Marlin_Firmware/Marlin/stepper.cpp

1298 lines
39 KiB
C++
Raw Normal View History

/**
* stepper.cpp - stepper motor driver: executes motion plans using stepper motors
* Marlin Firmware
*
* Derived from Grbl
* Copyright (c) 2009-2011 Simen Svale Skogsrud
*
* Grbl is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* Grbl is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
2011-11-13 13:42:08 -06:00
/* The timer calculations of this module informed by the 'RepRap cartesian firmware' by Zack Smith
and Philipp Tiefenbacher. */
#include "Marlin.h"
#include "stepper.h"
2011-11-13 13:42:08 -06:00
#include "planner.h"
#include "temperature.h"
#include "ultralcd.h"
#include "language.h"
#include "cardreader.h"
2011-11-13 13:42:08 -06:00
#include "speed_lookuptable.h"
#if HAS_DIGIPOTSS
#include <SPI.h>
2012-11-21 13:53:56 -06:00
#endif
2011-11-13 13:42:08 -06:00
//===========================================================================
//============================= public variables ============================
2011-11-13 13:42:08 -06:00
//===========================================================================
block_t *current_block; // A pointer to the block currently being traced
//===========================================================================
//============================= private variables ===========================
2011-11-13 13:42:08 -06:00
//===========================================================================
2015-02-17 13:37:05 -06:00
//static makes it impossible to be called from outside of this file by extern.!
2011-11-13 13:42:08 -06:00
// Variables used by The Stepper Driver Interrupt
2015-05-17 07:33:09 -05:00
static unsigned char out_bits = 0; // The next stepping-bits to be output
static unsigned int cleaning_buffer_counter;
#ifdef Z_DUAL_ENDSTOPS
static bool performing_homing = false,
locked_z_motor = false,
locked_z2_motor = false;
#endif
2015-04-17 03:28:08 -05:00
// Counter variables for the Bresenham line tracer
static long counter_x, counter_y, counter_z, counter_e;
volatile static unsigned long step_events_completed; // The number of step events executed in the current block
2011-11-13 13:42:08 -06:00
#ifdef ADVANCE
static long advance_rate, advance, final_advance = 0;
2011-12-04 12:54:07 -06:00
static long old_advance = 0;
2015-01-23 16:13:06 -06:00
static long e_steps[4];
2011-11-13 13:42:08 -06:00
#endif
2011-11-13 13:42:08 -06:00
static long acceleration_time, deceleration_time;
//static unsigned long accelerate_until, decelerate_after, acceleration_rate, initial_rate, final_rate, nominal_rate;
2015-04-17 03:28:08 -05:00
static unsigned short acc_step_rate; // needed for deceleration start point
2011-11-13 13:42:08 -06:00
static char step_loops;
static unsigned short OCR1A_nominal;
static unsigned short step_loops_nominal;
2011-11-13 13:42:08 -06:00
volatile long endstops_trigsteps[3] = { 0 };
volatile long endstops_stepsTotal, endstops_stepsDone;
static volatile char endstop_hit_bits = 0; // use X_MIN, Y_MIN, Z_MIN and Z_PROBE as BIT value
2015-05-21 16:16:43 -05:00
#ifndef Z_DUAL_ENDSTOPS
static byte
#else
static uint16_t
#endif
old_endstop_bits = 0; // use X_MIN, X_MAX... Z_MAX, Z_PROBE, Z2_MIN, Z2_MAX
#ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
bool abort_on_endstop_hit = false;
#endif
#ifdef MOTOR_CURRENT_PWM_XY_PIN
int motor_current_setting[3] = DEFAULT_PWM_MOTOR_CURRENT;
#endif
2011-11-13 13:42:08 -06:00
static bool check_endstops = true;
volatile long count_position[NUM_AXIS] = { 0 };
volatile signed char count_direction[NUM_AXIS] = { 1, 1, 1, 1 };
2011-11-13 13:42:08 -06:00
2015-02-26 05:57:46 -06:00
2011-11-13 13:42:08 -06:00
//===========================================================================
//================================ functions ================================
2011-11-13 13:42:08 -06:00
//===========================================================================
#ifdef DUAL_X_CARRIAGE
#define X_APPLY_DIR(v,ALWAYS) \
if (extruder_duplication_enabled || ALWAYS) { \
X_DIR_WRITE(v); \
X2_DIR_WRITE(v); \
} \
else { \
if (current_block->active_extruder) X2_DIR_WRITE(v); else X_DIR_WRITE(v); \
}
#define X_APPLY_STEP(v,ALWAYS) \
if (extruder_duplication_enabled || ALWAYS) { \
X_STEP_WRITE(v); \
X2_STEP_WRITE(v); \
} \
else { \
if (current_block->active_extruder != 0) X2_STEP_WRITE(v); else X_STEP_WRITE(v); \
}
#else
2015-03-14 20:31:25 -05:00
#define X_APPLY_DIR(v,Q) X_DIR_WRITE(v)
#define X_APPLY_STEP(v,Q) X_STEP_WRITE(v)
#endif
#ifdef Y_DUAL_STEPPER_DRIVERS
#define Y_APPLY_DIR(v,Q) { Y_DIR_WRITE(v); Y2_DIR_WRITE((v) != INVERT_Y2_VS_Y_DIR); }
#define Y_APPLY_STEP(v,Q) { Y_STEP_WRITE(v); Y2_STEP_WRITE(v); }
#else
2015-03-14 20:31:25 -05:00
#define Y_APPLY_DIR(v,Q) Y_DIR_WRITE(v)
#define Y_APPLY_STEP(v,Q) Y_STEP_WRITE(v)
#endif
#ifdef Z_DUAL_STEPPER_DRIVERS
#define Z_APPLY_DIR(v,Q) { Z_DIR_WRITE(v); Z2_DIR_WRITE(v); }
#ifdef Z_DUAL_ENDSTOPS
#define Z_APPLY_STEP(v,Q) \
if (performing_homing) { \
if (Z_HOME_DIR > 0) {\
2015-05-21 16:16:43 -05:00
if (!(TEST(old_endstop_bits, Z_MAX) && (count_direction[Z_AXIS] > 0)) && !locked_z_motor) Z_STEP_WRITE(v); \
if (!(TEST(old_endstop_bits, Z2_MAX) && (count_direction[Z_AXIS] > 0)) && !locked_z2_motor) Z2_STEP_WRITE(v); \
} else {\
2015-05-21 16:16:43 -05:00
if (!(TEST(old_endstop_bits, Z_MIN) && (count_direction[Z_AXIS] < 0)) && !locked_z_motor) Z_STEP_WRITE(v); \
if (!(TEST(old_endstop_bits, Z2_MIN) && (count_direction[Z_AXIS] < 0)) && !locked_z2_motor) Z2_STEP_WRITE(v); \
} \
} else { \
Z_STEP_WRITE(v); \
Z2_STEP_WRITE(v); \
}
#else
2015-03-27 19:02:11 -05:00
#define Z_APPLY_STEP(v,Q) { Z_STEP_WRITE(v); Z2_STEP_WRITE(v); }
#endif
#else
2015-03-14 20:31:25 -05:00
#define Z_APPLY_DIR(v,Q) Z_DIR_WRITE(v)
#define Z_APPLY_STEP(v,Q) Z_STEP_WRITE(v)
#endif
2015-03-14 20:31:25 -05:00
#define E_APPLY_STEP(v,Q) E_STEP_WRITE(v)
2011-11-13 13:42:08 -06:00
// intRes = intIn1 * intIn2 >> 16
// uses:
// r26 to store 0
// r27 to store the byte 1 of the 24 bit result
#define MultiU16X8toH16(intRes, charIn1, intIn2) \
asm volatile ( \
"clr r26 \n\t" \
"mul %A1, %B2 \n\t" \
"movw %A0, r0 \n\t" \
"mul %A1, %A2 \n\t" \
"add %A0, r1 \n\t" \
"adc %B0, r26 \n\t" \
"lsr r0 \n\t" \
"adc %A0, r26 \n\t" \
"adc %B0, r26 \n\t" \
"clr r1 \n\t" \
: \
"=&r" (intRes) \
: \
"d" (charIn1), \
"d" (intIn2) \
: \
"r26" \
)
2011-11-13 13:42:08 -06:00
// intRes = longIn1 * longIn2 >> 24
// uses:
// r26 to store 0
// r27 to store bits 16-23 of the 48bit result. The top bit is used to round the two byte result.
