bissen21/Marlin_Firmware
1
0
Fork 0
Code Issues Pull Requests Projects Releases 4 Wiki Activity
27cbb939b2
Marlin_Firmware/Marlin/pins.h

677 lines
19 KiB
C
Raw Normal View History

Further cleanup of comments, partial Doxygen-style Following up on #3231
2016-03-25 01:19:46 -05:00
/**
Added gplv3 header to all Marlin files
2016-03-24 13:01:20 -05:00
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
*/
cleanup
2015-01-25 20:50:09 -06:00
Unify AVR90USB: fastio changes
2017-06-08 18:05:14 -05:00
/**
* Include pins definitions
*
* Pins numbering schemes:
*
* - Digital I/O pin number if used by READ/WRITE macros. (e.g., X_STEP_DIR)
* The FastIO headers map digital pins to their ports and functions.
*
* - Analog Input number if used by analogRead or DAC. (e.g., TEMP_n_PIN)
* These numbers are the same in any pin mapping.
*/
Cleanup stepper current control config options
2017-06-06 04:32:31 -05:00
#ifndef __PINS_H__
#define __PINS_H__
Merged multiple extruder support. Soft PWM. (Sanguinololu can also have PID temperature control) Interrupt save WRITE for addresses > 0x0FF
2011-12-12 12:34:37 -06:00
HAL for Re:ARM (LPC1768) architecture
2017-06-17 16:19:42 -05:00
#define IS_RAMPS_EFB (MB(RAMPS_13_EFB) || MB(RAMPS_14_EFB) || MB(RAMPS_14_RE_ARM_EFB) || MB(RAMPS_SMART_EFB) || MB(RAMPS_DUO_EFB) || MB(RAMPS4DUE_EFB))
#define IS_RAMPS_EEB (MB(RAMPS_13_EEB) || MB(RAMPS_14_EEB) || MB(RAMPS_14_RE_ARM_EEB) || MB(RAMPS_SMART_EEB) || MB(RAMPS_DUO_EEB) || MB(RAMPS4DUE_EEB))
#define IS_RAMPS_EFF (MB(RAMPS_13_EFF) || MB(RAMPS_14_EFF) || MB(RAMPS_14_RE_ARM_EFF) || MB(RAMPS_SMART_EFF) || MB(RAMPS_DUO_EFF) || MB(RAMPS4DUE_EFF))
#define IS_RAMPS_EEF (MB(RAMPS_13_EEF) || MB(RAMPS_14_EEF) || MB(RAMPS_14_RE_ARM_EEF) || MB(RAMPS_SMART_EEF) || MB(RAMPS_DUO_EEF) || MB(RAMPS4DUE_EEF))
#define IS_RAMPS_SF (MB(RAMPS_13_SF) || MB(RAMPS_14_SF) || MB(RAMPS_14_RE_ARM_SF) || MB(RAMPS_SMART_SF) || MB(RAMPS_DUO_SF) || MB(RAMPS4DUE_SF) )
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
//
// RAMPS 1.3 / 1.4 - ATmega1280, ATmega2560
//
#if MB(RAMPS_OLD)
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
#include "pins_RAMPS_OLD.h"
Remove a test from pins_RAMPS_13.h - Add 3 new lines to `pins.h` to remove 2 redundant tests in `pins_RAMPS_13.h`
2015-06-15 01:17:00 -05:00
#elif MB(RAMPS_13_EFB)
Set flags for RAMPS "type" in pins.h
2016-07-30 05:07:20 -05:00
#include "pins_RAMPS_13.h"
#elif MB(RAMPS_13_EEB)
#include "pins_RAMPS_13.h"
#elif MB(RAMPS_13_EFF)
#include "pins_RAMPS_13.h"
#elif MB(RAMPS_13_EEF)
#include "pins_RAMPS_13.h"
#elif MB(RAMPS_13_SF)
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
#include "pins_RAMPS_13.h"
Split RAMPS 1.3 an 1.4 (PR#2741) because of hardware differences on the SERVO0_PIN
2015-10-30 20:05:09 -05:00
#elif MB(RAMPS_14_EFB)
pins_RAMPS_14.h => pins_RAMPS.h
2016-07-30 05:10:30 -05:00
#include "pins_RAMPS.h"
Set flags for RAMPS "type" in pins.h
2016-07-30 05:07:20 -05:00
#elif MB(RAMPS_14_EEB)
pins_RAMPS_14.h => pins_RAMPS.h
2016-07-30 05:10:30 -05:00
#include "pins_RAMPS.h"
Set flags for RAMPS "type" in pins.h
2016-07-30 05:07:20 -05:00
#elif MB(RAMPS_14_EFF)
pins_RAMPS_14.h => pins_RAMPS.h
2016-07-30 05:10:30 -05:00
#include "pins_RAMPS.h"
Set flags for RAMPS "type" in pins.h
2016-07-30 05:07:20 -05:00
#elif MB(RAMPS_14_EEF)
pins_RAMPS_14.h => pins_RAMPS.h
2016-07-30 05:10:30 -05:00
#include "pins_RAMPS.h"
Set flags for RAMPS "type" in pins.h
2016-07-30 05:07:20 -05:00
#elif MB(RAMPS_14_SF)
pins_RAMPS_14.h => pins_RAMPS.h
2016-07-30 05:10:30 -05:00
#include "pins_RAMPS.h"
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
//
// RAMPS Derivatives - ATmega1280, ATmega2560
//
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
#elif MB(3DRAG)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_3DRAG.h" // ATmega1280, ATmega2560
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
#elif MB(K8200)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_K8200.h" // ATmega1280, ATmega2560 (3DRAG)
Add a ported example configuration for the Velleman K8400 (Vertex) printer. Supports both dual and single head printers (with the correct config). Includes community sourced feed rate fix. Rename / move files. Remove redundant definitions.
