probe_heating();
SERIAL_EOL();
while (thermalManager.wholeDegProbe() < target_probe)
report_temps(next_temp_report);
const float measured_z = g76_probe(TSI_BED, target_bed, noz_pos_xyz);
if (isnan(measured_z) || target_bed > (BED_MAX_TARGET)) break;
}
SERIAL_ECHOLNPGM("Retrieved measurements: ", temp_comp.get_index());
if (temp_comp.finish_calibration(TSI_BED)) {
say_successfully_calibrated();
SERIAL_ECHOLNPGM(" bed.");
}
else {
say_failed_to_calibrate();
SERIAL_ECHOLNPGM(" bed. Values reset.");
}
// Cleanup
thermalManager.setTargetBed(0);
TERN_(HAS_LEVELING, set_bed_leveling_enabled(true));
} // do_bed_cal
/********************************************
* Calibrate probe temperature offsets
********************************************/
if (do_probe_cal) {
// Park nozzle
do_blocking_move_to(parkpos);
// Initialize temperatures
const celsius_t target_bed = temp_comp.probe_calib_bed_temp;
thermalManager.setTargetBed(target_bed);
celsius_t target_probe = cali_info_init[TSI_PROBE].start_temp;
report_targets(target_bed, target_probe);
// Wait for heatbed to reach target temp and probe to cool below target temp
wait_for_temps(target_bed, target_probe, next_temp_report);
// Disable leveling so it won't mess with us
TERN_(HAS_LEVELING, set_bed_leveling_enabled(false));
bool timeout = false;
for (;;) {
// Move probe to probing point and wait for it to reach target temperature
do_blocking_move_to(noz_pos_xyz);
say_waiting_for_probe_heating();
SERIAL_ECHOLNPGM(" Bed:", target_bed, " Probe:", target_probe);
const millis_t probe_timeout_ms = millis() + SEC_TO_MS(900UL);
while (thermalManager.degProbe() < target_probe) {
if (report_temps(next_temp_report, probe_timeout_ms)) {
SERIAL_ECHOLNPGM("!Probe heating timed out.");
timeout = true;
break;
}
}
if (timeout) break;
const float measured_z = g76_probe(TSI_PROBE, target_probe, noz_pos_xyz);
if (isnan(measured_z) || target_probe > cali_info_init[TSI_PROBE].end_temp) break;
}
SERIAL_ECHOLNPGM("Retrieved measurements: ", temp_comp.get_index());
if (temp_comp.finish_calibration(TSI_PROBE))
say_successfully_calibrated();
else
say_failed_to_calibrate();
SERIAL_ECHOLNPGM(" probe.");
// Cleanup
thermalManager.setTargetBed(0);
TERN_(HAS_LEVELING, set_bed_leveling_enabled(true));
SERIAL_ECHOLNPGM("Final compensation values:");
temp_comp.print_offsets();
} // do_probe_cal
restore_feedrate_and_scaling();
}
/**
* M871: Report / reset temperature compensation offsets.
* Note: This does not affect values in EEPROM until M500.
*
* M871 [ R | B | P | E ]
*
* No Parameters - Print current offset values.
*
* Select only one of these flags:
* R - Reset all offsets to zero (i.e., disable compensation).
* B - Manually set offset for bed
* P - Manually set offset for probe
* E - Manually set offset for extruder
*
* With B, P, or E:
* I[index] - Index in the array
* V[value] - Adjustment in µm
*/
void GcodeSuite::M871() {
if (parser.seen('R')) {
// Reset z-probe offsets to factory defaults
temp_comp.clear_all_offsets();
SERIAL_ECHOLNPGM("Offsets reset to default.");
}
else if (parser.seen("BPE")) {
if (!parser.seenval('V')) return;
const int16_t offset_val = parser.value_int();
if (!parser.seenval('I')) return;
const int16_t idx = parser.value_int();
const TempSensorID mod = (parser.seen('B') ? TSI_BED :
#if ENABLED(USE_TEMP_EXT_COMPENSATION)
parser.seen('E') ? TSI_EXT :
#endif
TSI_PROBE
);
if (idx > 0 && temp_comp.set_offset(mod, idx - 1, offset_val))
SERIAL_ECHOLNPGM("Set value: ", offset_val);
else
SERIAL_ECHOLNPGM("!Invalid index. Failed to set value (note: value at index 0 is constant).");
}
else // Print current Z-probe adjustments. Note: Values in EEPROM might differ.
temp_comp.print_offsets();
}
/**
* M192: Wait for probe temperature sensor to reach a target
*
* Select only one of these flags:
* R - Wait for heating or cooling
* S - Wait only for heating
*/
void GcodeSuite::M192() {
if (DEBUGGING(DRYRUN)) return;
const bool no_wait_for_cooling = parser.seenval('S');
if (!no_wait_for_cooling && ! parser.seenval('R')) {
SERIAL_ERROR_MSG("No target temperature set.");
return;
}
const celsius_t target_temp = parser.value_celsius();
ui.set_status(thermalManager.isProbeBelowTemp(target_temp) ? GET_TEXT_F(MSG_PROBE_HEATING) : GET_TEXT_F(MSG_PROBE_COOLING));
thermalManager.wait_for_probe(target_temp, no_wait_for_cooling);
}
#endif // PROBE_TEMP_COMPENSATION