// note that the lower two bytes and the upper byte of the 48bit result are not calculated.
// this can cause the result to be out by one as the lower bytes may cause carries into the upper ones.
// B0 A0 are bits 24-39 and are the returned value
// C1 B1 A1 is longIn1
// D2 C2 B2 A2 is longIn2
//
#define MultiU24X32toH16(intRes, longIn1, longIn2) \
asm volatile ( \
"clr r26 \n\t" \
"mul %A1, %B2 \n\t" \
"mov r27, r1 \n\t" \
"mul %B1, %C2 \n\t" \
"movw %A0, r0 \n\t" \
"mul %C1, %C2 \n\t" \
"add %B0, r0 \n\t" \
"mul %C1, %B2 \n\t" \
"add %A0, r0 \n\t" \
"adc %B0, r1 \n\t" \
"mul %A1, %C2 \n\t" \
"add r27, r0 \n\t" \
"adc %A0, r1 \n\t" \
"adc %B0, r26 \n\t" \
"mul %B1, %B2 \n\t" \
"add r27, r0 \n\t" \
"adc %A0, r1 \n\t" \
"adc %B0, r26 \n\t" \
"mul %C1, %A2 \n\t" \
"add r27, r0 \n\t" \
"adc %A0, r1 \n\t" \
"adc %B0, r26 \n\t" \
"mul %B1, %A2 \n\t" \
"add r27, r1 \n\t" \
"adc %A0, r26 \n\t" \
"adc %B0, r26 \n\t" \
"lsr r27 \n\t" \
"adc %A0, r26 \n\t" \
"adc %B0, r26 \n\t" \
"mul %D2, %A1 \n\t" \
"add %A0, r0 \n\t" \
"adc %B0, r1 \n\t" \
"mul %D2, %B1 \n\t" \
"add %B0, r0 \n\t" \
"clr r1 \n\t" \
: \
"=&r" (intRes) \
: \
"d" (longIn1), \
"d" (longIn2) \
: \
"r26" , "r27" \
)
2011-11-13 13:42:08 -06:00
// Some useful constants
#define ENABLE_STEPPER_DRIVER_INTERRUPT() TIMSK1 |= BIT(OCIE1A)
#define DISABLE_STEPPER_DRIVER_INTERRUPT() TIMSK1 &= ~BIT(OCIE1A)
2011-11-13 13:42:08 -06:00
void endstops_hit_on_purpose() {
endstop_hit_bits = 0;
}
2011-11-13 13:42:08 -06:00
void checkHitEndstops() {
2015-05-21 16:16:43 -05:00
if (endstop_hit_bits) {
SERIAL_ECHO_START;
SERIAL_ECHOPGM(MSG_ENDSTOPS_HIT);
if (endstop_hit_bits & BIT(X_MIN)) {
SERIAL_ECHOPAIR(" X:", (float)endstops_trigsteps[X_AXIS] / axis_steps_per_unit[X_AXIS]);
LCD_MESSAGEPGM(MSG_ENDSTOPS_HIT "X");
}
if (endstop_hit_bits & BIT(Y_MIN)) {
SERIAL_ECHOPAIR(" Y:", (float)endstops_trigsteps[Y_AXIS] / axis_steps_per_unit[Y_AXIS]);
LCD_MESSAGEPGM(MSG_ENDSTOPS_HIT "Y");
}
if (endstop_hit_bits & BIT(Z_MIN)) {
SERIAL_ECHOPAIR(" Z:", (float)endstops_trigsteps[Z_AXIS] / axis_steps_per_unit[Z_AXIS]);
LCD_MESSAGEPGM(MSG_ENDSTOPS_HIT "Z");
}
#ifdef Z_PROBE_ENDSTOP
if (endstop_hit_bits & BIT(Z_PROBE)) {
SERIAL_ECHOPAIR(" Z_PROBE:", (float)endstops_trigsteps[Z_AXIS] / axis_steps_per_unit[Z_AXIS]);
LCD_MESSAGEPGM(MSG_ENDSTOPS_HIT "ZP");
}
#endif
SERIAL_EOL;
endstops_hit_on_purpose();
#if defined(ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED) && defined(SDSUPPORT)
if (abort_on_endstop_hit) {
card.sdprinting = false;
card.closefile();
quickStop();
disable_all_heaters(); // switch off all heaters.
}
#endif
}
}
void enable_endstops(bool check) { check_endstops = check; }
2011-11-13 13:42:08 -06:00
// __________________________
// /| |\ _________________ ^
// / | | \ /| |\ |
// / | | \ / | | \ s
// / | | | | | \ p
// / | | | | | \ e
// +-----+------------------------+---+--+---------------+----+ e
// | BLOCK 1 | BLOCK 2 | d
//
// time ----->
//
// The trapezoid is the shape the speed curve over time. It starts at block->initial_rate, accelerates
// first block->accelerate_until step_events_completed, then keeps going at constant speed until
2011-11-13 13:42:08 -06:00
// step_events_completed reaches block->decelerate_after after which it decelerates until the trapezoid generator is reset.
// The slope of acceleration is calculated using v = u + at where t is the accumulated timer values of the steps so far.
