Marlin_Firmware/Marlin/src/pins/stm32/pins_JGAURORA_A5S_A1.h

130 lines
3.1 KiB
C
Raw Normal View History

/**
* Marlin 3D Printer Firmware
* Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
2019-06-27 23:57:50 -05:00
* Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
2019-07-04 22:44:12 -05:00
#pragma once
/**
* 2017 Victor Perez Marlin for stm32f1 test
* 2018 Modified by Pablo Crespo for Morpheus Board (https://github.com/pscrespo/Morpheus-STM32)
* 2019 Modified by Roberto Mariani & Samuel Pinches for JGAurora A5S & A1 Board.
*/
/**
* JGAurora A5S A1 Board pin assignments
*/
#ifndef __STM32F1__
#error "Oops! Select an STM32F1 board in 'Tools > Board.'"
#endif
#define BOARD_NAME "JGAurora A5S A1 board"
// #define STM32_XL_DENSITY // required, but should be set by platformio flags, not here! (why? not sure.)
//#define MCU_STM32F103ZE // not yet required
2019-07-09 21:26:35 -05:00
// #define I2C_EEPROM // AT24C64
// #define E2END 0x7FFF // 64KB
// Enable EEPROM Emulation for this board
//#define FLASH_EEPROM_EMULATION 1
2019-07-09 21:26:35 -05:00
//#define E2END 0xFFF // 4KB
//#define E2END uint32(EEPROM_START_ADDRESS + (EEPROM_PAGE_SIZE * 2) - 1)
//#define EEPROM_CHITCHAT
//#define DEBUG_EEPROM_READWRITE
//
// Limit Switches
//
#define X_STOP_PIN PC6
#define Y_STOP_PIN PG8
#define Z_STOP_PIN PG7
//
// Steppers
//
#define X_STEP_PIN PD6
#define X_DIR_PIN PD3
#define X_ENABLE_PIN PG9
#define Y_STEP_PIN PG12
#define Y_DIR_PIN PG11
#define Y_ENABLE_PIN PG13
#define Z_STEP_PIN PG15
#define Z_DIR_PIN PG14
#define Z_ENABLE_PIN PB8
#define E0_STEP_PIN PE2
#define E0_DIR_PIN PB9
#define E0_ENABLE_PIN PE3
#define E1_STEP_PIN PE5
#define E1_DIR_PIN PE4
#define E1_ENABLE_PIN PE6
//
// Temperature Sensors
//
#define TEMP_0_PIN PC2
#define TEMP_BED_PIN PC1
//
// Heaters / Fans
//
#define HEATER_0_PIN PA2
#define HEATER_BED_PIN PA3
#define FAN_PIN PA1
#define PS_ON_PIN PA0
#define FIL_RUNOUT_PIN PC7
//
// LCD
//
#define LCD_BACKLIGHT_PIN PF11
#define FSMC_CS_PIN PD7
#define FSMC_RS_PIN PG0
//
// SD Card
//
#define SD_DETECT_PIN PF10
//
// Misc.
//
#define BEEPER_PIN PC3 // use PB7 to shut up if desired
#define LED_PIN PC13
//
// Touch support
//
#if ENABLED(TOUCH_BUTTONS)
#define BTN_ENC PA11 // Real pin needed to enable encoder's push button functionality used by touch screen. PA11 gives stable value.
#define TOUCH_CS_PIN PA4
#define TOUCH_INT_PIN PC4
#endif
#define NO_PAUSE_AFTER_PRINT