337
Marlin/src/gcode/calibrate/G76_M871.cpp Normal file
View File

@ -0,0 +1,337 @@
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
/**
* G76_M871.cpp - Temperature calibration/compensation for z-probing
*/
#include "../../inc/MarlinConfig.h"
#if HAS_PTC
#include "../gcode.h"
#include "../../module/motion.h"
#include "../../module/planner.h"
#include "../../module/probe.h"
#include "../../feature/bedlevel/bedlevel.h"
#include "../../module/temperature.h"
#include "../../module/probe.h"
#include "../../feature/probe_temp_comp.h"
#include "../../lcd/marlinui.h"
/**
* G76: calibrate probe and/or bed temperature offsets
* Notes:
* - When calibrating probe, bed temperature is held constant.
* Compensation values are deltas to first probe measurement at probe temp. = 30°C.
* - When calibrating bed, probe temperature is held constant.
* Compensation values are deltas to first probe measurement at bed temp. = 60°C.
* - The hotend will not be heated at any time.
* - On my Průša MK3S clone I put a piece of paper between the probe and the hotend
* so the hotend fan would not cool my probe constantly. Alternatively you could just
* make sure the fan is not running while running the calibration process.
*
* Probe calibration:
* - Moves probe to cooldown point.
* - Heats up bed to 100°C.
* - Moves probe to probing point (1mm above heatbed).
* - Waits until probe reaches target temperature (30°C).
* - Does a z-probing (=base value) and increases target temperature by 5°C.
* - Waits until probe reaches increased target temperature.
* - Does a z-probing (delta to base value will be a compensation value) and increases target temperature by 5°C.
* - Repeats last two steps until max. temperature reached or timeout (i.e. probe does not heat up any further).
* - Compensation values of higher temperatures will be extrapolated (using linear regression first).
* While this is not exact by any means it is still better than simply using the last compensation value.
*
* Bed calibration:
* - Moves probe to cooldown point.
* - Heats up bed to 60°C.
* - Moves probe to probing point (1mm above heatbed).
* - Waits until probe reaches target temperature (30°C).
* - Does a z-probing (=base value) and increases bed temperature by 5°C.
* - Moves probe to cooldown point.
* - Waits until probe is below 30°C and bed has reached target temperature.
* - Moves probe to probing point and waits until it reaches target temperature (30°C).
* - Does a z-probing (delta to base value will be a compensation value) and increases bed temperature by 5°C.
* - Repeats last four points until max. bed temperature reached (110°C) or timeout.
* - Compensation values of higher temperatures will be extrapolated (using linear regression first).
* While this is not exact by any means it is still better than simply using the last compensation value.
*
* G76 [B | P]
* - no flag - Both calibration procedures will be run.
* - `B` - Run bed temperature calibration.
* - `P` - Run probe temperature calibration.
*/
static void say_waiting_for() { SERIAL_ECHOPGM("Waiting for "); }
static void say_waiting_for_probe_heating() { say_waiting_for(); SERIAL_ECHOLNPGM("probe heating."); }
static void say_successfully_calibrated() { SERIAL_ECHOPGM("Successfully calibrated"); }
static void say_failed_to_calibrate() { SERIAL_ECHOPGM("!Failed to calibrate"); }
#if BOTH(PTC_PROBE, PTC_BED)
void GcodeSuite::G76() {
auto report_temps = [](millis_t &ntr, millis_t timeout=0) {
idle_no_sleep();
const millis_t ms = millis();
if (ELAPSED(ms, ntr)) {
ntr = ms + 1000;
thermalManager.print_heater_states(active_extruder);
}
return (timeout && ELAPSED(ms, timeout));
};
auto wait_for_temps = [&](const celsius_t tb, const celsius_t tp, millis_t &ntr, const millis_t timeout=0) {
say_waiting_for(); SERIAL_ECHOLNPGM("bed and probe temperature.");
while (thermalManager.wholeDegBed() != tb || thermalManager.wholeDegProbe() > tp)
if (report_temps(ntr, timeout)) return true;
return false;
};
auto g76_probe = [](const TempSensorID sid, celsius_t &targ, const xy_pos_t &nozpos) {
do_z_clearance(5.0); // Raise nozzle before probing
const float measured_z = probe.probe_at_point(nozpos, PROBE_PT_STOW, 0, false); // verbose=0, probe_relative=false
if (isnan(measured_z))
SERIAL_ECHOLNPGM("!Received NAN. Aborting.");
else {
SERIAL_ECHOLNPAIR_F("Measured: ", measured_z);
if (targ == ProbeTempComp::cali_info[sid].start_temp)
ptc.prepare_new_calibration(measured_z);
else
ptc.push_back_new_measurement(sid, measured_z);
targ += ProbeTempComp::cali_info[sid].temp_resolution;
}
return measured_z;
};
#if ENABLED(BLTOUCH)
// Make sure any BLTouch error condition is cleared
bltouch_command(BLTOUCH_RESET, BLTOUCH_RESET_DELAY);
set_bltouch_deployed(false);
#endif
bool do_bed_cal = parser.boolval('B'), do_probe_cal = parser.boolval('P');
if (!do_bed_cal && !do_probe_cal) do_bed_cal = do_probe_cal = true;
// Synchronize with planner
planner.synchronize();
#ifndef PTC_PROBE_HEATING_OFFSET
#define PTC_PROBE_HEATING_OFFSET 0
#endif
const xyz_pos_t parkpos = PTC_PARK_POS,
probe_pos_xyz = xyz_pos_t(PTC_PROBE_POS) + xyz_pos_t({ 0.0f, 0.0f, PTC_PROBE_HEATING_OFFSET }),
noz_pos_xyz = probe_pos_xyz - probe.offset_xy; // Nozzle position based on probe position
if (do_bed_cal || do_probe_cal) {
// Ensure park position is reachable
bool reachable = position_is_reachable(parkpos) || WITHIN(parkpos.z, Z_MIN_POS - fslop, Z_MAX_POS + fslop);
if (!reachable)
SERIAL_ECHOLNPGM("!Park");
else {
// Ensure probe position is reachable
reachable = probe.can_reach(probe_pos_xyz);
if (!reachable) SERIAL_ECHOLNPGM("!Probe");
}
if (!reachable) {
SERIAL_ECHOLNPGM(" position unreachable - aborting.");
return;
}
process_subcommands_now(FPSTR(G28_STR));
}
remember_feedrate_scaling_off();
/******************************************
* Calibrate bed temperature offsets
******************************************/
// Report temperatures every second and handle heating timeouts
millis_t next_temp_report = millis() + 1000;
auto report_targets = [&](const celsius_t tb, const celsius_t tp) {
SERIAL_ECHOLNPGM("Target Bed:", tb, " Probe:", tp);
};
if (do_bed_cal) {
celsius_t target_bed = PTC_BED_START,
target_probe = PTC_PROBE_TEMP;
say_waiting_for(); SERIAL_ECHOLNPGM(" cooling.");
while (thermalManager.wholeDegBed() > target_bed || thermalManager.wholeDegProbe() > target_probe)
report_temps(next_temp_report);
// Disable leveling so it won't mess with us
TERN_(HAS_LEVELING, set_bed_leveling_enabled(false));
for (uint8_t idx = 0; idx <= PTC_BED_COUNT; idx++) {
thermalManager.setTargetBed(target_bed);
report_targets(target_bed, target_probe);
// Park nozzle
do_blocking_move_to(parkpos);
// Wait for heatbed to reach target temp and probe to cool below target temp
if (wait_for_temps(target_bed, target_probe, next_temp_report, millis() + MIN_TO_MS(15))) {
SERIAL_ECHOLNPGM("!Bed heating timeout.");
break;
}
// Move the nozzle to the probing point and wait for the probe to reach target temp
do_blocking_move_to(noz_pos_xyz);
say_waiting_for_probe_heating();
SERIAL_EOL();
while (thermalManager.wholeDegProbe() < target_probe)
report_temps(next_temp_report);
const float measured_z = g76_probe(TSI_BED, target_bed, noz_pos_xyz);
if (isnan(measured_z) || target_bed > (BED_MAX_TARGET)) break;
}
SERIAL_ECHOLNPGM("Retrieved measurements: ", ptc.get_index());
if (ptc.finish_calibration(TSI_BED)) {
say_successfully_calibrated();
SERIAL_ECHOLNPGM(" bed.");
}
else {
say_failed_to_calibrate();
SERIAL_ECHOLNPGM(" bed. Values reset.");
}
// Cleanup
thermalManager.setTargetBed(0);
TERN_(HAS_LEVELING, set_bed_leveling_enabled(true));
} // do_bed_cal
/********************************************
* Calibrate probe temperature offsets
********************************************/
if (do_probe_cal) {
// Park nozzle
do_blocking_move_to(parkpos);
// Initialize temperatures
const celsius_t target_bed = BED_MAX_TARGET;
thermalManager.setTargetBed(target_bed);
celsius_t target_probe = PTC_PROBE_START;
report_targets(target_bed, target_probe);
// Wait for heatbed to reach target temp and probe to cool below target temp
wait_for_temps(target_bed, target_probe, next_temp_report);
// Disable leveling so it won't mess with us
TERN_(HAS_LEVELING, set_bed_leveling_enabled(false));
bool timeout = false;
for (uint8_t idx = 0; idx <= PTC_PROBE_COUNT; idx++) {
// Move probe to probing point and wait for it to reach target temperature
do_blocking_move_to(noz_pos_xyz);
say_waiting_for_probe_heating();
SERIAL_ECHOLNPGM(" Bed:", target_bed, " Probe:", target_probe);
const millis_t probe_timeout_ms = millis() + SEC_TO_MS(900UL);
while (thermalManager.degProbe() < target_probe) {
if (report_temps(next_temp_report, probe_timeout_ms)) {
SERIAL_ECHOLNPGM("!Probe heating timed out.");
timeout = true;
break;
}
}
if (timeout) break;
const float measured_z = g76_probe(TSI_PROBE, target_probe, noz_pos_xyz);
if (isnan(measured_z)) break;
}
SERIAL_ECHOLNPGM("Retrieved measurements: ", ptc.get_index());
if (ptc.finish_calibration(TSI_PROBE))
say_successfully_calibrated();
else
say_failed_to_calibrate();
SERIAL_ECHOLNPGM(" probe.");
// Cleanup
thermalManager.setTargetBed(0);
TERN_(HAS_LEVELING, set_bed_leveling_enabled(true));
SERIAL_ECHOLNPGM("Final compensation values:");
ptc.print_offsets();
} // do_probe_cal
restore_feedrate_and_scaling();
}
#endif // PTC_PROBE && PTC_BED
/**
* M871: Report / reset temperature compensation offsets.
* Note: This does not affect values in EEPROM until M500.
*
* M871 [ R | B | P | E ]
*
* No Parameters - Print current offset values.
*
* Select only one of these flags:
* R - Reset all offsets to zero (i.e., disable compensation).
* B - Manually set offset for bed
* P - Manually set offset for probe
* E - Manually set offset for extruder
*
* With B, P, or E:
* I[index] - Index in the array
* V[value] - Adjustment in µm
*/
void GcodeSuite::M871() {
if (parser.seen('R')) {
// Reset z-probe offsets to factory defaults
ptc.clear_all_offsets();
SERIAL_ECHOLNPGM("Offsets reset to default.");
}
else if (parser.seen("BPE")) {
if (!parser.seenval('V')) return;
const int16_t offset_val = parser.value_int();
if (!parser.seenval('I')) return;
const int16_t idx = parser.value_int();
const TempSensorID mod = TERN_(PTC_BED, parser.seen_test('B') ? TSI_BED :)
TERN_(PTC_HOTEND, parser.seen_test('E') ? TSI_EXT :)
TERN_(PTC_PROBE, parser.seen_test('P') ? TSI_PROBE :) TSI_COUNT;
if (mod == TSI_COUNT)
SERIAL_ECHOLNPGM("!Invalid sensor.");
else if (idx > 0 && ptc.set_offset(mod, idx - 1, offset_val))
SERIAL_ECHOLNPGM("Set value: ", offset_val);
else
SERIAL_ECHOLNPGM("!Invalid index. Failed to set value (note: value at index 0 is constant).");
}
else // Print current Z-probe adjustments. Note: Values in EEPROM might differ.
ptc.print_offsets();
}
#endif // HAS_PTC

