Marlin_Firmware/Marlin/pins_3DRAG.h

164 lines
4.4 KiB
C
Raw Normal View History

/**
2016-03-24 13:01:20 -05:00
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* 3DRAG (and K8200 / K8400) Arduino Mega with RAMPS v1.4 pin assignments
*/
#ifndef BOARD_NAME
#define BOARD_NAME "3Drag"
#endif
#ifndef DEFAULT_MACHINE_NAME
#define DEFAULT_MACHINE_NAME "3Drag"
#endif
#ifndef DEFAULT_SOURCE_CODE_URL
#define DEFAULT_SOURCE_CODE_URL "http://3dprint.elettronicain.it/"
#endif
//
// Heaters / Fans
//
#define RAMPS_D8_PIN 9
#define RAMPS_D9_PIN 8
#define MOSFET_D_PIN 12
2017-04-07 13:52:21 -05:00
#define CASE_LIGHT_PIN -1 // MUST BE HARDWARE PWM but one is not available on expansion header
2016-07-30 05:10:30 -05:00
#include "pins_RAMPS.h"
//
// Limit Switches
//
#undef Z_MAX_PIN
#define Z_MAX_PIN -1
//
// Steppers
//
#undef Z_ENABLE_PIN
#define Z_ENABLE_PIN 63
//
// Heaters / Fans
//
#define HEATER_2_PIN 6
//
// Misc. Functions
//
#undef SDSS
#define SDSS 25
#undef SD_DETECT_PIN
#define SD_DETECT_PIN 53
//
// LCD / Controller
//
#if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)
#undef BEEPER_PIN
#define BEEPER_PIN -1
#undef LCD_PINS_RS
#undef LCD_PINS_ENABLE
#undef LCD_PINS_D4
#undef LCD_PINS_D5
#undef LCD_PINS_D6
#undef LCD_PINS_D7
#define LCD_PINS_RS 27
#define LCD_PINS_ENABLE 29
#define LCD_PINS_D4 37
#define LCD_PINS_D5 35
#define LCD_PINS_D6 33
#define LCD_PINS_D7 31
// Buttons
#undef BTN_EN1
#undef BTN_EN2
#undef BTN_ENC
#define BTN_EN1 16
#define BTN_EN2 17
#define BTN_ENC 23
#else
#define BEEPER_PIN 33
#endif // ULTRA_LCD && NEWPANEL
2017-04-07 13:52:21 -05:00
/**
* M3/M4/M5 - Spindle/Laser Control
*
* If you want to control the speed of your spindle then you'll have
* have to sacrifce the Extruder and pull some signals off the Z stepper
* driver socket.
*
* The following assumes:
* - the Z stepper driver socket is empty
* - the extruder driver socket has a driver board plugged into it
* - the Z stepper wires are attached the the extruder connector
*
* If you want to keep the extruder AND don't have a LCD display then
* you can still control the power on/off and spindle direction.
*
* Where to get spindle signals
*
* stepper signal socket name socket name
* -------
* SPINDLE_LASER_ENABLE_PIN /ENABLE O| |O VMOT
* MS1 O| |O GND
* MS2 O| |O 2B
* MS3 O| |O 2A
* /RESET O| |O 1A
* /SLEEP O| |O 1B
* SPINDLE_LASER_PWM_PIN STEP O| |O VDD
* SPINDLE_DIR_PIN DIR O| |O GND
* -------
*
* Note: Socket names vary from vendor to vendor
*/
#undef SPINDLE_LASER_PWM_PIN // Definitions in pins_RAMPS.h are not good with 3DRAG
#undef SPINDLE_LASER_ENABLE_PIN
#undef SPINDLE_DIR_PIN
#if ENABLED(SPINDLE_LASER_ENABLE)
#if !EXTRUDERS
#undef E0_DIR_PIN
#undef E0_ENABLE_PIN
#undef E0_STEP_PIN
#undef Z_DIR_PIN
#undef Z_ENABLE_PIN
#undef Z_STEP_PIN
#define Z_DIR_PIN 28
#define Z_ENABLE_PIN 24
#define Z_STEP_PIN 26
#define SPINDLE_LASER_PWM_PIN 46 // MUST BE HARDWARE PWM
#define SPINDLE_LASER_ENABLE_PIN 62 // Pin should have a pullup!
#define SPINDLE_DIR_PIN 48
#elif !(ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL)) // use expansion header if no LCD in use
#define SPINDLE_LASER_ENABLE_PIN 16 // Pin should have a pullup/pulldown!
#define SPINDLE_DIR_PIN 17
#endif
#endif