Marlin_Firmware/Marlin/pins_RIGIDBOARD.h

/**
 * RIGIDBOARD Arduino Mega with RAMPS v1.4 pin assignments
 */

#include "pins_RAMPS_14.h"

#if ENABLED(Z_MIN_PROBE_ENDSTOP)
  #undef Z_MAX_PIN
  #define Z_MAX_PIN -1
  #undef Z_MIN_PROBE_PIN
  #define Z_MIN_PROBE_PIN  19    // Z-MAX pin J14 End Stops
#endif

#undef HEATER_0_PIN
#undef HEATER_1_PIN
#define HEATER_0_PIN        9    // EXTRUDER 1
#define HEATER_1_PIN       12    // EXTRUDER 2 (FAN On Sprinter)

#undef TEMP_0_PIN
#undef TEMP_1_PIN
#define TEMP_0_PIN         14   // ANALOG NUMBERING
#define TEMP_1_PIN         13   // ANALOG NUMBERING

// LCD Panel options for the RigidBoard

#if ENABLED(RIGIDBOT_PANEL)

  #undef BEEPER_PIN
  #define BEEPER_PIN -1

  // Direction buttons
  #define BTN_UP           37
  #define BTN_DWN          35
  #define BTN_LFT          33
  #define BTN_RT           32

  // 'R' button
  #undef  BTN_ENC
  #define BTN_ENC 31

  // Disable encoder
  #undef  BTN_EN1
  #define BTN_EN1 -1
  #undef  BTN_EN2
  #define BTN_EN2 -1

  #undef  SD_DETECT_PIN
  #define SD_DETECT_PIN 22

#elif ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)

  #undef BEEPER_PIN
  #define BEEPER_PIN -1

  #undef  SD_DETECT_PIN
  #define SD_DETECT_PIN 22

  #undef  KILL_PIN
  #define KILL_PIN 32

#endif

// SPI for Max6675 Thermocouple
#undef MAX6675_SS
#if ENABLED(SDSUPPORT)
  #define MAX6675_SS       49 // Don't use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
#else
  #define MAX6675_SS       53 // Don't use pin 53 if there is even the remote possibility of using Display/SD card
#endif

// RigidBot swaps E0 / E1 plugs vs RAMPS 1.3

#undef E0_STEP_PIN
#undef E0_DIR_PIN
#undef E0_ENABLE_PIN
#define E0_STEP_PIN        36
#define E0_DIR_PIN         34
#define E0_ENABLE_PIN      30

#undef E1_STEP_PIN
#undef E1_DIR_PIN
#undef E1_ENABLE_PIN
#define E1_STEP_PIN        26
#define E1_DIR_PIN         28
#define E1_ENABLE_PIN      24

#undef  FAN_PIN
#define FAN_PIN             8 // Same as RAMPS_13_EEF

#undef  PS_ON_PIN
#define PS_ON_PIN          -1

#undef  HEATER_BED_PIN
#define HEATER_BED_PIN     10

#undef  TEMP_BED_PIN
#define TEMP_BED_PIN       15   // ANALOG NUMBERING

#define STEPPER_RESET_PIN  41   // Stepper drivers have a reset on RigidBot
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00			`/**`
Base RAMPS-like boards on RAMPS 1.4 2016-02-29 01:13:50 -06:00			`* RIGIDBOARD Arduino Mega with RAMPS v1.4 pin assignments`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00			`*/`

Base RAMPS-like boards on RAMPS 1.4 2016-02-29 01:13:50 -06:00			`#include "pins_RAMPS_14.h"`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00
Make Z_PROBE a Z_MIN_PROBE (PR#65) Currently we use the probe exclusively as a device to find the build platform(bed). For the currently supported setups this means, we use it as a additional min-endstop. A triggered when not deployed probe disturbs the homing process for max-endstops. Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP Adjust comments accordingly Remove Z_MAX check for the probe in update_endstops(). Using an delta related idea of @clefranc from #61, extended to the general change for all setups. Tested with Prusa i3, max-z-endstop and permanently triggered z-probe. Worked for @clefranc's delta. 2015-08-10 03:35:39 -05:00			`#if ENABLED(Z_MIN_PROBE_ENDSTOP)`
Fixing Rigidbot LCD Panel Support 2015-12-12 19:57:36 -06:00			`#undef Z_MAX_PIN`
			`#define Z_MAX_PIN -1`
			`#undef Z_MIN_PROBE_PIN`
			`#define Z_MIN_PROBE_PIN 19 // Z-MAX pin J14 End Stops`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00			`#endif`

			`#undef HEATER_0_PIN`
			`#undef HEATER_1_PIN`
			`#define HEATER_0_PIN 9 // EXTRUDER 1`
			`#define HEATER_1_PIN 12 // EXTRUDER 2 (FAN On Sprinter)`