9
Marlin/src/gcode/gcode.cpp
View File

@ -424,7 +424,7 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) {
case 61: G61(); break; // G61: Apply/restore saved coordinates. case 61: G61(); break; // G61: Apply/restore saved coordinates.
#endif #endif
#if ENABLED(PROBE_TEMP_COMPENSATION) #if BOTH(PTC_PROBE, PTC_BED)
case 76: G76(); break; // G76: Calibrate first layer compensation values case 76: G76(); break; // G76: Calibrate first layer compensation values
#endif #endif
@ -587,6 +587,10 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) {
case 191: M191(); break; // M191: Wait for chamber temperature to reach target case 191: M191(); break; // M191: Wait for chamber temperature to reach target
#endif #endif
#if HAS_TEMP_PROBE
case 192: M192(); break; // M192: Wait for probe temp
#endif
#if HAS_COOLER #if HAS_COOLER
case 143: M143(); break; // M143: Set cooler temperature case 143: M143(); break; // M143: Set cooler temperature
case 193: M193(); break; // M193: Wait for cooler temperature to reach target case 193: M193(); break; // M193: Wait for cooler temperature to reach target
@ -921,8 +925,7 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) {
case 852: M852(); break; // M852: Set Skew factors case 852: M852(); break; // M852: Set Skew factors
#endif #endif
#if ENABLED(PROBE_TEMP_COMPENSATION) #if HAS_PTC
case 192: M192(); break; // M192: Wait for probe temp
case 871: M871(); break; // M871: Print/reset/clear first layer temperature offset values case 871: M871(); break; // M871: Print/reset/clear first layer temperature offset values
#endif #endif