2016-07-02 08:32:21 -05:00
#elif MB(K8400)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_K8400.h" // ATmega1280, ATmega2560 (3DRAG)
#elif MB(BAM_DICE)
#include "pins_RAMPS.h" // ATmega1280, ATmega2560
#elif MB(BAM_DICE_DUE)
#include "pins_BAM_DICE_DUE.h" // ATmega1280, ATmega2560
#elif MB(MKS_BASE)
#include "pins_MKS_BASE.h" // ATmega1280, ATmega2560
#elif MB(MKS_13)
#include "pins_MKS_13.h" // ATmega1280, ATmega2560
#elif MB(ZRIB_V20)
#include "pins_ZRIB_V20.h" // ATmega1280, ATmega2560 (MKS_13)
#elif MB(FELIX2)
#include "pins_FELIX2.h" // ATmega1280, ATmega2560
#elif MB(RIGIDBOARD)
#include "pins_RIGIDBOARD.h" // ATmega1280, ATmega2560
#elif MB(RIGIDBOARD_V2)
#include "pins_RIGIDBOARD_V2.h" // ATmega1280, ATmega2560
#elif MB(SAINSMART_2IN1)
#include "pins_SAINSMART_2IN1.h" // ATmega1280, ATmega2560
#elif MB(ULTIMAKER)
#include "pins_ULTIMAKER.h" // ATmega1280, ATmega2560
#elif MB(ULTIMAKER_OLD)
#include "pins_ULTIMAKER_OLD.h" // ATmega1280, ATmega2560
#elif MB(AZTEEG_X3)
#include "pins_AZTEEG_X3.h" // ATmega2560
#elif MB(AZTEEG_X3_PRO)
#include "pins_AZTEEG_X3_PRO.h" // ATmega2560
#elif MB(ULTIMAIN_2)
#include "pins_ULTIMAIN_2.h" // ATmega2560
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
#elif MB(RUMBA)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_RUMBA.h" // ATmega2560
#elif MB(BQ_ZUM_MEGA_3D)
#include "pins_BQ_ZUM_MEGA_3D.h" // ATmega2560
//
// Other ATmega1280, ATmega2560
//
#elif MB(CNCONTROLS_11)
#include "pins_CNCONTROLS_11.h" // ATmega1280, ATmega2560
#elif MB(CNCONTROLS_12)
#include "pins_CNCONTROLS_12.h" // ATmega1280, ATmega2560
#elif MB(MIGHTYBOARD_REVE)
#include "pins_MIGHTYBOARD_REVE.h" // ATmega1280, ATmega2560
#elif MB(CHEAPTRONIC)
#include "pins_CHEAPTRONIC.h" // ATmega2560
#elif MB(CHEAPTRONIC_V2)
#include "pins_CHEAPTRONICv2.h" // ATmega2560
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
#elif MB(MEGATRONICS)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_MEGATRONICS.h" // ATmega2560
Add support for Megatronics 3 a la #1426
2015-01-27 17:54:46 -06:00
#elif MB(MEGATRONICS_2)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_MEGATRONICS_2.h" // ATmega2560
Add support for Megatronics 3 a la #1426
2015-01-27 17:54:46 -06:00
#elif MB(MEGATRONICS_3)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_MEGATRONICS_3.h" // ATmega2560
Update pins.h
2016-11-12 05:25:45 -06:00
#elif MB(MEGATRONICS_31)
#define MEGATRONICS_31
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_MEGATRONICS_3.h" // ATmega2560
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
#elif MB(RAMBO)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_RAMBO.h" // ATmega2560
added minirambo pin definitions. V2
2015-06-02 09:04:29 -05:00
#elif MB(MINIRAMBO)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_MINIRAMBO.h" // ATmega2560
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
#elif MB(ELEFU_3)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_ELEFU_3.h" // ATmega2560
Split up pins to make it more manageable Hopefully this is helpful to organization and future expansion….
