bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity

✨ WYH L12864 LCD (Alfawise Ex8) (#22863)

Browse Source
This commit is contained in:
VragVideo 2021-10-03 06:12:51 +03:00 committed by Scott Lahteine
parent 58a26fcaac
commit 0273a68587
56 changed files with 181 additions and 101 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

5
Marlin/Configuration.h
View File

@ -2375,6 +2375,11 @@
//#define VIKI2 //#define VIKI2
//#define miniVIKI //#define miniVIKI
//
// Alfawise Ex8 printer LCD marked as WYH L12864 COG
//
//#define WYH_L12864
// //
// MakerLab Mini Panel with graphic // MakerLab Mini Panel with graphic
// controller and SD support - https://reprap.org/wiki/Mini_panel // controller and SD support - https://reprap.org/wiki/Mini_panel

2
Marlin/Configuration_adv.h
View File

@ -1603,7 +1603,7 @@
* Set STATUS_EXPIRE_SECONDS to zero to never clear the status. * Set STATUS_EXPIRE_SECONDS to zero to never clear the status.
* This will prevent position updates from being displayed. * This will prevent position updates from being displayed.
*/ */
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
// Enable this option and reduce the value to optimize screen updates. // Enable this option and reduce the value to optimize screen updates.
// The normal delay is 10µs. Use the lowest value that still gives a reliable display. // The normal delay is 10µs. Use the lowest value that still gives a reliable display.
//#define DOGM_SPI_DELAY_US 5 //#define DOGM_SPI_DELAY_US 5

4
Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_st7920_sw_spi.cpp
View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfigPre.h" #include "../../../inc/MarlinConfigPre.h"
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#include "../../../inc/MarlinConfig.h" #include "../../../inc/MarlinConfig.h"
#include "../../shared/Delay.h" #include "../../shared/Delay.h"
@ -182,5 +182,5 @@ uint8_t u8g_com_HAL_DUE_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_va
} }
#endif // LIGHTWEIGHT_UI #endif // LIGHTWEIGHT_UI
#endif // U8GLIB_ST7920 #endif // IS_U8GLIB_ST7920
#endif // ARDUINO_ARCH_SAM #endif // ARDUINO_ARCH_SAM

4
Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_sw_spi.cpp
View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfigPre.h" #include "../../../inc/MarlinConfigPre.h"
#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920) #if HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#include "u8g_com_HAL_DUE_sw_spi_shared.h" #include "u8g_com_HAL_DUE_sw_spi_shared.h"
@ -141,5 +141,5 @@ uint8_t u8g_com_HAL_DUE_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void
return 1; return 1;
} }
#endif // HAS_MARLINUI_U8GLIB && !U8GLIB_ST7920 #endif // HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#endif // ARDUINO_ARCH_SAM #endif // ARDUINO_ARCH_SAM

4
Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_st7920_sw_spi.cpp
View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfigPre.h" #include "../../../inc/MarlinConfigPre.h"
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#include <U8glib-HAL.h> #include <U8glib-HAL.h>
#include <SoftwareSPI.h> #include <SoftwareSPI.h>
@ -143,5 +143,5 @@ uint8_t u8g_com_HAL_LPC1768_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t ar
return 1; return 1;
} }
#endif // U8GLIB_ST7920 #endif // IS_U8GLIB_ST7920
#endif // TARGET_LPC1768 #endif // TARGET_LPC1768

4
Marlin/src/HAL/LPC1768/u8g/u8g_com_HAL_LPC1768_sw_spi.cpp
View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfigPre.h" #include "../../../inc/MarlinConfigPre.h"
#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920) #if HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#include <SoftwareSPI.h> #include <SoftwareSPI.h>
#include "../../shared/HAL_SPI.h" #include "../../shared/HAL_SPI.h"
@ -205,5 +205,5 @@ uint8_t u8g_com_HAL_LPC1768_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val,
return 1; return 1;
} }
#endif // HAS_MARLINUI_U8GLIB && !U8GLIB_ST7920 #endif // HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#endif // TARGET_LPC1768 #endif // TARGET_LPC1768

4
Marlin/src/HAL/NATIVE_SIM/u8g/u8g_com_st7920_sw_spi.cpp
View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfig.h" #include "../../../inc/MarlinConfig.h"
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#include <U8glib-HAL.h> #include <U8glib-HAL.h>
#include "../../shared/Delay.h" #include "../../shared/Delay.h"
@ -167,5 +167,5 @@ uint8_t u8g_com_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void
} }
#endif #endif
#endif // U8GLIB_ST7920 #endif // IS_U8GLIB_ST7920
#endif // TARGET_LPC1768 #endif // TARGET_LPC1768