57
Marlin/src/gcode/gcode.h
View File

@ -66,7 +66,7 @@
* G42 - Coordinated move to a mesh point (Requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BLINEAR, or AUTO_BED_LEVELING_UBL) * G42 - Coordinated move to a mesh point (Requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BLINEAR, or AUTO_BED_LEVELING_UBL)
* G60 - Save current position. (Requires SAVED_POSITIONS) * G60 - Save current position. (Requires SAVED_POSITIONS)
* G61 - Apply/restore saved coordinates. (Requires SAVED_POSITIONS) * G61 - Apply/restore saved coordinates. (Requires SAVED_POSITIONS)
* G76 - Calibrate first layer temperature offsets. (Requires PROBE_TEMP_COMPENSATION) * G76 - Calibrate first layer temperature offsets. (Requires PTC_PROBE and PTC_BED)
* G80 - Cancel current motion mode (Requires GCODE_MOTION_MODES) * G80 - Cancel current motion mode (Requires GCODE_MOTION_MODES)
* G90 - Use Absolute Coordinates * G90 - Use Absolute Coordinates
* G91 - Use Relative Coordinates * G91 - Use Relative Coordinates
@ -88,6 +88,8 @@
* M16 - Expected printer check. (Requires EXPECTED_PRINTER_CHECK) * M16 - Expected printer check. (Requires EXPECTED_PRINTER_CHECK)
* M17 - Enable/Power all stepper motors * M17 - Enable/Power all stepper motors
* M18 - Disable all stepper motors; same as M84 * M18 - Disable all stepper motors; same as M84
*
*** Print from Media (SDSUPPORT) ***
* M20 - List SD card. (Requires SDSUPPORT) * M20 - List SD card. (Requires SDSUPPORT)
* M21 - Init SD card. (Requires SDSUPPORT) * M21 - Init SD card. (Requires SDSUPPORT)
* M22 - Release SD card. (Requires SDSUPPORT) * M22 - Release SD card. (Requires SDSUPPORT)
@ -100,30 +102,36 @@
* OR, with 'C' get the current filename. * OR, with 'C' get the current filename.
* M28 - Start SD write: "M28 /path/file.gco". (Requires SDSUPPORT) * M28 - Start SD write: "M28 /path/file.gco". (Requires SDSUPPORT)
* M29 - Stop SD write. (Requires SDSUPPORT) * M29 - Stop SD write. (Requires SDSUPPORT)
* M30 - Delete file from SD: "M30 /path/file.gco" * M30 - Delete file from SD: "M30 /path/file.gco" (Requires SDSUPPORT)
* M31 - Report time since last M109 or SD card start to serial. * M31 - Report time since last M109 or SD card start to serial.
* M32 - Select file and start SD print: "M32 [S<bytepos>] !/path/file.gco#". (Requires SDSUPPORT) * M32 - Select file and start SD print: "M32 [S<bytepos>] !/path/file.gco#". (Requires SDSUPPORT)
* Use P to run other files as sub-programs: "M32 P !filename#" * Use P to run other files as sub-programs: "M32 P !filename#"
* The '#' is necessary when calling from within sd files, as it stops buffer prereading * The '#' is necessary when calling from within sd files, as it stops buffer prereading
* M33 - Get the longname version of a path. (Requires LONG_FILENAME_HOST_SUPPORT) * M33 - Get the longname version of a path. (Requires LONG_FILENAME_HOST_SUPPORT)
* M34 - Set SD Card sorting options. (Requires SDCARD_SORT_ALPHA) * M34 - Set SD Card sorting options. (Requires SDCARD_SORT_ALPHA)
*
* M42 - Change pin status via gcode: M42 P<pin> S<value>. LED pin assumed if P is omitted. (Requires DIRECT_PIN_CONTROL) * M42 - Change pin status via gcode: M42 P<pin> S<value>. LED pin assumed if P is omitted. (Requires DIRECT_PIN_CONTROL)
* M43 - Display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins * M43 - Display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins (Requires PINS_DEBUGGING)
* M48 - Measure Z Probe repeatability: M48 P<points> X<pos> Y<pos> V<level> E<engage> L<legs> S<chizoid>. (Requires Z_MIN_PROBE_REPEATABILITY_TEST) * M48 - Measure Z Probe repeatability: M48 P<points> X<pos> Y<pos> V<level> E<engage> L<legs> S<chizoid>. (Requires Z_MIN_PROBE_REPEATABILITY_TEST)
*
* M73 - Set the progress percentage. (Requires LCD_SET_PROGRESS_MANUALLY) * M73 - Set the progress percentage. (Requires LCD_SET_PROGRESS_MANUALLY)
* M75 - Start the print job timer. * M75 - Start the print job timer.
* M76 - Pause the print job timer. * M76 - Pause the print job timer.
* M77 - Stop the print job timer. * M77 - Stop the print job timer.
* M78 - Show statistical information about the print jobs. (Requires PRINTCOUNTER) * M78 - Show statistical information about the print jobs. (Requires PRINTCOUNTER)
*
* M80 - Turn on Power Supply. (Requires PSU_CONTROL) * M80 - Turn on Power Supply. (Requires PSU_CONTROL)
* M81 - Turn off Power Supply. (Requires PSU_CONTROL) * M81 - Turn off Power Supply. (Requires PSU_CONTROL)
*
* M82 - Set E codes absolute (default). * M82 - Set E codes absolute (default).
* M83 - Set E codes relative while in Absolute (G90) mode. * M83 - Set E codes relative while in Absolute (G90) mode.
* M84 - Disable steppers until next move, or use S<seconds> to specify an idle * M84 - Disable steppers until next move, or use S<seconds> to specify an idle
* duration after which steppers should turn off. S0 disables the timeout. * duration after which steppers should turn off. S0 disables the timeout.
* M85 - Set inactivity shutdown timer with parameter S<seconds>. To disable set zero (default) * M85 - Set inactivity shutdown timer with parameter S<seconds>. To disable set zero (default)
* M92 - Set planner.settings.axis_steps_per_mm for one or more axes. * M92 - Set planner.settings.axis_steps_per_mm for one or more axes.
*
* M100 - Watch Free Memory (for debugging) (Requires M100_FREE_MEMORY_WATCHER) * M100 - Watch Free Memory (for debugging) (Requires M100_FREE_MEMORY_WATCHER)
*
* M104 - Set extruder target temp. * M104 - Set extruder target temp.
* M105 - Report current temperatures. * M105 - Report current temperatures.
* M106 - Set print fan speed. * M106 - Set print fan speed.
@ -132,23 +140,29 @@
* M109 - S<temp> Wait for extruder current temp to reach target temp. ** Wait only when heating! ** * M109 - S<temp> Wait for extruder current temp to reach target temp. ** Wait only when heating! **
* R<temp> Wait for extruder current temp to reach target temp. ** Wait for heating or cooling. ** * R<temp> Wait for extruder current temp to reach target temp. ** Wait for heating or cooling. **
* If AUTOTEMP is enabled, S<mintemp> B<maxtemp> F<factor>. Exit autotemp by any M109 without F * If AUTOTEMP is enabled, S<mintemp> B<maxtemp> F<factor>. Exit autotemp by any M109 without F
*
* M110 - Set the current line number. (Used by host printing) * M110 - Set the current line number. (Used by host printing)
* M111 - Set debug flags: "M111 S<flagbits>". See flag bits defined in enum.h. * M111 - Set debug flags: "M111 S<flagbits>". See flag bits defined in enum.h.
* M112 - Full Shutdown. * M112 - Full Shutdown.
*
* M113 - Get or set the timeout interval for Host Keepalive "busy" messages. (Requires HOST_KEEPALIVE_FEATURE) * M113 - Get or set the timeout interval for Host Keepalive "busy" messages. (Requires HOST_KEEPALIVE_FEATURE)
* M114 - Report current position. * M114 - Report current position.
* M115 - Report capabilities. (Extended capabilities requires EXTENDED_CAPABILITIES_REPORT) * M115 - Report capabilities. (Extended capabilities requires EXTENDED_CAPABILITIES_REPORT)
* M117 - Display a message on the controller screen. (Requires an LCD) * M117 - Display a message on the controller screen. (Requires an LCD)
* M118 - Display a message in the host console. * M118 - Display a message in the host console.
*
* M119 - Report endstops status. * M119 - Report endstops status.
* M120 - Enable endstops detection. * M120 - Enable endstops detection.
* M121 - Disable endstops detection. * M121 - Disable endstops detection.
*
* M122 - Debug stepper (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660 or L6470) * M122 - Debug stepper (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660 or L6470)
* M125 - Save current position and move to filament change position. (Requires PARK_HEAD_ON_PAUSE) * M125 - Save current position and move to filament change position. (Requires PARK_HEAD_ON_PAUSE)
*
* M126 - Solenoid Air Valve Open. (Requires BARICUDA) * M126 - Solenoid Air Valve Open. (Requires BARICUDA)
* M127 - Solenoid Air Valve Closed. (Requires BARICUDA) * M127 - Solenoid Air Valve Closed. (Requires BARICUDA)
* M128 - EtoP Open. (Requires BARICUDA) * M128 - EtoP Open. (Requires BARICUDA)
* M129 - EtoP Closed. (Requires BARICUDA) * M129 - EtoP Closed. (Requires BARICUDA)
*
* M140 - Set bed target temp. S<temp> * M140 - Set bed target temp. S<temp>
* M141 - Set heated chamber target temp. S<temp> (Requires a chamber heater) * M141 - Set heated chamber target temp. S<temp> (Requires a chamber heater)
* M143 - Set cooler target temp. S<temp> (Requires a laser cooling device) * M143 - Set cooler target temp. S<temp> (Requires a laser cooling device)
@ -161,9 +175,9 @@
* M164 - Commit the mix and save to a virtual tool (current, or as specified by 'S'). (Requires MIXING_EXTRUDER) * M164 - Commit the mix and save to a virtual tool (current, or as specified by 'S'). (Requires MIXING_EXTRUDER)
* M165 - Set the mix for the mixing extruder (and current virtual tool) with parameters ABCDHI. (Requires MIXING_EXTRUDER and DIRECT_MIXING_IN_G1) * M165 - Set the mix for the mixing extruder (and current virtual tool) with parameters ABCDHI. (Requires MIXING_EXTRUDER and DIRECT_MIXING_IN_G1)
* M166 - Set the Gradient Mix for the mixing extruder. (Requires GRADIENT_MIX) * M166 - Set the Gradient Mix for the mixing extruder. (Requires GRADIENT_MIX)
