Marlin_Firmware/buildroot/share/tests/LPC1768-tests

#!/usr/bin/env bash
#
# Build tests for LPC1768 (NXP ARM Cortex-M3)
#

# exit on first failure
set -e

restore_configs
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EFB
exec_test $1 $2 "Build Re-ARM Default Configuration"

restore_configs
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EFB
opt_enable VIKI2 SDSUPPORT
opt_enable SERIAL_PORT2
opt_enable NEOPIXEL_LED
opt_set NEOPIXEL_PIN P1_16
exec_test $1 $2 "ReARM EFB VIKI2, SDSUPPORT, 2 Serial ports (USB CDC + UART0), NeoPixel"

restore_configs
use_example_configs Mks/Sbase
exec_test $1 $2 "MKS SBASE Example Config"

restore_configs
opt_set MOTHERBOARD BOARD_MKS_SBASE
opt_set EXTRUDERS 2
opt_set TEMP_SENSOR_1 1
opt_set NUM_SERVOS 2
opt_set SERVO_DELAY "{ 300, 300 }"
opt_enable SWITCHING_NOZZLE SWITCHING_NOZZLE_E1_SERVO_NR ULTIMAKERCONTROLLER
exec_test $1 $2 "MKS_SBASE SWITCHING_NOZZLE"

restore_configs
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EEB
opt_set EXTRUDERS 2
opt_set TEMP_SENSOR_1 -1
opt_set TEMP_SENSOR_BED 5
opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER SDSUPPORT ADAPTIVE_FAN_SLOWING NO_FAN_SLOWING_IN_PID_TUNING \
           FILAMENT_WIDTH_SENSOR FILAMENT_LCD_DISPLAY \
           FIX_MOUNTED_PROBE Z_SAFE_HOMING AUTO_BED_LEVELING_BILINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE \
           BABYSTEPPING BABYSTEP_XY BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \
           PRINTCOUNTER NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE SLOW_PWM_HEATERS PIDTEMPBED EEPROM_SETTINGS INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT \
           ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE \
           LCD_INFO_MENU ARC_SUPPORT BEZIER_CURVE_SUPPORT EXTENDED_CAPABILITIES_REPORT AUTO_REPORT_TEMPERATURES SDCARD_SORT_ALPHA
opt_set GRID_MAX_POINTS_X 16
exec_test $1 $2 "MKS SBASE Many Features"

restore_configs
opt_set MOTHERBOARD BOARD_RAMPS_14_RE_ARM_EFB
opt_enable COREYX USE_XMAX_PLUG DAC_MOTOR_CURRENT_DEFAULT \
           REPRAP_DISCOUNT_SMART_CONTROLLER SDSUPPORT BABYSTEPPING \
           AUTO_BED_LEVELING_UBL RESTORE_LEVELING_AFTER_G28 EEPROM_SETTINGS \
           FILAMENT_LCD_DISPLAY FILAMENT_WIDTH_SENSOR FAN_SOFT_PWM \
           SHOW_TEMP_ADC_VALUES HOME_Y_BEFORE_X EMERGENCY_PARSER FAN_KICKSTART_TIME \
           ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED ADVANCED_OK \
           VOLUMETRIC_DEFAULT_ON NO_WORKSPACE_OFFSETS ACTION_ON_KILL \
           EXTRA_FAN_SPEED FWRETRACT Z_DUAL_STEPPER_DRIVERS Z_DUAL_ENDSTOPS \
           MENU_ADDAUTOSTART SDCARD_SORT_ALPHA
opt_set FAN_MIN_PWM 50
opt_set FAN_KICKSTART_TIME 100
opt_set XY_FREQUENCY_LIMIT  15
exec_test $1 $2 "MKS SBASE Many less common options"

# clean up
restore_configs