4
Marlin/src/HAL/NATIVE_SIM/u8g/u8g_com_sw_spi.cpp
View File

@ -57,7 +57,7 @@
#include "../../../inc/MarlinConfig.h" #include "../../../inc/MarlinConfig.h"
#if HAS_MARLINUI_U8GLIB && DISABLED(U8GLIB_ST7920) #if HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#undef SPI_SPEED #undef SPI_SPEED
#define SPI_SPEED 2 // About 2 MHz #define SPI_SPEED 2 // About 2 MHz
@ -211,5 +211,5 @@ uint8_t u8g_com_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_pt
#elif !ANY(TFT_COLOR_UI, TFT_CLASSIC_UI, TFT_LVGL_UI, HAS_MARLINUI_HD44780) && HAS_MARLINUI_U8GLIB #elif !ANY(TFT_COLOR_UI, TFT_CLASSIC_UI, TFT_LVGL_UI, HAS_MARLINUI_HD44780) && HAS_MARLINUI_U8GLIB
#include <U8glib-HAL.h> #include <U8glib-HAL.h>
uint8_t u8g_com_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {return 0;} uint8_t u8g_com_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr) {return 0;}
#endif // HAS_MARLINUI_U8GLIB && !U8GLIB_ST7920 #endif // HAS_MARLINUI_U8GLIB && !IS_U8GLIB_ST7920
#endif // __PLAT_NATIVE_SIM__ #endif // __PLAT_NATIVE_SIM__