* M190 - S<temp> Wait for bed current temp to reach target temp. ** Wait only when heating! ** * M190 - Set bed target temperature and wait. R<temp> Set target temperature and wait. S<temp> Set, but only wait when heating. (Requires TEMP_SENSOR_BED)
* R<temp> Wait for bed current temp to reach target temp. ** Wait for heating or cooling. ** * M192 - Wait for probe to reach target temperature. (Requires TEMP_SENSOR_PROBE)
* M193 - R<temp> Wait for cooler temp to reach target temp. ** Wait for cooling. ** * M193 - R<temp> Wait for cooler to reach target temp. ** Wait for cooling. **
* M200 - Set filament diameter, D<diameter>, setting E axis units to cubic. (Use S0 to revert to linear units.) * M200 - Set filament diameter, D<diameter>, setting E axis units to cubic. (Use S0 to revert to linear units.)
* M201 - Set max acceleration in units/s^2 for print moves: "M201 X<accel> Y<accel> Z<accel> E<accel>" * M201 - Set max acceleration in units/s^2 for print moves: "M201 X<accel> Y<accel> Z<accel> E<accel>"
* M202 - Set max acceleration in units/s^2 for travel moves: "M202 X<accel> Y<accel> Z<accel> E<accel>" ** UNUSED IN MARLIN! ** * M202 - Set max acceleration in units/s^2 for travel moves: "M202 X<accel> Y<accel> Z<accel> E<accel>" ** UNUSED IN MARLIN! **
@ -183,7 +197,7 @@
* M218 - Set/get a tool offset: "M218 T<index> X<offset> Y<offset>". (Requires 2 or more extruders) * M218 - Set/get a tool offset: "M218 T<index> X<offset> Y<offset>". (Requires 2 or more extruders)
* M220 - Set Feedrate Percentage: "M220 S<percent>" (i.e., "FR" on the LCD) * M220 - Set Feedrate Percentage: "M220 S<percent>" (i.e., "FR" on the LCD)
* Use "M220 B" to back up the Feedrate Percentage and "M220 R" to restore it. (Requires an MMU_MODEL version 2 or 2S) * Use "M220 B" to back up the Feedrate Percentage and "M220 R" to restore it. (Requires an MMU_MODEL version 2 or 2S)
* M221 - Set Flow Percentage: "M221 S<percent>" * M221 - Set Flow Percentage: "M221 S<percent>" (Requires an extruder)
* M226 - Wait until a pin is in a given state: "M226 P<pin> S<state>" (Requires DIRECT_PIN_CONTROL) * M226 - Wait until a pin is in a given state: "M226 P<pin> S<state>" (Requires DIRECT_PIN_CONTROL)
* M240 - Trigger a camera to take a photograph. (Requires PHOTO_GCODE) * M240 - Trigger a camera to take a photograph. (Requires PHOTO_GCODE)
* M250 - Set LCD contrast: "M250 C<contrast>" (0-63). (Requires LCD support) * M250 - Set LCD contrast: "M250 C<contrast>" (0-63). (Requires LCD support)
@ -230,9 +244,9 @@
* M502 - Revert to the default "factory settings". ** Does not write them to EEPROM! ** * M502 - Revert to the default "factory settings". ** Does not write them to EEPROM! **
* M503 - Print the current settings (in memory): "M503 S<verbose>". S0 specifies compact output. * M503 - Print the current settings (in memory): "M503 S<verbose>". S0 specifies compact output.
* M504 - Validate EEPROM contents. (Requires EEPROM_SETTINGS) * M504 - Validate EEPROM contents. (Requires EEPROM_SETTINGS)
* M510 - Lock Printer * M510 - Lock Printer (Requires PASSWORD_FEATURE)
* M511 - Unlock Printer * M511 - Unlock Printer (Requires PASSWORD_UNLOCK_GCODE)
* M512 - Set/Change/Remove Password * M512 - Set/Change/Remove Password (Requires PASSWORD_CHANGE_GCODE)
* M524 - Abort the current SD print job started with M24. (Requires SDSUPPORT) * M524 - Abort the current SD print job started with M24. (Requires SDSUPPORT)
* M540 - Enable/disable SD card abort on endstop hit: "M540 S<state>". (Requires SD_ABORT_ON_ENDSTOP_HIT) * M540 - Enable/disable SD card abort on endstop hit: "M540 S<state>". (Requires SD_ABORT_ON_ENDSTOP_HIT)
* M552 - Get or set IP address. Enable/disable network interface. (Requires enabled Ethernet port) * M552 - Get or set IP address. Enable/disable network interface. (Requires enabled Ethernet port)
@ -252,7 +266,9 @@
* M808 - Set or Goto a Repeat Marker (Requires GCODE_REPEAT_MARKERS) * M808 - Set or Goto a Repeat Marker (Requires GCODE_REPEAT_MARKERS)
* M810-M819 - Define/execute a G-code macro (Requires GCODE_MACROS) * M810-M819 - Define/execute a G-code macro (Requires GCODE_MACROS)
* M851 - Set Z probe's XYZ offsets in current units. (Negative values: X=left, Y=front, Z=below) * M851 - Set Z probe's XYZ offsets in current units. (Negative values: X=left, Y=front, Z=below)
* M852 - Set skew factors: "M852 [I<xy>] [J<xz>] [K<yz>]". (Requires SKEW_CORRECTION_GCODE, and SKEW_CORRECTION_FOR_Z for IJ) * M852 - Set skew factors: "M852 [I<xy>] [J<xz>] [K<yz>]". (Requires SKEW_CORRECTION_GCODE, plus SKEW_CORRECTION_FOR_Z for IJ)
*
*** I2C_POSITION_ENCODERS ***
* M860 - Report the position of position encoder modules. * M860 - Report the position of position encoder modules.
* M861 - Report the status of position encoder modules. * M861 - Report the status of position encoder modules.
* M862 - Perform an axis continuity test for position encoder modules. * M862 - Perform an axis continuity test for position encoder modules.
@ -263,8 +279,8 @@
* M867 - Enable/disable or toggle error correction for position encoder modules. * M867 - Enable/disable or toggle error correction for position encoder modules.
* M868 - Report or set position encoder module error correction threshold. * M868 - Report or set position encoder module error correction threshold.
* M869 - Report position encoder module error. * M869 - Report position encoder module error.
* M871 - Print/reset/clear first layer temperature offset values. (Requires PROBE_TEMP_COMPENSATION) *
* M192 - Wait for probe temp (Requires PROBE_TEMP_COMPENSATION) * M871 - Print/reset/clear first layer temperature offset values. (Requires PTC_PROBE, PTC_BED, or PTC_HOTEND)
* M876 - Handle Prompt Response. (Requires HOST_PROMPT_SUPPORT and not EMERGENCY_PARSER) * M876 - Handle Prompt Response. (Requires HOST_PROMPT_SUPPORT and not EMERGENCY_PARSER)
* M900 - Get or Set Linear Advance K-factor. (Requires LIN_ADVANCE) * M900 - Get or Set Linear Advance K-factor. (Requires LIN_ADVANCE)
* M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660 or L6470) * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. (Requires at least one _DRIVER_TYPE defined as TMC2130/2160/5130/5160/2208/2209/2660 or L6470)
@ -282,13 +298,14 @@
* M951 - Set Magnetic Parking Extruder parameters. (Requires MAGNETIC_PARKING_EXTRUDER) * M951 - Set Magnetic Parking Extruder parameters. (Requires MAGNETIC_PARKING_EXTRUDER)
* M7219 - Control Max7219 Matrix LEDs. (Requires MAX7219_GCODE) * M7219 - Control Max7219 Matrix LEDs. (Requires MAX7219_GCODE)
* *
*** SCARA ***
* M360 - SCARA calibration: Move to cal-position ThetaA (0 deg calibration) * M360 - SCARA calibration: Move to cal-position ThetaA (0 deg calibration)
* M361 - SCARA calibration: Move to cal-position ThetaB (90 deg calibration - steps per degree) * M361 - SCARA calibration: Move to cal-position ThetaB (90 deg calibration - steps per degree)
* M362 - SCARA calibration: Move to cal-position PsiA (0 deg calibration) * M362 - SCARA calibration: Move to cal-position PsiA (0 deg calibration)
* M363 - SCARA calibration: Move to cal-position PsiB (90 deg calibration - steps per degree) * M363 - SCARA calibration: Move to cal-position PsiB (90 deg calibration - steps per degree)
* M364 - SCARA calibration: Move to cal-position PSIC (90 deg to Theta calibration position) * M364 - SCARA calibration: Move to cal-position PSIC (90 deg to Theta calibration position)
* *
* ************ Custom codes - This can change to suit future G-code regulations *** Custom codes (can be changed to suit future G-code standards) ***
* G425 - Calibrate using a conductive object. (Requires CALIBRATION_GCODE) * G425 - Calibrate using a conductive object. (Requires CALIBRATION_GCODE)
* M928 - Start SD logging: "M928 filename.gco". Stop with M29. (Requires SDSUPPORT) * M928 - Start SD logging: "M928 filename.gco". Stop with M29. (Requires SDSUPPORT)
* M993 - Backup SPI Flash to SD * M993 - Backup SPI Flash to SD
@ -296,10 +313,11 @@
* M995 - Touch screen calibration for TFT display * M995 - Touch screen calibration for TFT display
* M997 - Perform in-application firmware update * M997 - Perform in-application firmware update
* M999 - Restart after being stopped by error * M999 - Restart after being stopped by error
*
* D... - Custom Development G-code. Add hooks to 'gcode_D.cpp' for developers to test features. (Requires MARLIN_DEV_MODE) * D... - Custom Development G-code. Add hooks to 'gcode_D.cpp' for developers to test features. (Requires MARLIN_DEV_MODE)
* D576 - Set buffer monitoring options. (Requires BUFFER_MONITORING) * D576 - Set buffer monitoring options. (Requires BUFFER_MONITORING)
* *
* "T" Codes *** "T" Codes ***
* *
* T0-T3 - Select an extruder (tool) by index: "T<n> F<units/min>" * T0-T3 - Select an extruder (tool) by index: "T<n> F<units/min>"
*/ */
@ -551,7 +569,7 @@ private:
static void G59(); static void G59();
#endif #endif
#if ENABLED(PROBE_TEMP_COMPENSATION) #if BOTH(PTC_PROBE, PTC_BED)
static void G76(); static void G76();
#endif #endif
@ -744,6 +762,10 @@ private:
static void M191(); static void M191();
#endif #endif
#if HAS_TEMP_PROBE
static void M192();
#endif
#if HAS_COOLER #if HAS_COOLER
static void M143(); static void M143();
static void M193(); static void M193();
@ -1087,8 +1109,7 @@ private:
FORCE_INLINE static void M869() { I2CPEM.M869(); } FORCE_INLINE static void M869() { I2CPEM.M869(); }
#endif #endif
#if ENABLED(PROBE_TEMP_COMPENSATION) #if HAS_PTC
static void M192();
static void M871(); static void M871();
#endif #endif