			`#undef TEMP_0_PIN`
			`#undef TEMP_1_PIN`
			`#define TEMP_0_PIN 14 // ANALOG NUMBERING`
			`#define TEMP_1_PIN 13 // ANALOG NUMBERING`

			`// LCD Panel options for the RigidBoard`

Overridable Options - Part 4 (PR#2556) Apply `ENABLED` / `DISABLED` / `HAS_SERVOS` macros to pins files. 2015-07-31 00:11:19 -05:00			`#if ENABLED(RIGIDBOT_PANEL)`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 2015-07-31 01:19:11 -05:00			`#undef BEEPER_PIN`
			`#define BEEPER_PIN -1`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00
Fixing Rigidbot LCD Panel Support 2015-12-12 19:57:36 -06:00			`// Direction buttons`
			`#define BTN_UP 37`
			`#define BTN_DWN 35`
			`#define BTN_LFT 33`
			`#define BTN_RT 32`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00
Fixing Rigidbot LCD Panel Support 2015-12-12 19:57:36 -06:00			`// 'R' button`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00			`#undef BTN_ENC`
			`#define BTN_ENC 31`

Fixing Rigidbot LCD Panel Support 2015-12-12 19:57:36 -06:00			`// Disable encoder`
			`#undef BTN_EN1`
			`#define BTN_EN1 -1`
			`#undef BTN_EN2`
			`#define BTN_EN2 -1`

SDCARDDETECT -> SD_DETECT, added docs - `SD_DETECT_PIN` replaces `SDCARDDETECT` - `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED` - Revise the description of `SD_DETECT_INVERTED` - Add a note about the override of `SD_DETECT_INVERTED` in `Conditionals.h` 2015-07-31 18:40:50 -05:00			`#undef SD_DETECT_PIN`
			`#define SD_DETECT_PIN 22`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00
Apply remaining ENABLED/DISABLED conditionals 2015-08-03 14:30:37 -05:00			`#elif ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00
Rename BEEPER to BEEPER_PIN For consistency with other pins, allowing use of `PIN_EXISTS` macro. 2015-07-31 01:19:11 -05:00			`#undef BEEPER_PIN`
			`#define BEEPER_PIN -1`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00
SDCARDDETECT -> SD_DETECT, added docs - `SD_DETECT_PIN` replaces `SDCARDDETECT` - `SD_DETECT_INVERTED` replaces `SDCARDDETECTINVERTED` - Revise the description of `SD_DETECT_INVERTED` - Add a note about the override of `SD_DETECT_INVERTED` in `Conditionals.h` 2015-07-31 18:40:50 -05:00			`#undef SD_DETECT_PIN`
			`#define SD_DETECT_PIN 22`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00
			`#undef KILL_PIN`
			`#define KILL_PIN 32`

			`#endif`

			`// SPI for Max6675 Thermocouple`
			`#undef MAX6675_SS`
Apply remaining ENABLED/DISABLED conditionals 2015-08-03 14:30:37 -05:00			`#if ENABLED(SDSUPPORT)`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00			`#define MAX6675_SS 49 // Don't use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present`
Apply remaining ENABLED/DISABLED conditionals 2015-08-03 14:30:37 -05:00			`#else`
			`#define MAX6675_SS 53 // Don't use pin 53 if there is even the remote possibility of using Display/SD card`
RIGIDBOARD / RIGIDPANEL 2015-07-08 17:08:15 -05:00			`#endif`

			`// RigidBot swaps E0 / E1 plugs vs RAMPS 1.3`

			`#undef E0_STEP_PIN`
			`#undef E0_DIR_PIN`
			`#undef E0_ENABLE_PIN`
			`#define E0_STEP_PIN 36`
			`#define E0_DIR_PIN 34`
			`#define E0_ENABLE_PIN 30`

			`#undef E1_STEP_PIN`
			`#undef E1_DIR_PIN`
			`#undef E1_ENABLE_PIN`
			`#define E1_STEP_PIN 26`
			`#define E1_DIR_PIN 28`
			`#define E1_ENABLE_PIN 24`

			`#undef FAN_PIN`
			`#define FAN_PIN 8 // Same as RAMPS_13_EEF`

			`#undef PS_ON_PIN`
			`#define PS_ON_PIN -1`

			`#undef HEATER_BED_PIN`
			`#define HEATER_BED_PIN 10`

			`#undef TEMP_BED_PIN`
			`#define TEMP_BED_PIN 15 // ANALOG NUMBERING`

			`#define STEPPER_RESET_PIN 41 // Stepper drivers have a reset on RigidBot`