Marlin_Firmware/Marlin/scripts/createTemperatureLookupMarlin.py

#!/usr/bin/python
"""Thermistor Value Lookup Table Generator

Generates lookup to temperature values for use in a microcontroller in C format based on: 
http://en.wikipedia.org/wiki/Steinhart-Hart_equation

The main use is for Arduino programs that read data from the circuit board described here:
http://make.rrrf.org/ts-1.0

Usage: python createTemperatureLookup.py [options]

Options:
  -h, --help        show this help
  --rp=...          pull-up resistor
  --t1=ttt:rrr      low temperature temperature:resistance point (around 25 degC)
  --t2=ttt:rrr      middle temperature temperature:resistance point (around 150 degC)
  --t3=ttt:rrr      high temperature temperature:resistance point (around 250 degC)
  --num-temps=...   the number of temperature points to calculate (default: 36)
"""

from math import *
import sys
import getopt

"Constants"
ZERO   = 273.15                             # zero point of Kelvin scale
VADC   = 5                                  # ADC voltage
VCC    = 5                                  # supply voltage
ARES   = pow(2,10)                          # 10 Bit ADC resolution
VSTEP  = VADC / ARES                        # ADC voltage resolution
TMIN   = 0                                  # lowest temperature in table
TMAX   = 350                                # highest temperature in table

class Thermistor:
    "Class to do the thermistor maths"
    def __init__(self, rp, t1, r1, t2, r2, t3, r3):
        l1 = log(r1)
        l2 = log(r2)
        l3 = log(r3)
        y1 = 1.0 / (t1 + ZERO)              # adjust scale
        y2 = 1.0 / (t2 + ZERO)
        y3 = 1.0 / (t3 + ZERO)
        x = (y2 - y1) / (l2 - l1)
        y = (y3 - y1) / (l3 - l1)
        c = (y - x) / ((l3 - l2) * (l1 + l2 + l3))
        b = x - c * (pow(l1,2) + pow(l2,2) + l1*l2)
        a = y1 - (b + pow(l1,2)*c)*l1
        self.c1 = a                         # Steinhart-Hart coefficients
        self.c2 = b
        self.c3 = c
        self.rp = rp                        # pull-up resistance

    def resol(self, adc):
        "Convert ADC reading into a resolution"
        res = self.temp(adc)-self.temp(adc+1)
        return res

    def voltage(self, adc):
        "Convert ADC reading into a Voltage"
        return adc * VSTEP                     # convert the 10 bit ADC value to a voltage

    def resist(self, adc):
        "Convert ADC reading into a resistance in Ohms"
        r = self.rp * self.voltage(adc) / (VCC - self.voltage(adc)) # resistance of thermistor
        return r

    def temp(self, adc):
        "Convert ADC reading into a temperature in Celcius"
        l = log(self.resist(adc))
        Tinv = self.c1 + self.c2*l + self.c3*pow(l,3) # inverse temperature
        return (1/Tinv) - ZERO              # temperature

    def adc(self, temp):
        "Convert temperature into a ADC reading"
        x = (self.c1 - (1.0 / (temp+ZERO))) / (2*self.c3)
        y = sqrt(pow(self.c2 / (3*self.c3),3) + pow(x,2))
        r = exp(pow(y-x,1.0/3) - pow(y+x,1.0/3)) # resistance of thermistor
        return (r / (self.rp + r)) * ARES

def main(argv):
    "Default values"
    t1 = 25                                 # low temperature in Kelvin (25 degC)
    r1 = 100000                             # resistance at low temperature (10 kOhm)
    t2 = 150                                # middle temperature in Kelvin (150 degC)
    r2 = 1641.9                             # resistance at middle temperature (1.6 KOhm)
    t3 = 250                                # high temperature in Kelvin (250 degC)
    r3 = 226.15                             # resistance at high temperature (226.15 Ohm)
    rp = 4700;                              # pull-up resistor (4.7 kOhm)
    num_temps = 36;                         # number of entries for look-up table
    
    try:
        opts, args = getopt.getopt(argv, "h", ["help", "rp=", "t1=", "t2=", "t3=", "num-temps="])
    except getopt.GetoptError as err:
        print  str(err)
        usage()
        sys.exit(2)

    for opt, arg in opts:
        if opt in ("-h", "--help"):
            usage()
            sys.exit()
        elif opt == "--rp":
            rp = int(arg)
        elif opt == "--t1":
            arg =  arg.split(':')
            t1 = float(arg[0])
            r1 = float(arg[1])
        elif opt == "--t2":
            arg =  arg.split(':')
            t2 = float(arg[0])
            r2 = float(arg[1])
        elif opt == "--t3":
            arg =  arg.split(':')
            t3 = float(arg[0])
            r3 = float(arg[1])
        elif opt == "--num-temps":
            num_temps =  int(arg)

    increment = int((ARES-1)/(num_temps-1));
    t = Thermistor(rp, t1, r1, t2, r2, t3, r3)
    tmp = (TMIN-TMAX) / (num_temps-1)
    temps = range(TMAX, TMIN+tmp, tmp);

    print "// Thermistor lookup table for Marlin"
    print "// ./createTemperatureLookupMarlin.py --rp=%s --t1=%s:%s --t2=%s:%s --t3=%s:%s --num-temps=%s" % (rp, t1, r1, t2, r2, t3, r3, num_temps)
    print "// Steinhart-Hart Coefficients: a=%.15g, b=%.15g, c=%.15g " % (t.c1, t.c2, t.c3)
    print
    print "#define NUMTEMPS %s" % (len(temps))
    print "const short temptable[NUMTEMPS][2] PROGMEM = {"

    for temp in temps:
        adc = t.adc(temp)
        print "    { (short) (%7.2f * OVERSAMPLENR ), %4s }%s // v=%.3f\tr=%.3f\tres=%.3f degC/count" % (adc , temp, \
                        ',' if temp != temps[-1] else ' ', \
                        t.voltage(adc), \
                        t.resist( adc), \
                        t.resol(  adc) \
                    )
    print "};"

def usage():
    print __doc__

if __name__ == "__main__":
    main(sys.argv[1:])