56
Marlin/src/gcode/temp/M192.cpp Normal file
View File

@ -0,0 +1,56 @@
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <https://www.gnu.org/licenses/>.
*
*/
/**
* M192.cpp - Wait for probe to reach temperature
*/
#include "../../inc/MarlinConfig.h"
#if HAS_TEMP_PROBE
#include "../gcode.h"
#include "../../module/temperature.h"
#include "../../lcd/marlinui.h"
/**
* M192: Wait for probe temperature sensor to reach a target
*
* Select only one of these flags:
* R - Wait for heating or cooling
* S - Wait only for heating
*/
void GcodeSuite::M192() {
if (DEBUGGING(DRYRUN)) return;
const bool no_wait_for_cooling = parser.seenval('S');
if (!no_wait_for_cooling && !parser.seenval('R')) {
SERIAL_ERROR_MSG("No target temperature set.");
return;
}
const celsius_t target_temp = parser.value_celsius();
ui.set_status(thermalManager.isProbeBelowTemp(target_temp) ? GET_TEXT_F(MSG_PROBE_HEATING) : GET_TEXT_F(MSG_PROBE_COOLING));
thermalManager.wait_for_probe(target_temp, no_wait_for_cooling);
}
#endif // HAS_TEMP_PROBE

14
Marlin/src/inc/Conditionals_adv.h
View File

@ -550,6 +550,20 @@
#endif #endif
#endif #endif
// Probe Temperature Compensation
#if !TEMP_SENSOR_PROBE
#undef PTC_PROBE
#endif
#if !TEMP_SENSOR_BED
#undef PTC_BED
#endif
#if !HAS_EXTRUDERS
#undef PTC_HOTEND
#endif
#if ANY(PTC_PROBE, PTC_BED, PTC_HOTEND)
#define HAS_PTC 1
#endif
// Let SD_FINISHED_RELEASECOMMAND stand in for SD_FINISHED_STEPPERRELEASE // Let SD_FINISHED_RELEASECOMMAND stand in for SD_FINISHED_STEPPERRELEASE
#if ENABLED(SD_FINISHED_STEPPERRELEASE) #if ENABLED(SD_FINISHED_STEPPERRELEASE)
#ifndef SD_FINISHED_RELEASECOMMAND #ifndef SD_FINISHED_RELEASECOMMAND

66
Marlin/src/inc/SanityCheck.h
View File

@ -597,6 +597,10 @@
#error "SPINDLE_LASER_PWM (true) is now set with SPINDLE_LASER_USE_PWM (enabled)." #error "SPINDLE_LASER_PWM (true) is now set with SPINDLE_LASER_USE_PWM (enabled)."
#elif ANY(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) #elif ANY(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF)
#error "The IS_RAMPS_* conditionals (for heater/fan/bed pins) are now called FET_ORDER_*." #error "The IS_RAMPS_* conditionals (for heater/fan/bed pins) are now called FET_ORDER_*."
#elif defined(PROBE_TEMP_COMPENSATION)
#error "PROBE_TEMP_COMPENSATION is now set using the PTC_PROBE, PTC_BED, PTC_HOTEND options."
#elif defined(BTC_PROBE_TEMP)
#error "BTC_PROBE_TEMP is now PTC_PROBE_TEMP."
#endif #endif
#if MB(DUE3DOM_MINI) && PIN_EXISTS(TEMP_2) && DISABLED(TEMP_SENSOR_BOARD) #if MB(DUE3DOM_MINI) && PIN_EXISTS(TEMP_2) && DISABLED(TEMP_SENSOR_BOARD)
@ -611,60 +615,60 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
/** /**
* Probe temp compensation requirements * Probe temp compensation requirements
*/ */
#if HAS_PTC
#if ENABLED(PROBE_TEMP_COMPENSATION) #if TEMP_SENSOR_PROBE && TEMP_SENSOR_BED
#if defined(PTC_PARK_POS_X) || defined(PTC_PARK_POS_Y) || defined(PTC_PARK_POS_Z) #if defined(PTC_PARK_POS_X) || defined(PTC_PARK_POS_Y) || defined(PTC_PARK_POS_Z)
#error "PTC_PARK_POS_[XYZ] is now PTC_PARK_POS (array)." #error "PTC_PARK_POS_[XYZ] is now PTC_PARK_POS (array)."
#elif !defined(PTC_PARK_POS) #elif !defined(PTC_PARK_POS)
#error "PROBE_TEMP_COMPENSATION requires PTC_PARK_POS." #error "PTC_PARK_POS is required for Probe Temperature Compensation."
#elif defined(PTC_PROBE_POS_X) || defined(PTC_PROBE_POS_Y) #elif defined(PTC_PROBE_POS_X) || defined(PTC_PROBE_POS_Y)
#error "PTC_PROBE_POS_[XY] is now PTC_PROBE_POS (array)." #error "PTC_PROBE_POS_[XY] is now PTC_PROBE_POS (array)."
#elif !defined(PTC_PROBE_POS) #elif !defined(PTC_PROBE_POS)
#error "PROBE_TEMP_COMPENSATION requires PTC_PROBE_POS." #error "PTC_PROBE_POS is required for Probe Temperature Compensation."
#endif
#endif #endif
#ifdef PTC_SAMPLE_START #ifdef PTC_PROBE_START
constexpr auto _ptc_sample_start = PTC_SAMPLE_START; constexpr auto _ptc_sample_start = PTC_PROBE_START;
constexpr decltype(_ptc_sample_start) _test_ptc_sample_start = 12.3f; constexpr decltype(_ptc_sample_start) _test_ptc_sample_start = 12.3f;
static_assert(_test_ptc_sample_start != 12.3f, "PTC_SAMPLE_START must be a whole number."); static_assert(_test_ptc_sample_start != 12.3f, "PTC_PROBE_START must be a whole number.");
#endif #endif
#ifdef PTC_SAMPLE_RES #ifdef PTC_PROBE_RES
constexpr auto _ptc_sample_res = PTC_SAMPLE_RES; constexpr auto _ptc_sample_res = PTC_PROBE_RES;
constexpr decltype(_ptc_sample_res) _test_ptc_sample_res = 12.3f; constexpr decltype(_ptc_sample_res) _test_ptc_sample_res = 12.3f;
static_assert(_test_ptc_sample_res != 12.3f, "PTC_SAMPLE_RES must be a whole number."); static_assert(_test_ptc_sample_res != 12.3f, "PTC_PROBE_RES must be a whole number.");
#endif #endif
#ifdef BTC_SAMPLE_START #ifdef PTC_BED_START
constexpr auto _btc_sample_start = BTC_SAMPLE_START; constexpr auto _btc_sample_start = PTC_BED_START;
constexpr decltype(_btc_sample_start) _test_btc_sample_start = 12.3f; constexpr decltype(_btc_sample_start) _test_btc_sample_start = 12.3f;
static_assert(_test_btc_sample_start != 12.3f, "BTC_SAMPLE_START must be a whole number."); static_assert(_test_btc_sample_start != 12.3f, "PTC_BED_START must be a whole number.");
#endif #endif
#ifdef BTC_SAMPLE_RES #ifdef PTC_BED_RES
constexpr auto _btc_sample_res = BTC_SAMPLE_RES; constexpr auto _btc_sample_res = PTC_BED_RES;
constexpr decltype(_btc_sample_res) _test_btc_sample_res = 12.3f; constexpr decltype(_btc_sample_res) _test_btc_sample_res = 12.3f;
static_assert(_test_btc_sample_res != 12.3f, "BTC_SAMPLE_RES must be a whole number."); static_assert(_test_btc_sample_res != 12.3f, "PTC_BED_RES must be a whole number.");
#endif #endif
#ifdef BTC_PROBE_TEMP #ifdef PTC_PROBE_TEMP
constexpr auto _btc_probe_temp = BTC_PROBE_TEMP; constexpr auto _btc_probe_temp = PTC_PROBE_TEMP;
constexpr decltype(_btc_probe_temp) _test_btc_probe_temp = 12.3f; constexpr decltype(_btc_probe_temp) _test_btc_probe_temp = 12.3f;
static_assert(_test_btc_probe_temp != 12.3f, "BTC_PROBE_TEMP must be a whole number."); static_assert(_test_btc_probe_temp != 12.3f, "PTC_PROBE_TEMP must be a whole number.");
#endif #endif
#if ENABLED(USE_TEMP_EXT_COMPENSATION) #if ENABLED(PTC_HOTEND)
#ifdef ETC_SAMPLE_START #if EXTRUDERS != 1
constexpr auto _etc_sample_start = ETC_SAMPLE_START; #error "PTC_HOTEND only works with a single extruder."
#endif
#ifdef PTC_HOTEND_START
constexpr auto _etc_sample_start = PTC_HOTEND_START;
constexpr decltype(_etc_sample_start) _test_etc_sample_start = 12.3f; constexpr decltype(_etc_sample_start) _test_etc_sample_start = 12.3f;
static_assert(_test_etc_sample_start != 12.3f, "ETC_SAMPLE_START must be a whole number."); static_assert(_test_etc_sample_start != 12.3f, "PTC_HOTEND_START must be a whole number.");
#endif #endif
#ifdef ETC_SAMPLE_RES #ifdef PTC_HOTEND_RES
constexpr auto _etc_sample_res = ETC_SAMPLE_RES; constexpr auto _etc_sample_res = PTC_HOTEND_RES;
constexpr decltype(_etc_sample_res) _test_etc_sample_res = 12.3f; constexpr decltype(_etc_sample_res) _test_etc_sample_res = 12.3f;
static_assert(_test_etc_sample_res != 12.3f, "ETC_SAMPLE_RES must be a whole number."); static_assert(_test_etc_sample_res != 12.3f, "PTC_HOTEND_RES must be a whole number.");
#endif #endif
#endif #endif
#endif // HAS_PTC
#if ENABLED(USE_TEMP_EXT_COMPENSATION) && EXTRUDERS != 1
#error "USE_TEMP_EXT_COMPENSATION only works with a single extruder."
#endif
#endif
/** /**
* Marlin release, version and default string * Marlin release, version and default string