2011-11-13 13:42:08 -06:00
void st_wake_up() {
// TCNT1 = 0;
ENABLE_STEPPER_DRIVER_INTERRUPT();
2011-11-13 13:42:08 -06:00
}
2011-11-27 09:45:00 -06:00
FORCE_INLINE unsigned short calc_timer(unsigned short step_rate) {
2011-11-13 13:42:08 -06:00
unsigned short timer;
if (step_rate > MAX_STEP_FREQUENCY) step_rate = MAX_STEP_FREQUENCY;
if (step_rate > 20000) { // If steprate > 20kHz >> step 4 times
step_rate = (step_rate >> 2) & 0x3fff;
2011-11-13 13:42:08 -06:00
step_loops = 4;
}
else if (step_rate > 10000) { // If steprate > 10kHz >> step 2 times
step_rate = (step_rate >> 1) & 0x7fff;
2011-11-13 13:42:08 -06:00
step_loops = 2;
}
else {
step_loops = 1;
}
if (step_rate < (F_CPU / 500000)) step_rate = (F_CPU / 500000);
step_rate -= (F_CPU / 500000); // Correct for minimal speed
if (step_rate >= (8 * 256)) { // higher step rate
2011-11-13 13:42:08 -06:00
unsigned short table_address = (unsigned short)&speed_lookuptable_fast[(unsigned char)(step_rate>>8)][0];
unsigned char tmp_step_rate = (step_rate & 0x00ff);
unsigned short gain = (unsigned short)pgm_read_word_near(table_address+2);
MultiU16X8toH16(timer, tmp_step_rate, gain);
timer = (unsigned short)pgm_read_word_near(table_address) - timer;
}
else { // lower step rates
unsigned short table_address = (unsigned short)&speed_lookuptable_slow[0][0];
table_address += ((step_rate)>>1) & 0xfffc;
timer = (unsigned short)pgm_read_word_near(table_address);
timer -= (((unsigned short)pgm_read_word_near(table_address+2) * (unsigned char)(step_rate & 0x0007))>>3);
}
if (timer < 100) { timer = 100; MYSERIAL.print(MSG_STEPPER_TOO_HIGH); MYSERIAL.println(step_rate); }//(20kHz this should never happen)
2011-11-13 13:42:08 -06:00
return timer;
}
2015-05-17 07:33:09 -05:00
// set the stepper direction of each axis
void set_stepper_direction() {
// Set the direction bits (X_AXIS=A_AXIS and Y_AXIS=B_AXIS for COREXY)
if (TEST(out_bits, X_AXIS)) {
X_APPLY_DIR(INVERT_X_DIR,0);
count_direction[X_AXIS] = -1;
}
else {
X_APPLY_DIR(!INVERT_X_DIR,0);
count_direction[X_AXIS] = 1;
}
if (TEST(out_bits, Y_AXIS)) {
Y_APPLY_DIR(INVERT_Y_DIR,0);
count_direction[Y_AXIS] = -1;
}
else {
Y_APPLY_DIR(!INVERT_Y_DIR,0);
count_direction[Y_AXIS] = 1;
}
if (TEST(out_bits, Z_AXIS)) {
Z_APPLY_DIR(INVERT_Z_DIR,0);
count_direction[Z_AXIS] = -1;
}
else {
Z_APPLY_DIR(!INVERT_Z_DIR,0);
count_direction[Z_AXIS] = 1;
}
#ifndef ADVANCE
if (TEST(out_bits, E_AXIS)) {
REV_E_DIR();
count_direction[E_AXIS] = -1;
}
else {
NORM_E_DIR();
count_direction[E_AXIS] = 1;
}
#endif //!ADVANCE
}
// Initializes the trapezoid generator from the current block. Called whenever a new
2011-11-13 13:42:08 -06:00
// block begins.
2011-11-27 09:45:00 -06:00
FORCE_INLINE void trapezoid_generator_reset() {
2015-05-17 07:33:09 -05:00
if (current_block->direction_bits != out_bits) {
out_bits = current_block->direction_bits;
set_stepper_direction();
}
2011-11-13 13:42:08 -06:00
#ifdef ADVANCE
advance = current_block->initial_advance;
final_advance = current_block->final_advance;
2011-12-04 12:54:07 -06:00
// Do E steps + advance steps
e_steps[current_block->active_extruder] += ((advance >>8) - old_advance);
old_advance = advance >>8;
2011-11-13 13:42:08 -06:00
#endif
deceleration_time = 0;
// step_rate to timer interval
2012-06-11 10:33:42 -05:00
OCR1A_nominal = calc_timer(current_block->nominal_rate);
// make a note of the number of step loops required at nominal speed
step_loops_nominal = step_loops;
2011-11-13 13:42:08 -06:00
acc_step_rate = current_block->initial_rate;
acceleration_time = calc_timer(acc_step_rate);
OCR1A = acceleration_time;
// SERIAL_ECHO_START;
// SERIAL_ECHOPGM("advance :");
// SERIAL_ECHO(current_block->advance/256.0);
// SERIAL_ECHOPGM("advance rate :");
// SERIAL_ECHO(current_block->advance_rate/256.0);
// SERIAL_ECHOPGM("initial advance :");
// SERIAL_ECHO(current_block->initial_advance/256.0);
// SERIAL_ECHOPGM("final advance :");
// SERIAL_ECHOLN(current_block->final_advance/256.0);
2011-11-13 13:42:08 -06:00
}
// "The Stepper Driver Interrupt" - This timer interrupt is the workhorse.
// It pops blocks from the block_buffer and executes them by pulsing the stepper pins appropriately.
ISR(TIMER1_COMPA_vect) {
2015-05-21 16:16:43 -05:00
if (cleaning_buffer_counter)
{
current_block = NULL;
plan_discard_current_block();
#ifdef SD_FINISHED_RELEASECOMMAND
2015-04-12 20:07:08 -05:00
if ((cleaning_buffer_counter == 1) && (SD_FINISHED_STEPPERRELEASE)) enqueuecommands_P(PSTR(SD_FINISHED_RELEASECOMMAND));
#endif
cleaning_buffer_counter--;
OCR1A = 200;
return;
}
2011-11-13 13:42:08 -06:00
// If there is no current block, attempt to pop one from the buffer
if (!current_block) {
2011-11-13 13:42:08 -06:00
// Anything in the buffer?
current_block = plan_get_current_block();
if (current_block) {
current_block->busy = true;
2011-11-13 13:42:08 -06:00
trapezoid_generator_reset();
counter_x = -(current_block->step_event_count >> 1);
counter_y = counter_z = counter_e = counter_x;
step_events_completed = 0;
#ifdef Z_LATE_ENABLE
if (current_block->steps[Z_AXIS] > 0) {
2012-02-06 10:38:16 -06:00
enable_z();
OCR1A = 2000; //1ms wait
return;
}
#endif
// #ifdef ADVANCE
// e_steps[current_block->active_extruder] = 0;
// #endif
}
2011-11-13 13:42:08 -06:00
else {
OCR1A = 2000; // 1kHz.