79
Marlin/src/inc/Conditionals_LCD.h
View File

@ -39,17 +39,17 @@
/** /**
* General Flags that may be set below by specific LCDs * General Flags that may be set below by specific LCDs
* *
* DOGLCD : Run a Graphical LCD through U8GLib (with MarlinUI) * DOGLCD : Run a Graphical LCD through U8GLib (with MarlinUI)
* IS_ULTIPANEL : Define LCD_PINS_D5/6/7 for direct-connected "Ultipanel" LCDs * IS_ULTIPANEL : Define LCD_PINS_D5/6/7 for direct-connected "Ultipanel" LCDs
* IS_ULTRA_LCD : Ultra LCD, not necessarily Ultipanel. * IS_ULTRA_LCD : Ultra LCD, not necessarily Ultipanel.
* IS_RRD_SC : Common RRD Smart Controller digital interface pins * IS_RRD_SC : Common RRD Smart Controller digital interface pins
* IS_RRD_FG_SC : Common RRD Full Graphical Smart Controller digital interface pins * IS_RRD_FG_SC : Common RRD Full Graphical Smart Controller digital interface pins
* U8GLIB_ST7920 : Most common DOGM display SPI interface, supporting a "lightweight" display mode. * IS_U8GLIB_ST7920 : Most common DOGM display SPI interface, supporting a "lightweight" display mode.
* U8GLIB_SH1106 : SH1106 OLED with I2C interface via U8GLib * U8GLIB_SH1106 : SH1106 OLED with I2C interface via U8GLib
* IS_U8GLIB_SSD1306 : SSD1306 OLED with I2C interface via U8GLib * IS_U8GLIB_SSD1306 : SSD1306 OLED with I2C interface via U8GLib (U8GLIB_SSD1306)
* U8GLIB_SSD1309 : SSD1309 OLED with I2C interface via U8GLib * U8GLIB_SSD1309 : SSD1309 OLED with I2C interface via U8GLib (HAS_U8GLIB_I2C_OLED, IS_ULTRA_LCD, DOGLCD)
* U8GLIB_ST7565_64128N : ST7565 128x64 LCD with SPI interface via U8GLib * IS_U8GLIB_ST7565_64128N : ST7565 128x64 LCD with SPI interface via U8GLib
* U8GLIB_LM6059_AF : LM6059 with Hardware SPI via U8GLib * IS_U8GLIB_LM6059_AF : LM6059 with Hardware SPI via U8GLib
*/ */
#if EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY) #if EITHER(MKS_MINI_12864, ENDER2_STOCKDISPLAY)
@ -85,7 +85,7 @@
#elif ENABLED(ZONESTAR_12864LCD) #elif ENABLED(ZONESTAR_12864LCD)
#define DOGLCD #define DOGLCD
#define IS_RRD_SC 1 #define IS_RRD_SC 1
#define U8GLIB_ST7920 #define IS_U8GLIB_ST7920 1
#elif ENABLED(ZONESTAR_12864OLED) #elif ENABLED(ZONESTAR_12864OLED)
#define IS_RRD_SC 1 #define IS_RRD_SC 1
@ -99,19 +99,24 @@
#define IS_ULTIPANEL 1 #define IS_ULTIPANEL 1
#define ENCODER_PULSES_PER_STEP 2 #define ENCODER_PULSES_PER_STEP 2
#elif ANY(miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864) #elif ANY(miniVIKI, VIKI2, WYH_L12864, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864)
#define IS_DOGM_12864 1
#define DOGLCD #define DOGLCD
#define IS_ULTIPANEL 1 #define IS_ULTIPANEL 1
#if ENABLED(miniVIKI) #if ENABLED(miniVIKI)
#define U8GLIB_ST7565_64128N #define IS_U8GLIB_ST7565_64128N 1
#elif ENABLED(VIKI2) #elif ENABLED(VIKI2)
#define U8GLIB_ST7565_64128N #define IS_U8GLIB_ST7565_64128N 1
#elif ENABLED(WYH_L12864)
#define IS_U8GLIB_ST7565_64128N 1
#define ST7565_XOFFSET 0x04
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define U8GLIB_LM6059_AF #define IS_U8GLIB_LM6059_AF 1
#elif ENABLED(AZSMZ_12864) #elif ENABLED(AZSMZ_12864)
#define U8GLIB_ST7565_64128N #define IS_U8GLIB_ST7565_64128N 1
#endif #endif
#elif ENABLED(OLED_PANEL_TINYBOY2) #elif ENABLED(OLED_PANEL_TINYBOY2)
@ -128,7 +133,7 @@
#elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD)
#define DOGLCD #define DOGLCD
#define U8GLIB_ST7920 #define IS_U8GLIB_ST7920 1
#define IS_ULTIPANEL 1 #define IS_ULTIPANEL 1
#elif ENABLED(MKS_12864OLED) #elif ENABLED(MKS_12864OLED)
@ -144,7 +149,7 @@
#elif ENABLED(SAV_3DGLCD) #elif ENABLED(SAV_3DGLCD)
#ifdef U8GLIB_SSD1306 #ifdef U8GLIB_SSD1306
#define IS_U8GLIB_SSD1306 #define IS_U8GLIB_SSD1306 // Allow for U8GLIB_SSD1306 + SAV_3DGLCD
#endif #endif
#define IS_NEWPANEL 1 #define IS_NEWPANEL 1
@ -266,7 +271,7 @@
// ST7920-based graphical displays // ST7920-based graphical displays
#if ANY(IS_RRD_FG_SC, LCD_FOR_MELZI, SILVER_GATE_GLCD_CONTROLLER) #if ANY(IS_RRD_FG_SC, LCD_FOR_MELZI, SILVER_GATE_GLCD_CONTROLLER)
#define DOGLCD #define DOGLCD
#define U8GLIB_ST7920 #define IS_U8GLIB_ST7920 1
#define IS_RRD_SC 1 #define IS_RRD_SC 1
#endif #endif
@ -275,7 +280,7 @@
#define IS_ULTIPANEL 1 #define IS_ULTIPANEL 1
#define DOGLCD #define DOGLCD
#if ENABLED(MAKRPANEL) #if ENABLED(MAKRPANEL)
#define U8GLIB_ST7565_64128N #define IS_U8GLIB_ST7565_64128N 1
#endif #endif
#endif #endif
@ -372,25 +377,28 @@
* I2C Panels * I2C Panels
*/ */
#if EITHER(LCD_SAINSMART_I2C_1602, LCD_SAINSMART_I2C_2004) #if ANY(IS_RRD_SC, IS_DOGM_12864, OLED_PANEL_TINYBOY2, LCD_I2C_PANELOLU2)
#define LCD_I2C_TYPE_PCF8575 #define STD_ENCODER_PULSES_PER_STEP 4
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander #define STD_ENCODER_STEPS_PER_MENU_ITEM 1
#if ENABLED(LCD_I2C_PANELOLU2) // PANELOLU2 LCD with status LEDs, separate encoder and click inputs
#define LCD_I2C_TYPE_MCP23017 // I2C Character-based 12864 display
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
#define LCD_USE_I2C_BUZZER // Enable buzzer on LCD (optional)
#define IS_ULTIPANEL 1
#endif
#elif EITHER(LCD_SAINSMART_I2C_1602, LCD_SAINSMART_I2C_2004)
#define LCD_I2C_TYPE_PCF8575 // I2C Character-based 12864 display
#define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander
#if ENABLED(LCD_SAINSMART_I2C_2004) #if ENABLED(LCD_SAINSMART_I2C_2004)
#define LCD_WIDTH 20 #define LCD_WIDTH 20
#define LCD_HEIGHT 4 #define LCD_HEIGHT 4
#endif #endif
#elif ENABLED(LCD_I2C_PANELOLU2)
// PANELOLU2 LCD with status LEDs, separate encoder and click inputs
#define LCD_I2C_TYPE_MCP23017
#define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander
#define LCD_USE_I2C_BUZZER // Enable buzzer on LCD (optional)
#define IS_ULTIPANEL 1
#elif ENABLED(LCD_I2C_VIKI) #elif ENABLED(LCD_I2C_VIKI)
/** /**
@ -416,11 +424,6 @@
#define STD_ENCODER_PULSES_PER_STEP 2 #define STD_ENCODER_PULSES_PER_STEP 2
#define STD_ENCODER_STEPS_PER_MENU_ITEM 1 #define STD_ENCODER_STEPS_PER_MENU_ITEM 1
#elif ANY(IS_RRD_SC, miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864, OLED_PANEL_TINYBOY2, BQ_LCD_SMART_CONTROLLER, LCD_I2C_PANELOLU2)
#define STD_ENCODER_PULSES_PER_STEP 4
#define STD_ENCODER_STEPS_PER_MENU_ITEM 1
#endif #endif
#if EITHER(LCD_I2C_TYPE_MCP23017, LCD_I2C_TYPE_MCP23008) && DISABLED(NO_LCD_DETECT) #if EITHER(LCD_I2C_TYPE_MCP23017, LCD_I2C_TYPE_MCP23008) && DISABLED(NO_LCD_DETECT)