52
Marlin/src/module/settings.cpp
View File

@ -128,7 +128,7 @@
#include "../feature/tmc_util.h" #include "../feature/tmc_util.h"
#endif #endif
#if ENABLED(PROBE_TEMP_COMPENSATION) #if HAS_PTC
#include "../feature/probe_temp_comp.h" #include "../feature/probe_temp_comp.h"
#endif #endif
@ -264,13 +264,16 @@ typedef struct SettingsDataStruct {
// //
// Temperature first layer compensation values // Temperature first layer compensation values
// //
#if ENABLED(PROBE_TEMP_COMPENSATION) #if HAS_PTC
int16_t z_offsets_probe[COUNT(temp_comp.z_offsets_probe)], // M871 P I V #if ENABLED(PTC_PROBE)
z_offsets_bed[COUNT(temp_comp.z_offsets_bed)] // M871 B I V int16_t z_offsets_probe[COUNT(ptc.z_offsets_probe)]; // M871 P I V
#if ENABLED(USE_TEMP_EXT_COMPENSATION) #endif
, z_offsets_ext[COUNT(temp_comp.z_offsets_ext)] // M871 E I V #if ENABLED(PTC_BED)
int16_t z_offsets_bed[COUNT(ptc.z_offsets_bed)]; // M871 B I V
#endif
#if ENABLED(PTC_HOTEND)
int16_t z_offsets_hotend[COUNT(ptc.z_offsets_hotend)]; // M871 E I V
#endif #endif
;
#endif #endif
// //
@ -844,11 +847,15 @@ void MarlinSettings::postprocess() {
// //
// Thermal first layer compensation values // Thermal first layer compensation values
// //
#if ENABLED(PROBE_TEMP_COMPENSATION) #if HAS_PTC
EEPROM_WRITE(temp_comp.z_offsets_probe); #if ENABLED(PTC_PROBE)
EEPROM_WRITE(temp_comp.z_offsets_bed); EEPROM_WRITE(ptc.z_offsets_probe);
#if ENABLED(USE_TEMP_EXT_COMPENSATION) #endif
EEPROM_WRITE(temp_comp.z_offsets_ext); #if ENABLED(PTC_BED)
EEPROM_WRITE(ptc.z_offsets_bed);
#endif
#if ENABLED(PTC_HOTEND)
EEPROM_WRITE(ptc.z_offsets_hotend);
#endif #endif
#else #else
// No placeholder data for this feature // No placeholder data for this feature
@ -1710,13 +1717,17 @@ void MarlinSettings::postprocess() {
// //
// Thermal first layer compensation values // Thermal first layer compensation values
// //
#if ENABLED(PROBE_TEMP_COMPENSATION) #if HAS_PTC
EEPROM_READ(temp_comp.z_offsets_probe); #if ENABLED(PTC_PROBE)
EEPROM_READ(temp_comp.z_offsets_bed); EEPROM_READ(ptc.z_offsets_probe);
#if ENABLED(USE_TEMP_EXT_COMPENSATION)
EEPROM_READ(temp_comp.z_offsets_ext);
#endif #endif
temp_comp.reset_index(); # if ENABLED(PTC_BED)
EEPROM_READ(ptc.z_offsets_bed);
#endif
#if ENABLED(PTC_HOTEND)
EEPROM_READ(ptc.z_offsets_hotend);
#endif
ptc.reset_index();
#else #else
// No placeholder data for this feature // No placeholder data for this feature
#endif #endif
@ -2728,6 +2739,11 @@ void MarlinSettings::reset() {
// //
TERN_(EDITABLE_SERVO_ANGLES, COPY(servo_angles, base_servo_angles)); // When not editable only one copy of servo angles exists TERN_(EDITABLE_SERVO_ANGLES, COPY(servo_angles, base_servo_angles)); // When not editable only one copy of servo angles exists
//
// Probe Temperature Compensation
//
TERN_(HAS_PTC, ptc.reset());
// //
// BLTOUCH // BLTOUCH
// //

8
buildroot/tests/rambo
View File

@ -18,7 +18,7 @@ opt_set MOTHERBOARD BOARD_RAMBO \
FANMUX0_PIN 53 FANMUX0_PIN 53
opt_disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN USE_WATCHDOG opt_disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN USE_WATCHDOG
opt_enable USE_ZMAX_PLUG REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST \ opt_enable USE_ZMAX_PLUG REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_PROGRESS_BAR_TEST \
FIX_MOUNTED_PROBE CODEPENDENT_XY_HOMING PIDTEMPBED PROBE_TEMP_COMPENSATION \ FIX_MOUNTED_PROBE CODEPENDENT_XY_HOMING PIDTEMPBED PTC_PROBE PTC_BED \
PREHEAT_BEFORE_PROBING PROBING_HEATERS_OFF PROBING_FANS_OFF PROBING_STEPPERS_OFF WAIT_FOR_BED_HEATER \ PREHEAT_BEFORE_PROBING PROBING_HEATERS_OFF PROBING_FANS_OFF PROBING_STEPPERS_OFF WAIT_FOR_BED_HEATER \
EEPROM_SETTINGS SDSUPPORT SD_REPRINT_LAST_SELECTED_FILE BINARY_FILE_TRANSFER \ EEPROM_SETTINGS SDSUPPORT SD_REPRINT_LAST_SELECTED_FILE BINARY_FILE_TRANSFER \
BLINKM PCA9533 PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \ BLINKM PCA9533 PCA9632 RGB_LED RGB_LED_R_PIN RGB_LED_G_PIN RGB_LED_B_PIN LED_CONTROL_MENU \
@ -61,16 +61,16 @@ opt_disable MIN_SOFTWARE_ENDSTOP_Z MAX_SOFTWARE_ENDSTOPS
exec_test $1 $2 "Rambo CNC Configuration" "$3" exec_test $1 $2 "Rambo CNC Configuration" "$3"
# #
# Rambo heated bed only # Rambo heated bed and probe temp sensor
# #
restore_configs restore_configs
opt_set MOTHERBOARD BOARD_RAMBO EXTRUDERS 0 TEMP_SENSOR_BED 1 \ opt_set MOTHERBOARD BOARD_RAMBO EXTRUDERS 0 TEMP_SENSOR_BED 1 TEMP_SENSOR_PROBE 1 TEMP_PROBE_PIN 12 \
DEFAULT_AXIS_STEPS_PER_UNIT '{ 80, 80, 4000 }' \ DEFAULT_AXIS_STEPS_PER_UNIT '{ 80, 80, 4000 }' \
DEFAULT_MAX_FEEDRATE '{ 300, 300, 5 }' \ DEFAULT_MAX_FEEDRATE '{ 300, 300, 5 }' \
DEFAULT_MAX_ACCELERATION '{ 3000, 3000, 100 }' \ DEFAULT_MAX_ACCELERATION '{ 3000, 3000, 100 }' \
MANUAL_FEEDRATE '{ 50*60, 50*60, 4*60 }' \ MANUAL_FEEDRATE '{ 50*60, 50*60, 4*60 }' \
AXIS_RELATIVE_MODES '{ false, false, false }' AXIS_RELATIVE_MODES '{ false, false, false }'
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER FIX_MOUNTED_PROBE Z_SAFE_HOMING
exec_test $1 $2 "Rambo heated bed only" "$3" exec_test $1 $2 "Rambo heated bed only" "$3"
# #