}
}
2011-11-13 13:42:08 -06:00
if (current_block != NULL) {
2015-05-17 07:33:09 -05:00
// Check endstops
if (check_endstops) {
2015-05-17 07:33:09 -05:00
2015-05-21 16:16:43 -05:00
#ifdef Z_DUAL_ENDSTOPS
uint16_t
#else
byte
#endif
current_endstop_bits;
2015-05-17 07:33:09 -05:00
#define _ENDSTOP_PIN(AXIS, MINMAX) AXIS ##_## MINMAX ##_PIN
#define _ENDSTOP_INVERTING(AXIS, MINMAX) AXIS ##_## MINMAX ##_ENDSTOP_INVERTING
#define _AXIS(AXIS) AXIS ##_AXIS
2015-05-21 16:16:43 -05:00
#define _ENDSTOP_HIT(AXIS) endstop_hit_bits |= BIT(_ENDSTOP(AXIS, MIN))
#define _ENDSTOP(AXIS, MINMAX) AXIS ##_## MINMAX
// SET_ENDSTOP_BIT: set the current endstop bits for an endstop to its status
#define SET_ENDSTOP_BIT(AXIS, MINMAX) SET_BIT(current_endstop_bits, _ENDSTOP(AXIS, MINMAX), (READ(_ENDSTOP_PIN(AXIS, MINMAX)) != _ENDSTOP_INVERTING(AXIS, MINMAX)))
// COPY_BIT: copy the value of COPY_BIT to BIT in bits
#define COPY_BIT(bits, COPY_BIT, BIT) SET_BIT(bits, BIT, TEST(bits, COPY_BIT))
// TEST_ENDSTOP: test the old and the current status of an endstop
#define TEST_ENDSTOP(ENDSTOP) (TEST(current_endstop_bits, ENDSTOP) && TEST(old_endstop_bits, ENDSTOP))
#define UPDATE_ENDSTOP(AXIS,MINMAX) \
SET_ENDSTOP_BIT(AXIS, MINMAX); \
if (TEST_ENDSTOP(_ENDSTOP(AXIS, MINMAX)) && (current_block->steps[_AXIS(AXIS)] > 0)) { \
2015-05-17 07:33:09 -05:00
endstops_trigsteps[_AXIS(AXIS)] = count_position[_AXIS(AXIS)]; \
_ENDSTOP_HIT(AXIS); \
step_events_completed = current_block->step_event_count; \
2015-05-21 16:16:43 -05:00
}
2015-05-17 07:33:09 -05:00
#ifdef COREXY
// Head direction in -X axis for CoreXY bots.
// If DeltaX == -DeltaY, the movement is only in Y axis
if ((current_block->steps[A_AXIS] != current_block->steps[B_AXIS]) || (TEST(out_bits, A_AXIS) == TEST(out_bits, B_AXIS))) {
if (TEST(out_bits, X_HEAD))
#else
2015-04-17 03:28:08 -05:00
if (TEST(out_bits, X_AXIS)) // stepping along -X axis (regular Cartesian bot)
#endif
{ // -direction
#ifdef DUAL_X_CARRIAGE
// with 2 x-carriages, endstops are only checked in the homing direction for the active extruder
if ((current_block->active_extruder == 0 && X_HOME_DIR == -1) || (current_block->active_extruder != 0 && X2_HOME_DIR == -1))
#endif
{
2015-04-03 17:31:35 -05:00
#if HAS_X_MIN
2015-05-21 16:16:43 -05:00
UPDATE_ENDSTOP(X, MIN);
#endif
}
}
else { // +direction
#ifdef DUAL_X_CARRIAGE
// with 2 x-carriages, endstops are only checked in the homing direction for the active extruder
if ((current_block->active_extruder == 0 && X_HOME_DIR == 1) || (current_block->active_extruder != 0 && X2_HOME_DIR == 1))
#endif
{
2015-04-03 17:31:35 -05:00
#if HAS_X_MAX
2015-05-21 16:16:43 -05:00
UPDATE_ENDSTOP(X, MAX);
#endif
}
}
#ifdef COREXY
}
// Head direction in -Y axis for CoreXY bots.
// If DeltaX == DeltaY, the movement is only in X axis
if ((current_block->steps[A_AXIS] != current_block->steps[B_AXIS]) || (TEST(out_bits, A_AXIS) != TEST(out_bits, B_AXIS))) {
if (TEST(out_bits, Y_HEAD))
#else
if (TEST(out_bits, Y_AXIS)) // -direction
#endif
{ // -direction
2015-04-03 17:31:35 -05:00
#if HAS_Y_MIN
2015-05-21 16:16:43 -05:00
UPDATE_ENDSTOP(Y, MIN);
#endif
}
else { // +direction
2015-04-03 17:31:35 -05:00
#if HAS_Y_MAX
2015-05-21 16:16:43 -05:00
UPDATE_ENDSTOP(Y, MAX);
#endif
}
#ifdef COREXY
}
#endif
2015-05-17 07:33:09 -05:00
if (TEST(out_bits, Z_AXIS)) { // z -direction
2015-04-03 17:31:35 -05:00
#if HAS_Z_MIN
#ifdef Z_DUAL_ENDSTOPS
2015-05-21 16:16:43 -05:00
SET_ENDSTOP_BIT(Z, MIN);
#if HAS_Z2_MIN
SET_ENDSTOP_BIT(Z2, MIN);
#else
COPY_BIT(current_endstop_bits, Z_MIN, Z2_MIN);
2015-05-21 16:16:43 -05:00
#endif
byte z_test = TEST_ENDSTOP(Z_MIN) << 0 + TEST_ENDSTOP(Z2_MIN) << 1; // bit 0 for Z, bit 1 for Z2
2015-05-21 16:16:43 -05:00
if (z_test && current_block->steps[Z_AXIS] > 0) { // z_test = Z_MIN || Z2_MIN
endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS];
2015-05-12 02:36:19 -05:00
endstop_hit_bits |= BIT(Z_MIN);
2015-05-31 07:06:13 -05:00
if (!performing_homing || (z_test == 0x3)) //if not performing home or if both endstops were trigged during homing...
step_events_completed = current_block->step_event_count;
}
#else // !Z_DUAL_ENDSTOPS
2015-05-21 16:16:43 -05:00
UPDATE_ENDSTOP(Z, MIN);
#endif // !Z_DUAL_ENDSTOPS
#endif // Z_MIN_PIN
#ifdef Z_PROBE_ENDSTOP
2015-05-21 16:16:43 -05:00
UPDATE_ENDSTOP(Z, PROBE);
if (TEST_ENDSTOP(Z_PROBE))
{
endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS];
2015-05-12 02:33:24 -05:00
endstop_hit_bits |= BIT(Z_PROBE);
}
#endif
2015-05-17 07:33:09 -05:00
}
else { // z +direction
2015-04-03 17:31:35 -05:00
#if HAS_Z_MAX
#ifdef Z_DUAL_ENDSTOPS
2015-05-21 16:16:43 -05:00
SET_ENDSTOP_BIT(Z, MAX);
#if HAS_Z2_MAX
SET_ENDSTOP_BIT(Z2, MAX);
#else
COPY_BIT(current_endstop_bits, Z_MAX, Z2_MAX)
#endif
2015-05-21 16:16:43 -05:00
byte z_test = TEST_ENDSTOP(Z_MAX) << 0 + TEST_ENDSTOP(Z2_MAX) << 1; // bit 0 for Z, bit 1 for Z2
2015-05-21 16:16:43 -05:00
if (z_test && current_block->steps[Z_AXIS] > 0) { // t_test = Z_MAX || Z2_MAX
endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS];
endstop_hit_bits |= BIT(Z_MIN);
2015-05-31 07:06:13 -05:00
if (!performing_homing || (z_test == 0x3)) //if not performing home or if both endstops were trigged during homing...
step_events_completed = current_block->step_event_count;
}
#else // !Z_DUAL_ENDSTOPS
2015-05-21 16:16:43 -05:00
UPDATE_ENDSTOP(Z, MAX);
#endif // !Z_DUAL_ENDSTOPS
#endif // Z_MAX_PIN
2015-05-17 07:33:09 -05:00
#ifdef Z_PROBE_ENDSTOP
2015-05-21 16:16:43 -05:00
UPDATE_ENDSTOP(Z, PROBE);
2015-05-31 07:06:13 -05:00
2015-05-21 16:16:43 -05:00
if (TEST_ENDSTOP(Z_PROBE))
{
endstops_trigsteps[Z_AXIS] = count_position[Z_AXIS];
2015-05-12 02:33:24 -05:00
endstop_hit_bits |= BIT(Z_PROBE);
}
#endif
2015-05-17 07:33:09 -05:00
}
2015-05-21 16:16:43 -05:00
old_endstop_bits = current_endstop_bits;
2015-05-17 07:33:09 -05:00
}
2011-11-13 13:42:08 -06:00
// Take multiple steps per interrupt (For high speed moves)
for (int8_t i = 0; i < step_loops; i++) {
#ifndef AT90USB
MSerial.checkRx(); // Check for serial chars.
