Marlin_Firmware/Marlin/src/pins/lpc1768/pins_BTT_SKR_common.h

/**
 * Marlin 3D Printer Firmware
 * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
 *
 * Based on Sprinter and grbl.
 * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
 *
 * This program is free software: you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <https://www.gnu.org/licenses/>.
 *
 */
#pragma once

#ifdef SKR_HAS_LPC1769
  #if NOT_TARGET(MCU_LPC1769)
    #error "Oops! Make sure you have the LPC1769 environment selected in your IDE."
  #endif
#elif NOT_TARGET(MCU_LPC1768)
  #error "Oops! Make sure you have the LPC1768 environment selected in your IDE."
#endif

// Ignore temp readings during development.
//#define BOGUS_TEMPERATURE_GRACE_PERIOD    2000

//
// Steppers
//
#ifndef E1_STEP_PIN
  #define E1_STEP_PIN                      P0_01
#endif
#ifndef E1_DIR_PIN
  #define E1_DIR_PIN                       P0_00
#endif
#ifndef E1_ENABLE_PIN
  #define E1_ENABLE_PIN                    P0_10
#endif

//
// Temperature Sensors
//  3.3V max when defined as an analog input
//
#ifndef TEMP_0_PIN
  #define TEMP_0_PIN                    P0_24_A1  // A1 (T1) - (68) - TEMP_0_PIN
#endif
#ifndef TEMP_1_PIN
  #define TEMP_1_PIN                    P0_25_A2  // A2 (T2) - (69) - TEMP_1_PIN
#endif
#ifndef TEMP_BED_PIN
  #define TEMP_BED_PIN                  P0_23_A0  // A0 (T0) - (67) - TEMP_BED_PIN
#endif

#if HOTENDS == 1
  #if TEMP_SENSOR_PROBE
    #define TEMP_PROBE_PIN            TEMP_1_PIN
  #elif TEMP_SENSOR_CHAMBER
    #define TEMP_CHAMBER_PIN          TEMP_1_PIN
  #endif
#endif

//
// Heaters / Fans
//
#ifndef HEATER_0_PIN
  #define HEATER_0_PIN                     P2_07
#endif
#if HOTENDS == 1
  #ifndef FAN1_PIN
    #define FAN1_PIN                       P2_04
  #endif
#else
  #ifndef HEATER_1_PIN
    #define HEATER_1_PIN                   P2_04
  #endif
#endif
#ifndef FAN_PIN
  #define FAN_PIN                          P2_03
#endif
#ifndef HEATER_BED_PIN
  #define HEATER_BED_PIN                   P2_05
#endif

//
// LCD / Controller
//
#if HAS_WIRED_LCD && DISABLED(LCD_USE_I2C_BUZZER)
  #define BEEPER_PIN                       P1_30  // (37) not 5V tolerant
#endif

//
// SD Support
//
#define ONBOARD_SD_CS_PIN                  P0_06  // Chip select for "System" SD card

#if SD_CONNECTION_IS(LCD)
  #define SCK_PIN                          P0_15
  #define MISO_PIN                         P0_17
  #define MOSI_PIN                         P0_18
#elif SD_CONNECTION_IS(ONBOARD)
  #undef SD_DETECT_PIN
  #define SD_DETECT_PIN                    P0_27
  #define SCK_PIN                          P0_07
  #define MISO_PIN                         P0_08
  #define MOSI_PIN                         P0_09
  #define SS_PIN               ONBOARD_SD_CS_PIN
#elif SD_CONNECTION_IS(CUSTOM_CABLE)
  #error "No custom SD drive cable defined for this board."
#endif