2
Marlin/src/inc/Conditionals_post.h
View File

@ -358,6 +358,8 @@
#define _LCD_CONTRAST_MAX 115 #define _LCD_CONTRAST_MAX 115
#elif ENABLED(VIKI2) #elif ENABLED(VIKI2)
#define _LCD_CONTRAST_INIT 140 #define _LCD_CONTRAST_INIT 140
#elif ENABLED(WYH_L12864)
#define _LCD_CONTRAST_INIT 190
#elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER)
#define _LCD_CONTRAST_MIN 90 #define _LCD_CONTRAST_MIN 90
#define _LCD_CONTRAST_INIT 110 #define _LCD_CONTRAST_INIT 110

3
Marlin/src/inc/SanityCheck.h
View File

@ -855,7 +855,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
/** /**
* LCD Lightweight Screen Style * LCD Lightweight Screen Style
*/ */
#if ENABLED(LIGHTWEIGHT_UI) && DISABLED(U8GLIB_ST7920) #if ENABLED(LIGHTWEIGHT_UI) && !IS_U8GLIB_ST7920
#error "LIGHTWEIGHT_UI requires a U8GLIB_ST7920-based display." #error "LIGHTWEIGHT_UI requires a U8GLIB_ST7920-based display."
#endif #endif
@ -2643,6 +2643,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS
+ COUNT_ENABLED(MKS_TS35_V2_0, MKS_ROBIN_TFT24, MKS_ROBIN_TFT28, MKS_ROBIN_TFT32, MKS_ROBIN_TFT35, MKS_ROBIN_TFT43, MKS_ROBIN_TFT_V1_1R, ANET_ET4_TFT28, ANET_ET5_TFT35, BIQU_BX_TFT70, BTT_TFT35_SPI_V1_0) \ + COUNT_ENABLED(MKS_TS35_V2_0, MKS_ROBIN_TFT24, MKS_ROBIN_TFT28, MKS_ROBIN_TFT32, MKS_ROBIN_TFT35, MKS_ROBIN_TFT43, MKS_ROBIN_TFT_V1_1R, ANET_ET4_TFT28, ANET_ET5_TFT35, BIQU_BX_TFT70, BTT_TFT35_SPI_V1_0) \
+ COUNT_ENABLED(TFTGLCD_PANEL_SPI, TFTGLCD_PANEL_I2C) \ + COUNT_ENABLED(TFTGLCD_PANEL_SPI, TFTGLCD_PANEL_I2C) \
+ COUNT_ENABLED(VIKI2, miniVIKI) \ + COUNT_ENABLED(VIKI2, miniVIKI) \
+ ENABLED(WYH_L12864) \
+ COUNT_ENABLED(ZONESTAR_12864LCD, ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) \ + COUNT_ENABLED(ZONESTAR_12864LCD, ZONESTAR_12864OLED, ZONESTAR_12864OLED_SSD1306) \
+ COUNT_ENABLED(ANET_FULL_GRAPHICS_LCD, ANET_FULL_GRAPHICS_LCD_ALT_WIRING) \ + COUNT_ENABLED(ANET_FULL_GRAPHICS_LCD, ANET_FULL_GRAPHICS_LCD_ALT_WIRING) \
+ ENABLED(AZSMZ_12864) \ + ENABLED(AZSMZ_12864) \

