Marlin_Firmware/Marlin/src/pins/pins_AZTEEG_X3_PRO.h

177 lines
4.8 KiB
C
Raw Normal View History

/**
2016-03-24 13:01:20 -05:00
* Marlin 3D Printer Firmware
2019-02-12 15:06:53 -06:00
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
2016-03-24 13:01:20 -05:00
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* AZTEEG_X3_PRO (Arduino Mega) pin assignments
*/
#ifndef __AVR_ATmega2560__
#error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
#endif
#if HOTENDS > 5 || E_STEPPERS > 5
#error "Azteeg X3 Pro supports up to 5 hotends / E-steppers. Comment out this line to continue."
#endif
#define BOARD_NAME "Azteeg X3 Pro"
//
// RAMPS pins overrides
//
2018-03-28 12:51:59 -05:00
#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT)
#define CASE_LIGHT_PIN 44
2017-04-07 13:52:21 -05:00
#endif
#ifndef FAN_PIN
#define FAN_PIN 6
#endif
2016-07-30 05:10:30 -05:00
#include "pins_RAMPS.h"
2018-02-17 21:24:04 -06:00
// DIGIPOT slave addresses
2018-03-28 12:51:59 -05:00
#define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT 0x2C (0x58 <- 0x2C << 1)
#define DIGIPOT_I2C_ADDRESS_B 0x2E // unshifted slave address for second DIGIPOT 0x2E (0x5C <- 0x2E << 1)
//
// Servos
//
// Tested this pin with bed leveling on a Delta with 1 servo.
// Physical wire attachment on EXT1: GND, 5V, D47.
//
#undef SERVO0_PIN
#define SERVO0_PIN 47
//
// Limit Switches
//
// Swap the MIN and MAX endstop pins because the X3 Pro comes with only
// MIN endstop pin headers soldered onto the board.
//
#if ENABLED(DELTA)
#undef X_MIN_PIN
#undef X_MAX_PIN
#undef Y_MIN_PIN
#undef Y_MAX_PIN
#undef Z_MIN_PIN
#undef Z_MAX_PIN
2015-04-06 00:34:56 -05:00
#define X_MIN_PIN 2
#define X_MAX_PIN 3
#define Y_MIN_PIN 15
#define Y_MAX_PIN 14
#define Z_MIN_PIN 19
#define Z_MAX_PIN 18
#endif
//
// Z Probe (when not Z_MIN_PIN)
//
#ifndef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN 18
#endif
//
// Steppers
//
#define E2_STEP_PIN 23
#define E2_DIR_PIN 25
#define E2_ENABLE_PIN 40
#define E3_STEP_PIN 27
#define E3_DIR_PIN 29
#define E3_ENABLE_PIN 41
#define E4_STEP_PIN 43
#define E4_DIR_PIN 37
#define E4_ENABLE_PIN 42
//
// Temperature Sensors
//
#define TEMP_2_PIN 12 // Analog Input
#define TEMP_3_PIN 11 // Analog Input
#define TEMP_4_PIN 10 // Analog Input
#define TC1 4 // Analog Input (Thermo couple on Azteeg X3Pro)
#define TC2 5 // Analog Input (Thermo couple on Azteeg X3Pro)
//
// Heaters / Fans
//
#define HEATER_2_PIN 16
#define HEATER_3_PIN 17
#define HEATER_4_PIN 4
#define HEATER_5_PIN 5
#define HEATER_6_PIN 6
#define HEATER_7_PIN 11
#ifndef CONTROLLER_FAN_PIN
2018-03-28 12:51:59 -05:00
#define CONTROLLER_FAN_PIN 4 // Pin used for the fan to cool motherboard (-1 to disable)
#endif
// Fans/Water Pump to cool the hotend cool side.
#define ORIG_E0_AUTO_FAN_PIN 5
#define ORIG_E1_AUTO_FAN_PIN 5
#define ORIG_E2_AUTO_FAN_PIN 5
#define ORIG_E3_AUTO_FAN_PIN 5
//
// LCD / Controller
//
#undef BEEPER_PIN
#define BEEPER_PIN 33
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#undef SD_DETECT_PIN
2017-06-08 18:08:03 -05:00
#define SD_DETECT_PIN 49 // For easy adapter board
2017-04-07 13:52:21 -05:00
#undef BEEPER_PIN
2018-03-28 12:51:59 -05:00
#define BEEPER_PIN 12 // 33 isn't physically available to the LCD display
#else
2017-10-09 16:18:10 -05:00
#define STAT_LED_RED_PIN 32
2016-09-24 16:26:41 -05:00
#define STAT_LED_BLUE_PIN 35
#endif
2017-04-07 13:52:21 -05:00
//
// Misc. Functions
//
2017-06-04 11:30:03 -05:00
#if ENABLED(CASE_LIGHT_ENABLE) && PIN_EXISTS(CASE_LIGHT) && defined(DOGLCD_A0) && DOGLCD_A0 == CASE_LIGHT_PIN
2018-03-28 12:51:59 -05:00
#undef DOGLCD_A0 // Steal pin 44 for the case light; if you have a Viki2 and have connected it
#define DOGLCD_A0 57 // following the Panucatt wiring diagram, you may need to tweak these pin assignments
// as the wiring diagram uses pin 44 for DOGLCD_A0
2017-04-07 13:52:21 -05:00
#endif
//
// M3/M4/M5 - Spindle/Laser Control
//
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are no good with the AzteegX3pro board
2017-04-07 13:52:21 -05:00
#undef SPINDLE_LASER_ENABLE_PIN
#undef SPINDLE_DIR_PIN
2018-03-28 12:51:59 -05:00
#if ENABLED(SPINDLE_LASER_ENABLE) // EXP2 header
2017-04-07 13:52:21 -05:00
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
#undef BTN_EN2
2018-03-28 12:51:59 -05:00
#define BTN_EN2 31 // need 7 for the spindle speed PWM
2017-04-07 13:52:21 -05:00
#endif
2018-03-28 12:51:59 -05:00
#define SPINDLE_LASER_PWM_PIN 7 // must have a hardware PWM
#define SPINDLE_LASER_ENABLE_PIN 20 // Pin should have a pullup!
2017-04-07 13:52:21 -05:00
#define SPINDLE_DIR_PIN 21
#endif