#endif
#ifdef ADVANCE
counter_e += current_block->steps[E_AXIS];
if (counter_e > 0) {
counter_e -= current_block->step_event_count;
e_steps[current_block->active_extruder] += TEST(out_bits, E_AXIS) ? -1 : 1;
}
#endif //ADVANCE
#define _COUNTER(axis) counter_## axis
#define _APPLY_STEP(AXIS) AXIS ##_APPLY_STEP
#define _INVERT_STEP_PIN(AXIS) INVERT_## AXIS ##_STEP_PIN
#define STEP_ADD(axis, AXIS) \
_COUNTER(axis) += current_block->steps[_AXIS(AXIS)]; \
if (_COUNTER(axis) > 0) { _APPLY_STEP(AXIS)(!_INVERT_STEP_PIN(AXIS),0); }
STEP_ADD(x,X);
STEP_ADD(y,Y);
STEP_ADD(z,Z);
#ifndef ADVANCE
STEP_ADD(e,E);
#endif
#define STEP_IF_COUNTER(axis, AXIS) \
if (_COUNTER(axis) > 0) { \
_COUNTER(axis) -= current_block->step_event_count; \
count_position[_AXIS(AXIS)] += count_direction[_AXIS(AXIS)]; \
_APPLY_STEP(AXIS)(_INVERT_STEP_PIN(AXIS),0); \
}
STEP_IF_COUNTER(x, X);
STEP_IF_COUNTER(y, Y);
STEP_IF_COUNTER(z, Z);
#ifndef ADVANCE
STEP_IF_COUNTER(e, E);
#endif
2011-11-13 13:42:08 -06:00
step_events_completed++;
if (step_events_completed >= current_block->step_event_count) break;
2011-11-13 13:42:08 -06:00
}
// Calculate new timer value
2011-11-13 13:42:08 -06:00
unsigned short timer;
unsigned short step_rate;
2015-04-12 20:07:08 -05:00
if (step_events_completed <= (unsigned long)current_block->accelerate_until) {
MultiU24X32toH16(acc_step_rate, acceleration_time, current_block->acceleration_rate);
2011-11-13 13:42:08 -06:00
acc_step_rate += current_block->initial_rate;
2011-11-13 13:42:08 -06:00
// upper limit
if (acc_step_rate > current_block->nominal_rate)
2011-11-13 13:42:08 -06:00
acc_step_rate = current_block->nominal_rate;
// step_rate to timer interval
timer = calc_timer(acc_step_rate);
2011-11-25 08:32:50 -06:00
OCR1A = timer;
acceleration_time += timer;
2011-11-13 13:42:08 -06:00
#ifdef ADVANCE
for(int8_t i=0; i < step_loops; i++) {
advance += advance_rate;
}
//if (advance > current_block->advance) advance = current_block->advance;
2011-12-04 12:54:07 -06:00
// Do E steps + advance steps
e_steps[current_block->active_extruder] += ((advance >>8) - old_advance);
old_advance = advance >>8;
2011-11-13 13:42:08 -06:00
#endif
}
2015-04-12 20:07:08 -05:00
else if (step_events_completed > (unsigned long)current_block->decelerate_after) {
MultiU24X32toH16(step_rate, deceleration_time, current_block->acceleration_rate);
if (step_rate > acc_step_rate) { // Check step_rate stays positive
2011-11-13 13:42:08 -06:00
step_rate = current_block->final_rate;
}
else {
step_rate = acc_step_rate - step_rate; // Decelerate from aceleration end point.
}
// lower limit
if (step_rate < current_block->final_rate)
2011-11-13 13:42:08 -06:00
step_rate = current_block->final_rate;
// step_rate to timer interval
timer = calc_timer(step_rate);
2011-11-25 08:32:50 -06:00
OCR1A = timer;
deceleration_time += timer;
2011-11-13 13:42:08 -06:00
#ifdef ADVANCE
for(int8_t i=0; i < step_loops; i++) {
advance -= advance_rate;
}
if (advance < final_advance) advance = final_advance;
2011-12-04 12:54:07 -06:00
// Do E steps + advance steps
e_steps[current_block->active_extruder] += ((advance >>8) - old_advance);
old_advance = advance >>8;
2011-11-13 13:42:08 -06:00
#endif //ADVANCE
}
else {
2011-11-25 08:32:50 -06:00
OCR1A = OCR1A_nominal;
// ensure we're running at the correct step rate, even if we just came off an acceleration
step_loops = step_loops_nominal;
2011-11-13 13:42:08 -06:00
}
// If current block is finished, reset pointer
2011-11-13 13:42:08 -06:00
if (step_events_completed >= current_block->step_event_count) {
current_block = NULL;
plan_discard_current_block();
}
}
2011-11-13 13:42:08 -06:00
}
#ifdef ADVANCE
unsigned char old_OCR0A;
// Timer interrupt for E. e_steps is set in the main routine;
// Timer 0 is shared with millies
ISR(TIMER0_COMPA_vect)
{
2011-12-04 12:54:07 -06:00
old_OCR0A += 52; // ~10kHz interrupt (250000 / 26 = 9615kHz)
OCR0A = old_OCR0A;
2011-11-13 13:42:08 -06:00
// Set E direction (Depends on E direction + advance)
for(unsigned char i=0; i<4;i++) {
if (e_steps[0] != 0) {
E0_STEP_WRITE(INVERT_E_STEP_PIN);
if (e_steps[0] < 0) {
E0_DIR_WRITE(INVERT_E0_DIR);
e_steps[0]++;
E0_STEP_WRITE(!INVERT_E_STEP_PIN);
}
else if (e_steps[0] > 0) {
E0_DIR_WRITE(!INVERT_E0_DIR);
e_steps[0]--;
E0_STEP_WRITE(!INVERT_E_STEP_PIN);
}
}
#if EXTRUDERS > 1
if (e_steps[1] != 0) {
E1_STEP_WRITE(INVERT_E_STEP_PIN);
if (e_steps[1] < 0) {
E1_DIR_WRITE(INVERT_E1_DIR);
e_steps[1]++;
E1_STEP_WRITE(!INVERT_E_STEP_PIN);
}
else if (e_steps[1] > 0) {
E1_DIR_WRITE(!INVERT_E1_DIR);
e_steps[1]--;
E1_STEP_WRITE(!INVERT_E_STEP_PIN);
}
}
#endif
#if EXTRUDERS > 2
if (e_steps[2] != 0) {
E2_STEP_WRITE(INVERT_E_STEP_PIN);