6
Marlin/src/lcd/dogm/marlinui_DOGM.h
View File

@ -43,7 +43,7 @@
#define U8G_PARAM LCD_PINS_D4, LCD_PINS_ENABLE, LCD_PINS_RS #define U8G_PARAM LCD_PINS_D4, LCD_PINS_ENABLE, LCD_PINS_RS
#endif #endif
#elif ENABLED(U8GLIB_ST7920) #elif IS_U8GLIB_ST7920
// RepRap Discount Full Graphics Smart Controller // RepRap Discount Full Graphics Smart Controller
// and other variant LCDs using ST7920 // and other variant LCDs using ST7920
@ -72,7 +72,7 @@
#define U8G_CLASS U8GLIB_DOGM128_2X // 4 stripes (HW-SPI) #define U8G_CLASS U8GLIB_DOGM128_2X // 4 stripes (HW-SPI)
#endif #endif
#elif ENABLED(U8GLIB_LM6059_AF) #elif IS_U8GLIB_LM6059_AF
// Based on the Adafruit ST7565 (https://www.adafruit.com/products/250) // Based on the Adafruit ST7565 (https://www.adafruit.com/products/250)
@ -82,7 +82,7 @@
#define U8G_CLASS U8GLIB_LM6059_2X // 4 stripes (HW-SPI) #define U8G_CLASS U8GLIB_LM6059_2X // 4 stripes (HW-SPI)
#endif #endif
#elif ENABLED(U8GLIB_ST7565_64128N) #elif IS_U8GLIB_ST7565_64128N
// MaKrPanel, Mini Viki, Viki 2.0, AZSMZ 12864 ST7565 controller // MaKrPanel, Mini Viki, Viki 2.0, AZSMZ 12864 ST7565 controller

5
Marlin/src/lcd/dogm/u8g_dev_st7565_64128n_HAL.cpp
View File

@ -63,6 +63,9 @@
#define WIDTH 128 #define WIDTH 128
#define HEIGHT 64 #define HEIGHT 64
#define PAGE_HEIGHT 8 #define PAGE_HEIGHT 8
#ifndef ST7565_XOFFSET
#define ST7565_XOFFSET 0x00
#endif
#define ST7565_ADC_REVERSE(N) ((N) ? 0xA1 : 0xA0) #define ST7565_ADC_REVERSE(N) ((N) ? 0xA1 : 0xA0)
#define ST7565_BIAS_MODE(N) ((N) ? 0xA3 : 0xA2) #define ST7565_BIAS_MODE(N) ((N) ? 0xA3 : 0xA2)
@ -123,7 +126,7 @@ static const uint8_t u8g_dev_st7565_64128n_HAL_init_seq[] PROGMEM = {
static const uint8_t u8g_dev_st7565_64128n_HAL_data_start[] PROGMEM = { static const uint8_t u8g_dev_st7565_64128n_HAL_data_start[] PROGMEM = {
U8G_ESC_ADR(0), // instruction mode U8G_ESC_ADR(0), // instruction mode
U8G_ESC_CS(1), // enable chip U8G_ESC_CS(1), // enable chip
ST7565_COLUMN_ADR(0x00), // high 4 bits to 0, low 4 bits to 0. Changed for DisplayTech 64128N ST7565_COLUMN_ADR(ST7565_XOFFSET), // high 4 bits to 0, low 4 bits to 0. Changed for DisplayTech 64128N
U8G_ESC_END // end of sequence U8G_ESC_END // end of sequence
}; };

4
Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp
View File

@ -29,7 +29,7 @@
#include "../../inc/MarlinConfig.h" #include "../../inc/MarlinConfig.h"
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#include "ultralcd_st7920_u8glib_rrd_AVR.h" #include "ultralcd_st7920_u8glib_rrd_AVR.h"
@ -192,5 +192,5 @@ u8g_dev_t u8g_dev_st7920_128x64_rrd_sw_spi = { u8g_dev_rrd_st7920_128x64_fn, &u8
void ST7920_write_byte(const uint8_t val) { ST7920_WRITE_BYTE(val); } void ST7920_write_byte(const uint8_t val) { ST7920_WRITE_BYTE(val); }
#endif #endif
#endif // U8GLIB_ST7920 #endif // IS_U8GLIB_ST7920
#endif // !U8G_HAL_LINKS && (__AVR__ || ARDUINO_ARCH_STM32 || ARDUINO_ARCH_ESP32) #endif // !U8G_HAL_LINKS && (__AVR__ || ARDUINO_ARCH_STM32 || ARDUINO_ARCH_ESP32)

