Marlin_Firmware/buildroot/share/PlatformIO/variants/MARLIN_F407VE/variant.h

220 lines
7.1 KiB
C
Raw Normal View History

/*
*******************************************************************************
* Copyright (c) 2017, STMicroelectronics
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*******************************************************************************
*/
#ifndef _VARIANT_ARDUINO_STM32_
#define _VARIANT_ARDUINO_STM32_
/*----------------------------------------------------------------------------
* Headers
*----------------------------------------------------------------------------*/
#include "PeripheralPins.h"
#ifdef __cplusplus
extern "C" {
#endif // __cplusplus
/*----------------------------------------------------------------------------
* Pins
*----------------------------------------------------------------------------*/
extern const PinName digitalPin[];
// Right Side
#define PE1 0
#define PE0 1
#define PB9 2
#define PB8 3
#define PB7 4
#define PB6 5
#define PB5 6
#define PB3 7
#define PD7 8
#define PD6 9
#define PD5 10
#define PD4 11
#define PD3 12
#define PD2 13
#define PD1 14
#define PD0 15
#define PC12 16
#define PC11 17
#define PC10 18
#define PA15 19
#define PA12 20 // USB_DP
#define PA11 21 // USB_DM
#define PA10 22
#define PA9 23
#define PA8 24
#define PC9 25
#define PC8 26
#define PC7 27
#define PC6 28
#define PD15 29
#define PD14 30
#define PD13 31
#define PD12 32
#define PD11 33
#define PD10 34
#define PD9 35
#define PD8 36
#define PB15 37
// Left Side
#define PE2 38
#define PE3 39
#define PE4 40 // BUT K0
#define PE5 41 // BUT K1
#define PE6 42
#define PC13 43
#define PC0 44 // A0
#define PC1 45 // A1
#define PC2 46 // A2
#define PC3 47 // A3
#define PA0 48 // A4/WK_UP: BUT K_UP
#define PA1 49 // A5
#define PA2 50 // A6
#define PA3 51 // A7
#define PA4 52 // A8
#define PA5 53 // A9
#define PC4 54 // A10
#define PC5 55 // A11
#define PB0 56 // A12
#define PB1 57 // A13
#define PA6 58 // LED D2
#define PA7 59 // LED D3 (active LOW)
#define PE7 60
#define PE8 61
#define PE9 62
#define PE10 63
#define PE11 64
#define PE12 65
#define PE13 66
#define PE14 67
#define PE15 68
#define PB10 69
#define PB11 70
#define PB12 71
#define PB13 72
#define PB14 73
#define PB4 74
// This must be a literal
#define NUM_DIGITAL_PINS 75
// This must be a literal with a value less than or equal to MAX_ANALOG_INPUTS
#define NUM_ANALOG_INPUTS 14
#define NUM_ANALOG_FIRST 44
// Below ADC, DAC and PWM definitions already done in the core
// Could be redefined here if needed
// ADC resolution is 12bits
//#define ADC_RESOLUTION 12
//#define DACC_RESOLUTION 12
// PWM resolution
#define PWM_RESOLUTION 8
#define PWM_FREQUENCY 20000
#define PWM_MAX_DUTY_CYCLE 255
// On-board LED pin number
#define LED_D2 PA6
#define LED_D3 PA7
// Board specific button
#define BTN_K_UP PA0
#define LED_BUILTIN LED_D2
#define LED_GREEN LED_D2
// On-board user button
#define BTN_K0 PE4
#define BTN_K1 PE3
#define USER_BTN BTN_K0
// Below SPI and I2C definitions already done in the core
// Could be redefined here if differs from the default one
// SPI Definitions
#define PIN_SPI_MOSI PB15
#define PIN_SPI_MISO PB14
#define PIN_SPI_SCK PB13
#define PIN_SPI_SS PB12
//#define PIN_SPI_SS1 PB0 // W25Q16 (on board flash)
// I2C Definitions
#define PIN_WIRE_SDA PB7
#define PIN_WIRE_SCL PB6
// Timer Definitions
//Do not use timer used by PWM pins when possible. See PinMap_PWM in PeripheralPins.c
#define TIMER_TONE TIM6
// Do not use basic timer: OC is required
#define TIMER_SERVO TIM2 //TODO: advanced-control timers don't work
// UART Definitions
// Define here Serial instance number to map on Serial generic name
#define SERIAL_UART_INSTANCE 1 //ex: 2 for Serial2 (USART2)
// DEBUG_UART could be redefined to print on another instance than 'Serial'
//#define DEBUG_UART ((USART_TypeDef *) U(S)ARTX) // ex: USART3
// DEBUG_UART baudrate, default: 9600 if not defined
//#define DEBUG_UART_BAUDRATE x
// DEBUG_UART Tx pin name, default: the first one found in PinMap_UART_TX for DEBUG_UART
//#define DEBUG_PINNAME_TX PX_n // PinName used for TX
// Default pin used for 'Serial' instance (ex: ST-Link)
// Mandatory for Firmata
#define PIN_SERIAL_RX PA10
#define PIN_SERIAL_TX PA9
#ifdef __cplusplus
} // extern "C"
#endif
/*----------------------------------------------------------------------------
* Arduino objects - C++ only
*----------------------------------------------------------------------------*/
#ifdef __cplusplus
// These serial port names are intended to allow libraries and architecture-neutral
// sketches to automatically default to the correct port name for a particular type
// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN,
// the first hardware serial port whose RX/TX pins are not dedicated to another use.
//
// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor
//
// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial
//
// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library
//
// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins.
//
// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX
// pins are NOT connected to anything by default.
#define SERIAL_PORT_MONITOR Serial
#define SERIAL_PORT_HARDWARE Serial1
#endif
#endif /* _VARIANT_ARDUINO_STM32_ */