9
ini/features.ini
View File

@ -136,20 +136,20 @@ ADVANCED_PAUSE_FEATURE = src_filter=+<src/feature/pause.cpp> +<s
PSU_CONTROL = src_filter=+<src/feature/power.cpp> PSU_CONTROL = src_filter=+<src/feature/power.cpp>
HAS_POWER_MONITOR = src_filter=+<src/feature/power_monitor.cpp> +<src/gcode/feature/power_monitor> HAS_POWER_MONITOR = src_filter=+<src/feature/power_monitor.cpp> +<src/gcode/feature/power_monitor>
POWER_LOSS_RECOVERY = src_filter=+<src/feature/powerloss.cpp> +<src/gcode/feature/powerloss> POWER_LOSS_RECOVERY = src_filter=+<src/feature/powerloss.cpp> +<src/gcode/feature/powerloss>
PROBE_TEMP_COMPENSATION = src_filter=+<src/feature/probe_temp_comp.cpp> +<src/gcode/calibrate/G76_M192_M871.cpp> HAS_PTC = src_filter=+<src/feature/probe_temp_comp.cpp> +<src/gcode/calibrate/G76_M871.cpp>
HAS_FILAMENT_SENSOR = src_filter=+<src/feature/runout.cpp> +<src/gcode/feature/runout> HAS_FILAMENT_SENSOR = src_filter=+<src/feature/runout.cpp> +<src/gcode/feature/runout>
(EXT|MANUAL)_SOLENOID.* = src_filter=+<src/feature/solenoid.cpp> +<src/gcode/control/M380_M381.cpp> (EXT|MANUAL)_SOLENOID.* = src_filter=+<src/feature/solenoid.cpp> +<src/gcode/control/M380_M381.cpp>
MK2_MULTIPLEXER = src_filter=+<src/feature/snmm.cpp> MK2_MULTIPLEXER = src_filter=+<src/feature/snmm.cpp>
HAS_CUTTER = src_filter=+<src/feature/spindle_laser.cpp> +<src/gcode/control/M3-M5.cpp> HAS_CUTTER = src_filter=+<src/feature/spindle_laser.cpp> +<src/gcode/control/M3-M5.cpp>
HAS_DRIVER_SAFE_POWER_PROTECT = src_filter=+<src/feature/stepper_driver_safety.cpp> HAS_DRIVER_SAFE_POWER_PROTECT = src_filter=+<src/feature/stepper_driver_safety.cpp>
EXPERIMENTAL_I2CBUS = src_filter=+<src/feature/twibus.cpp> +<src/gcode/feature/i2c> EXPERIMENTAL_I2CBUS = src_filter=+<src/feature/twibus.cpp> +<src/gcode/feature/i2c>
MECHANICAL_GANTRY_CAL.+ = src_filter=+<src/gcode/calibrate/G34.cpp>
Z_MULTI_ENDSTOPS = src_filter=+<src/gcode/calibrate/G34_M422.cpp>
Z_STEPPER_AUTO_ALIGN = src_filter=+<src/feature/z_stepper_align.cpp> +<src/gcode/calibrate/G34_M422.cpp>
G26_MESH_VALIDATION = src_filter=+<src/gcode/bedlevel/G26.cpp> G26_MESH_VALIDATION = src_filter=+<src/gcode/bedlevel/G26.cpp>
ASSISTED_TRAMMING = src_filter=+<src/feature/tramming.cpp> +<src/gcode/bedlevel/G35.cpp> ASSISTED_TRAMMING = src_filter=+<src/feature/tramming.cpp> +<src/gcode/bedlevel/G35.cpp>
HAS_MESH = src_filter=+<src/gcode/bedlevel/G42.cpp> HAS_MESH = src_filter=+<src/gcode/bedlevel/G42.cpp>
HAS_LEVELING = src_filter=+<src/gcode/bedlevel/M420.cpp> +<src/feature/bedlevel/bedlevel.cpp> HAS_LEVELING = src_filter=+<src/gcode/bedlevel/M420.cpp> +<src/feature/bedlevel/bedlevel.cpp>
MECHANICAL_GANTRY_CAL.+ = src_filter=+<src/gcode/calibrate/G34.cpp>
Z_MULTI_ENDSTOPS|Z_STEPPER_AUTO_ALIGN = src_filter=+<src/gcode/calibrate/G34_M422.cpp>
Z_STEPPER_AUTO_ALIGN = src_filter=+<src/feature/z_stepper_align.cpp>
DELTA_AUTO_CALIBRATION = src_filter=+<src/gcode/calibrate/G33.cpp> DELTA_AUTO_CALIBRATION = src_filter=+<src/gcode/calibrate/G33.cpp>
CALIBRATION_GCODE = src_filter=+<src/gcode/calibrate/G425.cpp> CALIBRATION_GCODE = src_filter=+<src/gcode/calibrate/G425.cpp>
Z_MIN_PROBE_REPEATABILITY_TEST = src_filter=+<src/gcode/calibrate/M48.cpp> Z_MIN_PROBE_REPEATABILITY_TEST = src_filter=+<src/gcode/calibrate/M48.cpp>
@ -209,6 +209,7 @@ SDSUPPORT = src_filter=+<src/sd/cardreader.cpp> +<s
HAS_MEDIA_SUBCALLS = src_filter=+<src/gcode/sd/M32.cpp> HAS_MEDIA_SUBCALLS = src_filter=+<src/gcode/sd/M32.cpp>
GCODE_REPEAT_MARKERS = src_filter=+<src/feature/repeat.cpp> +<src/gcode/sd/M808.cpp> GCODE_REPEAT_MARKERS = src_filter=+<src/feature/repeat.cpp> +<src/gcode/sd/M808.cpp>
HAS_EXTRUDERS = src_filter=+<src/gcode/units/M82_M83.cpp> +<src/gcode/temp/M104_M109.cpp> +<src/gcode/config/M221.cpp> HAS_EXTRUDERS = src_filter=+<src/gcode/units/M82_M83.cpp> +<src/gcode/temp/M104_M109.cpp> +<src/gcode/config/M221.cpp>
HAS_TEMP_PROBE = src_filter=+<src/gcode/temp/M192.cpp>
HAS_COOLER = src_filter=+<src/gcode/temp/M143_M193.cpp> HAS_COOLER = src_filter=+<src/gcode/temp/M143_M193.cpp>
HAS_COOLER|LASER_COOLANT_FLOW_METER = src_filter=+<src/feature/cooler.cpp> HAS_COOLER|LASER_COOLANT_FLOW_METER = src_filter=+<src/feature/cooler.cpp>
AUTO_REPORT_TEMPERATURES = src_filter=+<src/gcode/temp/M155.cpp> AUTO_REPORT_TEMPERATURES = src_filter=+<src/gcode/temp/M155.cpp>

3
platformio.ini
View File

@ -152,7 +152,7 @@ default_src_filter = +<src/*> -<src/config> -<src/HAL> +<src/HAL/shared>
-<src/gcode/calibrate/G33.cpp> -<src/gcode/calibrate/G33.cpp>
-<src/gcode/calibrate/G34.cpp> -<src/gcode/calibrate/G34.cpp>
-<src/gcode/calibrate/G34_M422.cpp> -<src/gcode/calibrate/G34_M422.cpp>
-<src/gcode/calibrate/G76_M192_M871.cpp> -<src/gcode/calibrate/G76_M871.cpp>
-<src/gcode/calibrate/G425.cpp> -<src/gcode/calibrate/G425.cpp>
-<src/gcode/calibrate/M12.cpp> -<src/gcode/calibrate/M12.cpp>
-<src/gcode/calibrate/M48.cpp> -<src/gcode/calibrate/M48.cpp>
@ -229,6 +229,7 @@ default_src_filter = +<src/*> -<src/config> -<src/HAL> +<src/HAL/shared>
-<src/gcode/sd/M808.cpp> -<src/gcode/sd/M808.cpp>
-<src/gcode/temp/M104_M109.cpp> -<src/gcode/temp/M104_M109.cpp>
-<src/gcode/temp/M155.cpp> -<src/gcode/temp/M155.cpp>
-<src/gcode/temp/M192.cpp>
-<src/gcode/units/G20_G21.cpp> -<src/gcode/units/G20_G21.cpp>
-<src/gcode/units/M82_M83.cpp> -<src/gcode/units/M82_M83.cpp>
-<src/gcode/units/M149.cpp> -<src/gcode/units/M149.cpp>