35
Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_3.h
View File

@ -222,12 +222,13 @@
#error "ANET_FULL_GRAPHICS_LCD_ALT_WIRING only applies to the ANET 1.0 board." #error "ANET_FULL_GRAPHICS_LCD_ALT_WIRING only applies to the ANET 1.0 board."
#elif ENABLED(ANET_FULL_GRAPHICS_LCD) #elif ENABLED(ANET_FULL_GRAPHICS_LCD)
#error "CAUTION! ANET_FULL_GRAPHICS_LCD requires wiring modifications. See 'pins_BTT_SKR_V1_3.h' for details. Comment out this line to continue." #error "CAUTION! ANET_FULL_GRAPHICS_LCD requires wiring modifications. See 'pins_BTT_SKR_V1_3.h' for details. Comment out this line to continue."
/** /**
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way. * 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!) * 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!)
* 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because this pin is open drain.) * 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because it is open drain.)
* 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board. * 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board.
* *
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!! * !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!
@ -254,6 +255,38 @@
#define LCD_PINS_ENABLE EXP1_05_PIN #define LCD_PINS_ENABLE EXP1_05_PIN
#define LCD_PINS_D4 EXP1_07_PIN #define LCD_PINS_D4 EXP1_07_PIN
#elif ENABLED(WYH_L12864)
#error "CAUTION! WYH_L12864 requires wiring modifications. Comment out this line to continue."
/**
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!)
* 3. Swap the LCD's MOSI (Pin9) and empty (Pin10) wires because Pin9 is open drain.
*
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!
*
* The WYH_L12864 connector plug:
*
* BEFORE AFTER
* ______ ______
* GND | 1 2 | 5V 5V | 1 2 | GND
* CS | 3 4 | BTN_EN2 CS | 3 4 | BTN_EN2
* SID | 5 6 BTN_EN1 SID | 5 6 BTN_EN1
* SCK | 7 8 | BTN_ENC SCK | 7 8 | BTN_ENC
* MOSI | 9 10 | open | 9 10 | MOSI
* ------ ------
* LCD LCD
*/
#define BTN_EN1 EXP1_06_PIN
#define BTN_EN2 EXP1_04_PIN
#define BTN_ENC EXP1_08_PIN
#define DOGLCD_CS EXP1_03_PIN
#define DOGLCD_A0 EXP1_05_PIN
#define DOGLCD_SCK EXP1_07_PIN
#define DOGLCD_MOSI EXP1_10_PIN
#define LCD_BACKLIGHT_PIN -1
#elif ENABLED(CR10_STOCKDISPLAY) #elif ENABLED(CR10_STOCKDISPLAY)
#define LCD_PINS_RS EXP1_04_PIN #define LCD_PINS_RS EXP1_04_PIN

2
Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h
View File

@ -323,7 +323,7 @@
/** /**
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way. * 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!) * 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires. (This is the critical part!)
* 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because this pin is open drain.) * 3. Rewire the CLK Signal (LCD Pin9) to LCD Pin7. (LCD Pin9 remains open because it is open drain.)
* 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board. * 4. A wire is needed to connect the Reset switch at J3 (LCD Pin7) to EXP2 (Pin3) on the board.
* *
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!! * !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!

2
Marlin/src/pins/mega/pins_SILVER_GATE.h
View File

@ -73,7 +73,7 @@
#define TEMP_BED_PIN 6 #define TEMP_BED_PIN 6
#if HAS_WIRED_LCD #if HAS_WIRED_LCD
#if ENABLED(U8GLIB_ST7920) // SPI GLCD 12864 ST7920 #if IS_U8GLIB_ST7920 // SPI GLCD 12864 ST7920
#define LCD_PINS_RS 30 #define LCD_PINS_RS 30
#define LCD_PINS_ENABLE 20 #define LCD_PINS_ENABLE 20
#define LCD_PINS_D4 25 #define LCD_PINS_D4 25

2
Marlin/src/pins/pins.h
View File

@ -57,7 +57,7 @@
#define FET_ORDER_EFF 1 #define FET_ORDER_EFF 1
#endif #endif
#if !(BOTH(IS_ULTRA_LCD, IS_NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, MINIPANEL, REPRAPWORLD_KEYPAD)) #if !(BOTH(IS_ULTRA_LCD, IS_NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, WYH_L12864, MINIPANEL, REPRAPWORLD_KEYPAD))
#define HAS_FREE_AUX2_PINS 1 #define HAS_FREE_AUX2_PINS 1
#endif #endif

2
Marlin/src/pins/pins_postprocess.h
View File

@ -1383,7 +1383,7 @@
// //
// Default DOGLCD SPI delays // Default DOGLCD SPI delays
// //
#if DISABLED(U8GLIB_ST7920) #if !IS_U8GLIB_ST7920
#undef ST7920_DELAY_1 #undef ST7920_DELAY_1
#undef ST7920_DELAY_2 #undef ST7920_DELAY_2
#undef ST7920_DELAY_3 #undef ST7920_DELAY_3

2
Marlin/src/pins/rambo/pins_EINSY_RAMBO.h
View File

@ -205,7 +205,7 @@
#endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL #endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/rambo/pins_EINSY_RETRO.h
View File

@ -201,7 +201,7 @@
#endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL || TOUCH_UI_FTDI_EVE #endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL || TOUCH_UI_FTDI_EVE
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/rambo/pins_MINIRAMBO.h
View File

@ -193,7 +193,7 @@
#endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL #endif // HAS_WIRED_LCD || TOUCH_UI_ULTIPANEL
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/rambo/pins_RAMBO.h
View File

@ -270,7 +270,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 0 #define BOARD_ST7920_DELAY_2 0
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/ramps/pins_3DRAG.h
View File

@ -166,7 +166,7 @@
#endif // IS_ULTRA_LCD && IS_NEWPANEL #endif // IS_ULTRA_LCD && IS_NEWPANEL
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 188 #define BOARD_ST7920_DELAY_2 188
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/ramps/pins_BQ_ZUM_MEGA_3D.h
View File