if (e_steps[2] < 0) {
E2_DIR_WRITE(INVERT_E2_DIR);
e_steps[2]++;
E2_STEP_WRITE(!INVERT_E_STEP_PIN);
}
else if (e_steps[2] > 0) {
E2_DIR_WRITE(!INVERT_E2_DIR);
e_steps[2]--;
E2_STEP_WRITE(!INVERT_E_STEP_PIN);
}
}
#endif
2015-01-23 16:13:06 -06:00
#if EXTRUDERS > 3
if (e_steps[3] != 0) {
E3_STEP_WRITE(INVERT_E_STEP_PIN);
2015-01-23 16:13:06 -06:00
if (e_steps[3] < 0) {
E3_DIR_WRITE(INVERT_E3_DIR);
2015-01-23 16:13:06 -06:00
e_steps[3]++;
E3_STEP_WRITE(!INVERT_E_STEP_PIN);
2015-01-23 16:13:06 -06:00
}
else if (e_steps[3] > 0) {
E3_DIR_WRITE(!INVERT_E3_DIR);
2015-01-23 16:13:06 -06:00
e_steps[3]--;
E3_STEP_WRITE(!INVERT_E_STEP_PIN);
2015-01-23 16:13:06 -06:00
}
}
#endif
2011-11-13 13:42:08 -06:00
}
}
#endif // ADVANCE
void st_init() {
digipot_init(); //Initialize Digipot Motor Current
microstep_init(); //Initialize Microstepping Pins
// initialise TMC Steppers
#ifdef HAVE_TMCDRIVER
tmc_init();
#endif
// initialise L6470 Steppers
#ifdef HAVE_L6470DRIVER
L6470_init();
#endif
// Initialize Dir Pins
2015-04-03 17:31:35 -05:00
#if HAS_X_DIR
X_DIR_INIT;
2011-11-13 13:42:08 -06:00
#endif
2015-04-03 17:31:35 -05:00
#if HAS_X2_DIR
X2_DIR_INIT;
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Y_DIR
Y_DIR_INIT;
2015-04-03 17:31:35 -05:00
#if defined(Y_DUAL_STEPPER_DRIVERS) && HAS_Y2_DIR
Y2_DIR_INIT;
#endif
2011-11-13 13:42:08 -06:00
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Z_DIR
Z_DIR_INIT;
2015-04-03 17:31:35 -05:00
#if defined(Z_DUAL_STEPPER_DRIVERS) && HAS_Z2_DIR
Z2_DIR_INIT;
#endif
2011-11-13 13:42:08 -06:00
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E0_DIR
E0_DIR_INIT;
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E1_DIR
E1_DIR_INIT;
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E2_DIR
E2_DIR_INIT;
2011-11-13 13:42:08 -06:00
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E3_DIR
E3_DIR_INIT;
2015-01-23 16:13:06 -06:00
#endif
2011-11-13 13:42:08 -06:00
//Initialize Enable Pins - steppers default to disabled.
2015-04-03 17:31:35 -05:00
#if HAS_X_ENABLE
X_ENABLE_INIT;
if (!X_ENABLE_ON) X_ENABLE_WRITE(HIGH);
2011-11-13 13:42:08 -06:00
#endif
2015-04-03 17:31:35 -05:00
#if HAS_X2_ENABLE
X2_ENABLE_INIT;
if (!X_ENABLE_ON) X2_ENABLE_WRITE(HIGH);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Y_ENABLE
Y_ENABLE_INIT;
if (!Y_ENABLE_ON) Y_ENABLE_WRITE(HIGH);
#if defined(Y_DUAL_STEPPER_DRIVERS) && HAS_Y2_ENABLE
Y2_ENABLE_INIT;
if (!Y_ENABLE_ON) Y2_ENABLE_WRITE(HIGH);
#endif
2011-11-13 13:42:08 -06:00
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Z_ENABLE
Z_ENABLE_INIT;
if (!Z_ENABLE_ON) Z_ENABLE_WRITE(HIGH);
2015-04-03 17:31:35 -05:00
#if defined(Z_DUAL_STEPPER_DRIVERS) && HAS_Z2_ENABLE
Z2_ENABLE_INIT;
if (!Z_ENABLE_ON) Z2_ENABLE_WRITE(HIGH);
#endif
2011-11-13 13:42:08 -06:00
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E0_ENABLE
E0_ENABLE_INIT;
if (!E_ENABLE_ON) E0_ENABLE_WRITE(HIGH);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E1_ENABLE
E1_ENABLE_INIT;
if (!E_ENABLE_ON) E1_ENABLE_WRITE(HIGH);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E2_ENABLE
E2_ENABLE_INIT;
if (!E_ENABLE_ON) E2_ENABLE_WRITE(HIGH);
2011-11-13 13:42:08 -06:00
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E3_ENABLE
E3_ENABLE_INIT;
if (!E_ENABLE_ON) E3_ENABLE_WRITE(HIGH);
2015-01-23 16:13:06 -06:00
#endif
2011-11-13 13:42:08 -06:00
//endstops and pullups
2015-04-03 17:31:35 -05:00
#if HAS_X_MIN
SET_INPUT(X_MIN_PIN);
#ifdef ENDSTOPPULLUP_XMIN
2011-11-13 13:42:08 -06:00
WRITE(X_MIN_PIN,HIGH);
#endif
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Y_MIN
SET_INPUT(Y_MIN_PIN);
#ifdef ENDSTOPPULLUP_YMIN
2011-11-13 13:42:08 -06:00
WRITE(Y_MIN_PIN,HIGH);
#endif
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Z_MIN
SET_INPUT(Z_MIN_PIN);
#ifdef ENDSTOPPULLUP_ZMIN
2011-11-13 13:42:08 -06:00
WRITE(Z_MIN_PIN,HIGH);
#endif
#endif
2015-04-03 17:31:35 -05:00
#if HAS_X_MAX
SET_INPUT(X_MAX_PIN);
#ifdef ENDSTOPPULLUP_XMAX
WRITE(X_MAX_PIN,HIGH);
2011-11-13 13:42:08 -06:00
#endif
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Y_MAX
SET_INPUT(Y_MAX_PIN);
#ifdef ENDSTOPPULLUP_YMAX
WRITE(Y_MAX_PIN,HIGH);
2011-11-13 13:42:08 -06:00
#endif
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Z_MAX
SET_INPUT(Z_MAX_PIN);
#ifdef ENDSTOPPULLUP_ZMAX
WRITE(Z_MAX_PIN,HIGH);
2011-11-13 13:42:08 -06:00
#endif
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Z2_MAX
SET_INPUT(Z2_MAX_PIN);
#ifdef ENDSTOPPULLUP_ZMAX
WRITE(Z2_MAX_PIN,HIGH);
#endif
#endif
2015-05-17 07:33:09 -05:00
#if (defined(Z_PROBE_PIN) && Z_PROBE_PIN >= 0) && defined(Z_PROBE_ENDSTOP) // Check for Z_PROBE_ENDSTOP so we don't pull a pin high unless it's to be used.
