bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

Clean up excess whitespace, comment formatting

Browse Source
This commit is contained in:
Scott Lahteine
2017-04-28 17:36:31 -05:00
parent a35c681453
commit 0a8e09c723
8 changed files with 78 additions and 80 deletions
Download Patch File Download Diff File Expand all files Collapse all files

5
Marlin/example_configurations/FolgerTech-i3-2020/Configuration.h
View File

@ -316,8 +316,7 @@
#define K1 0.95 //smoothing factor within the PID
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
// FolgerTech i3-2020
#define DEFAULT_Kp 11.50
#define DEFAULT_Ki 0.50
@ -921,7 +920,7 @@
#define UBL_MESH_INSET 1 // Mesh inset margin on print area
#define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
#define GRID_MAX_POINTS_Y 10
#define UBL_PROBE_PT_1_X 45 // These set the probe locations for when UBL does a 3-Point leveling
#define UBL_PROBE_PT_1_X 45 // These set the probe locations for when UBL does a 3-Point leveling
#define UBL_PROBE_PT_1_Y 170 // of the mesh.
#define UBL_PROBE_PT_2_X 45
#define UBL_PROBE_PT_2_Y 25

14
Marlin/example_configurations/gCreate_gMax1.5+/Configuration.h
View File

@ -133,8 +133,8 @@
//#define MOTHERBOARD BOARD_RAMPS_14_EEF
#define MOTHERBOARD BOARD_RAMPS_14_EFB // gMax users please note: This is a Roxy modification. I print on glass and
// I use Marlin to control the bed's temperature. So, if you have a single nozzle
// machine, this will work fine for you. You just set the
// #define TEMP_SENSOR_BED 75 to 0 down below so Marlin doesn't mess with the bed
// machine, this will work fine for you. You just set the
// #define TEMP_SENSOR_BED 75 to 0 down below so Marlin doesn't mess with the bed
// temp.
#endif
@ -261,8 +261,8 @@
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_BED 75 // gMax-1.5+ users please note: This is a Roxy modification to the printer. I want
// to print on glass. And I'm using a 400mm x 400mm silicon heat pad powered through
// a Fortek SSR to do it. If you are using an unaltered gCreate machine, this needs
// to print on glass. And I'm using a 400mm x 400mm silicon heat pad powered through
// a Fortek SSR to do it. If you are using an unaltered gCreate machine, this needs
// to be set to 0
// Dummy thermistor constant temperature readings, for use with 998 and 999
@ -325,12 +325,12 @@
#define K1 0.95 //smoothing factor within the PID
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
// gMax J-Head
#define DEFAULT_Kp 15.35
#define DEFAULT_Ki 0.85
#define DEFAULT_Kd 69.45
// Ultimaker
// #define DEFAULT_Kp 22.2
// #define DEFAULT_Ki 1.08
@ -793,7 +793,7 @@
#define Y_MIN_POS 0
#define Z_MIN_POS 0
#define X_MAX_POS 420 // These numbers are not accurate for an unaltered gMax 1.5+ printer. My print bed
#define Y_MAX_POS 420 // is inset a noticable amount from the edge of the bed. Combined with the inset,
#define Y_MAX_POS 420 // is inset a noticable amount from the edge of the bed. Combined with the inset,
// the nozzle can reach all cordinates of the mesh.
#define Z_MAX_POS 500