@ -106,7 +106,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 0 #define BOARD_ST7920_DELAY_2 0
#define BOARD_ST7920_DELAY_3 189 #define BOARD_ST7920_DELAY_3 189

2
Marlin/src/pins/ramps/pins_DAGOMA_F5.h
View File

@ -40,7 +40,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 250 #define BOARD_ST7920_DELAY_3 250

2
Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h
View File

@ -182,7 +182,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 200 #define BOARD_ST7920_DELAY_1 200
#define BOARD_ST7920_DELAY_2 200 #define BOARD_ST7920_DELAY_2 200
#define BOARD_ST7920_DELAY_3 200 #define BOARD_ST7920_DELAY_3 200

2
Marlin/src/pins/sanguino/pins_MELZI.h
View File

@ -32,7 +32,7 @@
#define IS_MELZI 1 #define IS_MELZI 1
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#ifndef BOARD_ST7920_DELAY_1 #ifndef BOARD_ST7920_DELAY_1
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#endif #endif

2
Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h
View File

@ -36,7 +36,7 @@
#define BOARD_INFO_NAME "Melzi (Creality)" #define BOARD_INFO_NAME "Melzi (Creality)"
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/sanguino/pins_MELZI_TRONXY.h
View File

@ -28,7 +28,7 @@
#define BOARD_INFO_NAME "Melzi (Tronxy)" #define BOARD_INFO_NAME "Melzi (Tronxy)"
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/sanguino/pins_MELZI_V2.h
View File

@ -28,7 +28,7 @@
#define BOARD_INFO_NAME "Melzi V2" #define BOARD_INFO_NAME "Melzi V2"
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 0 #define BOARD_ST7920_DELAY_1 0
#define BOARD_ST7920_DELAY_2 400 #define BOARD_ST7920_DELAY_2 400
#define BOARD_ST7920_DELAY_3 0 #define BOARD_ST7920_DELAY_3 0

2
Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h
View File

@ -165,7 +165,7 @@
#define KILL_PIN 10 #define KILL_PIN 10
#define BEEPER_PIN 27 #define BEEPER_PIN 27
#elif ENABLED(U8GLIB_ST7920) // SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0 #elif IS_U8GLIB_ST7920 // SPI GLCD 12864 ST7920 ( like [www.digole.com] ) For Melzi V2.0
#if IS_MELZI #if IS_MELZI
#define LCD_PINS_RS 30 // CS chip select /SS chip slave select #define LCD_PINS_RS 30 // CS chip select /SS chip slave select

2
Marlin/src/pins/stm32f1/pins_BTT_SKR_MINI_V1_1.h
View File

@ -202,7 +202,7 @@
#endif // !FYSETC_MINI_12864 #endif // !FYSETC_MINI_12864
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_CCROBOT_MEEB_3DP.h
View File

@ -155,7 +155,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_FLY_MINI.h
View File

@ -179,7 +179,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_GTM32_MINI.h
View File

@ -158,7 +158,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_GTM32_MINI_A30.h
View File

@ -166,7 +166,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_GTM32_PRO_VB.h
View File

@ -163,7 +163,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_GTM32_REV_B.h
View File

@ -168,7 +168,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_E3_common.h
View File

@ -233,7 +233,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#ifndef BOARD_ST7920_DELAY_1 #ifndef BOARD_ST7920_DELAY_1
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#endif #endif

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_LITE.h
View File

@ -113,7 +113,7 @@
#endif // !MKS_MINI_12864 #endif // !MKS_MINI_12864
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_NANO_V2.h
View File

@ -366,7 +366,7 @@
#endif #endif
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_MKS_ROBIN_PRO.h
View File

@ -300,7 +300,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 125 #define BOARD_ST7920_DELAY_2 125
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_ZM3E4_V1_0.h
View File

@ -332,7 +332,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#define BOARD_ST7920_DELAY_2 250 #define BOARD_ST7920_DELAY_2 250
#define BOARD_ST7920_DELAY_3 125 #define BOARD_ST7920_DELAY_3 125

2
Marlin/src/pins/stm32f1/pins_ZM3E4_V2_0.h
View File

@ -305,7 +305,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 200 // Tclk_fall <200ns #define BOARD_ST7920_DELAY_1 200 // Tclk_fall <200ns
#define BOARD_ST7920_DELAY_2 250 // Tdata_width >200ns #define BOARD_ST7920_DELAY_2 250 // Tdata_width >200ns
#define BOARD_ST7920_DELAY_3 200 // Tclk_rise <200ns #define BOARD_ST7920_DELAY_3 200 // Tclk_rise <200ns

2
Marlin/src/pins/stm32f4/pins_BTT_BTT002_V1_0.h
View File

@ -287,7 +287,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 600 #define BOARD_ST7920_DELAY_3 600