SET_INPUT(Z_PROBE_PIN);
#ifdef ENDSTOPPULLUP_ZPROBE
WRITE(Z_PROBE_PIN,HIGH);
#endif
#endif
#define _STEP_INIT(AXIS) AXIS ##_STEP_INIT
#define _WRITE_STEP(AXIS, HIGHLOW) AXIS ##_STEP_WRITE(HIGHLOW)
#define _DISABLE(axis) disable_## axis()
#define AXIS_INIT(axis, AXIS, PIN) \
_STEP_INIT(AXIS); \
_WRITE_STEP(AXIS, _INVERT_STEP_PIN(PIN)); \
_DISABLE(axis)
2011-11-13 13:42:08 -06:00
#define E_AXIS_INIT(NUM) AXIS_INIT(e## NUM, E## NUM, E)
// Initialize Step Pins
2015-04-03 17:31:35 -05:00
#if HAS_X_STEP
AXIS_INIT(x, X, X);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_X2_STEP
AXIS_INIT(x, X2, X);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Y_STEP
#if defined(Y_DUAL_STEPPER_DRIVERS) && HAS_Y2_STEP
Y2_STEP_INIT;
Y2_STEP_WRITE(INVERT_Y_STEP_PIN);
#endif
AXIS_INIT(y, Y, Y);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_Z_STEP
#if defined(Z_DUAL_STEPPER_DRIVERS) && HAS_Z2_STEP
Z2_STEP_INIT;
Z2_STEP_WRITE(INVERT_Z_STEP_PIN);
#endif
AXIS_INIT(z, Z, Z);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E0_STEP
E_AXIS_INIT(0);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E1_STEP
E_AXIS_INIT(1);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E2_STEP
E_AXIS_INIT(2);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_E3_STEP
E_AXIS_INIT(3);
2015-01-23 16:13:06 -06:00
#endif
2011-11-13 13:42:08 -06:00
// waveform generation = 0100 = CTC
TCCR1B &= ~BIT(WGM13);
TCCR1B |= BIT(WGM12);
TCCR1A &= ~BIT(WGM11);
TCCR1A &= ~BIT(WGM10);
2011-11-13 13:42:08 -06:00
// output mode = 00 (disconnected)
TCCR1A &= ~(3<<COM1A0);
TCCR1A &= ~(3<<COM1B0);
// Set the timer pre-scaler
// Generally we use a divider of 8, resulting in a 2MHz timer
// frequency on a 16MHz MCU. If you are going to change this, be
// sure to regenerate speed_lookuptable.h with
// create_speed_lookuptable.py
TCCR1B = (TCCR1B & ~(0x07<<CS10)) | (2<<CS10);
2011-11-13 13:42:08 -06:00
OCR1A = 0x4000;
2011-11-18 11:59:17 -06:00
TCNT1 = 0;
ENABLE_STEPPER_DRIVER_INTERRUPT();
2011-11-13 13:42:08 -06:00
#ifdef ADVANCE
#if defined(TCCR0A) && defined(WGM01)
TCCR0A &= ~BIT(WGM01);
TCCR0A &= ~BIT(WGM00);
#endif
e_steps[0] = e_steps[1] = e_steps[2] = e_steps[3] = 0;
TIMSK0 |= BIT(OCIE0A);
2011-11-13 13:42:08 -06:00
#endif //ADVANCE
enable_endstops(true); // Start with endstops active. After homing they can be disabled
2011-11-13 13:42:08 -06:00
sei();
2015-05-17 07:33:09 -05:00
set_stepper_direction(); // Init directions to out_bits = 0
2011-11-13 13:42:08 -06:00
}
2015-05-26 22:08:21 -05:00
/**
* Block until all buffered steps are executed
*/
void st_synchronize() { while (blocks_queued()) idle(); }
2011-11-20 07:50:08 -06:00
void st_set_position(const long &x, const long &y, const long &z, const long &e) {
2011-11-20 07:50:08 -06:00
CRITICAL_SECTION_START;
count_position[X_AXIS] = x;
count_position[Y_AXIS] = y;
count_position[Z_AXIS] = z;
count_position[E_AXIS] = e;
CRITICAL_SECTION_END;
}
void st_set_e_position(const long &e) {
CRITICAL_SECTION_START;
count_position[E_AXIS] = e;
CRITICAL_SECTION_END;
}
long st_get_position(uint8_t axis) {
2011-11-20 07:50:08 -06:00
long count_pos;
CRITICAL_SECTION_START;
count_pos = count_position[axis];
CRITICAL_SECTION_END;
return count_pos;
}
#ifdef ENABLE_AUTO_BED_LEVELING
float st_get_position_mm(AxisEnum axis) {
return st_get_position(axis) / axis_steps_per_unit[axis];
}
#endif // ENABLE_AUTO_BED_LEVELING
void finishAndDisableSteppers() {
st_synchronize();
disable_all_steppers();
}
void quickStop() {
cleaning_buffer_counter = 5000;
DISABLE_STEPPER_DRIVER_INTERRUPT();
while (blocks_queued()) plan_discard_current_block();
current_block = NULL;
ENABLE_STEPPER_DRIVER_INTERRUPT();
}
#ifdef BABYSTEPPING
// MUST ONLY BE CALLED BY AN ISR,
// No other ISR should ever interrupt this!
void babystep(const uint8_t axis, const bool direction) {
#define _ENABLE(axis) enable_## axis()
#define _READ_DIR(AXIS) AXIS ##_DIR_READ
#define _INVERT_DIR(AXIS) INVERT_## AXIS ##_DIR
#define _APPLY_DIR(AXIS, INVERT) AXIS ##_APPLY_DIR(INVERT, true)
#define BABYSTEP_AXIS(axis, AXIS, INVERT) { \
_ENABLE(axis); \
uint8_t old_pin = _READ_DIR(AXIS); \
_APPLY_DIR(AXIS, _INVERT_DIR(AXIS)^direction^INVERT); \
_APPLY_STEP(AXIS)(!_INVERT_STEP_PIN(AXIS), true); \
2015-04-16 06:16:36 -05:00
delayMicroseconds(2); \
_APPLY_STEP(AXIS)(_INVERT_STEP_PIN(AXIS), true); \
_APPLY_DIR(AXIS, old_pin); \
}
switch(axis) {
case X_AXIS:
BABYSTEP_AXIS(x, X, false);
break;
case Y_AXIS:
BABYSTEP_AXIS(y, Y, false);
break;
case Z_AXIS: {
#ifndef DELTA
BABYSTEP_AXIS(z, Z, BABYSTEP_INVERT_Z);
#else // DELTA
bool z_direction = direction ^ BABYSTEP_INVERT_Z;
enable_x();
enable_y();
enable_z();
uint8_t old_x_dir_pin = X_DIR_READ,
old_y_dir_pin = Y_DIR_READ,
old_z_dir_pin = Z_DIR_READ;
//setup new step
X_DIR_WRITE(INVERT_X_DIR^z_direction);
Y_DIR_WRITE(INVERT_Y_DIR^z_direction);
Z_DIR_WRITE(INVERT_Z_DIR^z_direction);
//perform step
X_STEP_WRITE(!INVERT_X_STEP_PIN);
Y_STEP_WRITE(!INVERT_Y_STEP_PIN);
Z_STEP_WRITE(!INVERT_Z_STEP_PIN);
2015-04-16 06:16:36 -05:00
delayMicroseconds(2);
X_STEP_WRITE(INVERT_X_STEP_PIN);
Y_STEP_WRITE(INVERT_Y_STEP_PIN);
Z_STEP_WRITE(INVERT_Z_STEP_PIN);
//get old pin state back.
X_DIR_WRITE(old_x_dir_pin);
Y_DIR_WRITE(old_y_dir_pin);
Z_DIR_WRITE(old_z_dir_pin);
#endif
} break;
default: break;
}
}
#endif //BABYSTEPPING
// From Arduino DigitalPotControl example
void digitalPotWrite(int address, int value) {
#if HAS_DIGIPOTSS
digitalWrite(DIGIPOTSS_PIN,LOW); // take the SS pin low to select the chip
SPI.transfer(address); // send in the address and value via SPI:
SPI.transfer(value);
digitalWrite(DIGIPOTSS_PIN,HIGH); // take the SS pin high to de-select the chip:
//delay(10);
#endif
}
// Initialize Digipot Motor Current
void digipot_init() {
#if HAS_DIGIPOTSS
const uint8_t digipot_motor_current[] = DIGIPOT_MOTOR_CURRENT;
SPI.begin();
pinMode(DIGIPOTSS_PIN, OUTPUT);
for (int i = 0; i <= 4; i++) {
//digitalPotWrite(digipot_ch[i], digipot_motor_current[i]);
digipot_current(i,digipot_motor_current[i]);
}
#endif
#ifdef MOTOR_CURRENT_PWM_XY_PIN
pinMode(MOTOR_CURRENT_PWM_XY_PIN, OUTPUT);
pinMode(MOTOR_CURRENT_PWM_Z_PIN, OUTPUT);
pinMode(MOTOR_CURRENT_PWM_E_PIN, OUTPUT);
digipot_current(0, motor_current_setting[0]);
digipot_current(1, motor_current_setting[1]);
digipot_current(2, motor_current_setting[2]);
//Set timer5 to 31khz so the PWM of the motor power is as constant as possible. (removes a buzzing noise)
TCCR5B = (TCCR5B & ~(_BV(CS50) | _BV(CS51) | _BV(CS52))) | _BV(CS50);
#endif
}
void digipot_current(uint8_t driver, int current) {
#if HAS_DIGIPOTSS
const uint8_t digipot_ch[] = DIGIPOT_CHANNELS;
digitalPotWrite(digipot_ch[driver], current);
#endif
#ifdef MOTOR_CURRENT_PWM_XY_PIN
switch(driver) {
case 0: analogWrite(MOTOR_CURRENT_PWM_XY_PIN, 255L * current / MOTOR_CURRENT_PWM_RANGE); break;
case 1: analogWrite(MOTOR_CURRENT_PWM_Z_PIN, 255L * current / MOTOR_CURRENT_PWM_RANGE); break;
case 2: analogWrite(MOTOR_CURRENT_PWM_E_PIN, 255L * current / MOTOR_CURRENT_PWM_RANGE); break;
}
#endif
}
void microstep_init() {
2015-04-03 17:31:35 -05:00
#if HAS_MICROSTEPS_E1
pinMode(E1_MS1_PIN,OUTPUT);
2015-04-03 17:31:35 -05:00
pinMode(E1_MS2_PIN,OUTPUT);
#endif
2015-04-03 17:31:35 -05:00
#if HAS_MICROSTEPS
pinMode(X_MS1_PIN,OUTPUT);
pinMode(X_MS2_PIN,OUTPUT);
pinMode(Y_MS1_PIN,OUTPUT);
pinMode(Y_MS2_PIN,OUTPUT);
pinMode(Z_MS1_PIN,OUTPUT);
pinMode(Z_MS2_PIN,OUTPUT);
pinMode(E0_MS1_PIN,OUTPUT);
pinMode(E0_MS2_PIN,OUTPUT);
2015-03-27 02:32:58 -05:00
const uint8_t microstep_modes[] = MICROSTEP_MODES;
for (uint16_t i = 0; i < sizeof(microstep_modes) / sizeof(microstep_modes[0]); i++)
2015-03-27 02:32:58 -05:00
microstep_mode(i, microstep_modes[i]);
#endif
}
void microstep_ms(uint8_t driver, int8_t ms1, int8_t ms2) {
if (ms1 >= 0) switch(driver) {
case 0: digitalWrite(X_MS1_PIN, ms1); break;
case 1: digitalWrite(Y_MS1_PIN, ms1); break;
case 2: digitalWrite(Z_MS1_PIN, ms1); break;
case 3: digitalWrite(E0_MS1_PIN, ms1); break;
2015-04-03 17:31:35 -05:00
#if HAS_MICROSTEPS_E1
case 4: digitalWrite(E1_MS1_PIN, ms1); break;
#endif
}
if (ms2 >= 0) switch(driver) {
case 0: digitalWrite(X_MS2_PIN, ms2); break;
case 1: digitalWrite(Y_MS2_PIN, ms2); break;
case 2: digitalWrite(Z_MS2_PIN, ms2); break;
case 3: digitalWrite(E0_MS2_PIN, ms2); break;
#if defined(E1_MS2_PIN) && E1_MS2_PIN >= 0
case 4: digitalWrite(E1_MS2_PIN, ms2); break;
#endif
}
}
void microstep_mode(uint8_t driver, uint8_t stepping_mode) {
switch(stepping_mode) {
case 1: microstep_ms(driver,MICROSTEP1); break;
case 2: microstep_ms(driver,MICROSTEP2); break;
case 4: microstep_ms(driver,MICROSTEP4); break;
case 8: microstep_ms(driver,MICROSTEP8); break;
case 16: microstep_ms(driver,MICROSTEP16); break;
}
}
void microstep_readings() {
SERIAL_PROTOCOLPGM("MS1,MS2 Pins\n");
SERIAL_PROTOCOLPGM("X: ");
SERIAL_PROTOCOL(digitalRead(X_MS1_PIN));
SERIAL_PROTOCOLLN(digitalRead(X_MS2_PIN));
SERIAL_PROTOCOLPGM("Y: ");
SERIAL_PROTOCOL(digitalRead(Y_MS1_PIN));
SERIAL_PROTOCOLLN(digitalRead(Y_MS2_PIN));
SERIAL_PROTOCOLPGM("Z: ");
SERIAL_PROTOCOL(digitalRead(Z_MS1_PIN));
SERIAL_PROTOCOLLN(digitalRead(Z_MS2_PIN));
SERIAL_PROTOCOLPGM("E0: ");
SERIAL_PROTOCOL(digitalRead(E0_MS1_PIN));
SERIAL_PROTOCOLLN(digitalRead(E0_MS2_PIN));
2015-04-03 17:31:35 -05:00
#if HAS_MICROSTEPS_E1
SERIAL_PROTOCOLPGM("E1: ");
SERIAL_PROTOCOL(digitalRead(E1_MS1_PIN));
SERIAL_PROTOCOLLN(digitalRead(E1_MS2_PIN));
#endif
}
#ifdef Z_DUAL_ENDSTOPS
void In_Homing_Process(bool state) { performing_homing = state; }
void Lock_z_motor(bool state) { locked_z_motor = state; }
void Lock_z2_motor(bool state) { locked_z2_motor = state; }
#endif