2
Marlin/src/pins/stm32f4/pins_BTT_E3_RRF.h
View File

@ -279,7 +279,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 600 #define BOARD_ST7920_DELAY_3 600

4
Marlin/src/pins/stm32f4/pins_BTT_GTR_V1_0.h
View File

@ -483,8 +483,8 @@
// Alter timing for graphical display // Alter timing for graphical display
#if IS_U8GLIB_ST7920 #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 90 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 600 #define BOARD_ST7920_DELAY_3 600
#endif #endif

2
Marlin/src/pins/stm32f4/pins_BTT_OCTOPUS_V1_common.h
View File

@ -493,7 +493,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 120 #define BOARD_ST7920_DELAY_1 120
#define BOARD_ST7920_DELAY_2 80 #define BOARD_ST7920_DELAY_2 80
#define BOARD_ST7920_DELAY_3 580 #define BOARD_ST7920_DELAY_3 580

35
Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h
View File

@ -454,6 +454,39 @@
#define BTN_EN1 EXP2_08_PIN #define BTN_EN1 EXP2_08_PIN
#define BTN_EN2 EXP2_06_PIN #define BTN_EN2 EXP2_06_PIN
#elif ENABLED(WYH_L12864)
#error "CAUTION! WYH_L12864 requires wiring modifications. Comment out this line to continue."
/**
* 1. Cut the tab off the LCD connector so it can be plugged into the "EXP1" connector the other way.
* 2. Swap the LCD's +5V (Pin2) and GND (Pin1) wires.
*
* !!! If you are unsure, ask for help! Your motherboard may be damaged in some circumstances !!!
*
* The WYH_L12864 connector plug:
*
* BEFORE AFTER
* ______ ______
* GND | 1 2 | 5V 5V | 1 2 | GND
* CS | 3 4 | BTN_EN2 CS | 3 4 | BTN_EN2
* SID | 5 6 BTN_EN1 SID | 5 6 BTN_EN1
* SCK | 7 8 | BTN_ENC SCK | 7 8 | BTN_ENC
* MOSI | 9 10 | MOSI | 9 10 |
* ------ ------
* LCD LCD
*/
#undef BEEPER_PIN
#undef BTN_ENC
#define BTN_EN1 EXP1_06_PIN
#define BTN_EN2 EXP1_04_PIN
#define BTN_ENC EXP1_08_PIN
#define DOGLCD_CS EXP1_03_PIN
#define DOGLCD_A0 EXP1_05_PIN
#define DOGLCD_SCK EXP1_07_PIN
#define DOGLCD_MOSI EXP1_09_PIN
#define LCD_BACKLIGHT_PIN -1
#else #else
#define LCD_PINS_RS EXP1_07_PIN #define LCD_PINS_RS EXP1_07_PIN
@ -500,7 +533,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#ifndef BOARD_ST7920_DELAY_1 #ifndef BOARD_ST7920_DELAY_1
#define BOARD_ST7920_DELAY_1 125 #define BOARD_ST7920_DELAY_1 125
#endif #endif

2
Marlin/src/pins/stm32f4/pins_BTT_SKR_V2_0_common.h
View File

@ -482,7 +482,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#ifndef BOARD_ST7920_DELAY_1 #ifndef BOARD_ST7920_DELAY_1
#define BOARD_ST7920_DELAY_1 120 #define BOARD_ST7920_DELAY_1 120
#endif #endif

2
Marlin/src/pins/stm32f4/pins_FLYF407ZG.h
View File

@ -305,7 +305,7 @@
#define FIL_RUNOUT_PIN PA3 #define FIL_RUNOUT_PIN PA3
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715

2
Marlin/src/pins/stm32f4/pins_FYSETC_CHEETAH_V20.h
View File

@ -245,7 +245,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 600 #define BOARD_ST7920_DELAY_3 600

2
Marlin/src/pins/stm32f4/pins_FYSETC_S6.h
View File

@ -314,7 +314,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 640 #define BOARD_ST7920_DELAY_3 640

2
Marlin/src/pins/stm32f4/pins_RUMBA32_common.h
View File

@ -172,7 +172,7 @@
#endif // HAS_WIRED_LCD #endif // HAS_WIRED_LCD
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 640 #define BOARD_ST7920_DELAY_3 640

2
Marlin/src/pins/stm32f4/pins_VAKE403D.h
View File

@ -183,7 +183,7 @@
#endif #endif
// Alter timing for graphical display // Alter timing for graphical display
#if ENABLED(U8GLIB_ST7920) #if IS_U8GLIB_ST7920
#define BOARD_ST7920_DELAY_1 96 #define BOARD_ST7920_DELAY_1 96
#define BOARD_ST7920_DELAY_2 48 #define BOARD_ST7920_DELAY_2 48
#define BOARD_ST7920_DELAY_3 715 #define BOARD_ST7920_DELAY_3 715