2015-01-25 20:40:00 -06:00
#elif MB(LEAPFROG)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_LEAPFROG.h" // ATmega1280, ATmega2560
add makerlab mega controller pin configs
2015-07-22 04:35:02 -05:00
#elif MB(MEGACONTROLLER)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_MEGACONTROLLER.h" // ATmega2560
Board A4JP should be SCOOVO_X9H
2017-03-27 22:22:13 -05:00
#elif MB(SCOOVO_X9H)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_SCOOVO_X9H.h" // ATmega2560
Support for Geeetech GT2560 Rev.A/Rev.A+
2017-05-23 15:53:29 -05:00
#elif MB(GT2560_REV_A)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_GT2560_REV_A.h" // ATmega1280, ATmega2560
Support for Geeetech GT2560 Rev.A/Rev.A+
2017-05-23 15:53:29 -05:00
#elif MB(GT2560_REV_A_PLUS)
Organize, document pins.h include lines
2017-08-23 18:24:02 -05:00
#include "pins_GT2560_REV_A_PLUS.h" // ATmega1280, ATmega2560
//
// ATmega1281, ATmega2561
//
#elif MB(MINITRONICS)
#include "pins_MINITRONICS.h" // ATmega1281
//
// Sanguinololu and Derivatives - ATmega644P, ATmega1284P
//
#elif MB(SANGUINOLOLU_11)
#include "pins_SANGUINOLOLU_11.h" // ATmega644P, ATmega1284P
#elif MB(SANGUINOLOLU_12)
#include "pins_SANGUINOLOLU_12.h" // ATmega644P, ATmega1284P
#elif MB(MELZI)
#include "pins_MELZI.h" // ATmega644P, ATmega1284P
#elif MB(MELZI_MAKR3D)
#include "pins_MELZI_MAKR3D.h" // ATmega644P, ATmega1284P
#elif MB(MELZI_CREALITY)
#include "pins_MELZI_CREALITY.h" // ATmega644P, ATmega1284P
#elif MB(STB_11)
#include "pins_STB_11.h" // ATmega644P, ATmega1284P
#elif MB(AZTEEG_X1)
#include "pins_AZTEEG_X1.h" // ATmega644P, ATmega1284P
//
// Other ATmega644P, ATmega644, ATmega1284P
//
#elif MB(GEN3_MONOLITHIC)
#include "pins_GEN3_MONOLITHIC.h" // ATmega644P
#elif MB(GEN3_PLUS)
#include "pins_GEN3_PLUS.h" // ATmega644P, ATmega1284P
#elif MB(GEN6)
#include "pins_GEN6.h" // ATmega644P, ATmega1284P
#elif MB(GEN6_DELUXE)
#include "pins_GEN6_DELUXE.h" // ATmega644P, ATmega1284P
#elif MB(GEN7_CUSTOM)
#include "pins_GEN7_CUSTOM.h" // ATmega644P, ATmega644, ATmega1284P
#elif MB(GEN7_12)
#include "pins_GEN7_12.h" // ATmega644P, ATmega644, ATmega1284P
#elif MB(GEN7_13)
#include "pins_GEN7_13.h" // ATmega644P, ATmega644, ATmega1284P
#elif MB(GEN7_14)
#include "pins_GEN7_14.h" // ATmega644P, ATmega644, ATmega1284P
#elif MB(OMCA_A)
#include "pins_OMCA_A.h" // ATmega644
#elif MB(OMCA)
#include "pins_OMCA.h" // ATmega644P, ATmega644
#elif MB(ANET_10)
#include "pins_ANET_10.h" // ATmega1284P
#elif MB(SETHI)
#include "pins_SETHI.h" // ATmega644P, ATmega644, ATmega1284P
//
// Teensyduino - AT90USB1286, AT90USB1286P
//
#elif MB(TEENSYLU)
#include "pins_TEENSYLU.h" // AT90USB1286, AT90USB1286P
#elif MB(PRINTRBOARD)
#include "pins_PRINTRBOARD.h" // AT90USB1286
#elif MB(PRINTRBOARD_REVF)
#include "pins_PRINTRBOARD_REVF.h" // AT90USB1286
#elif MB(BRAINWAVE)
#include "pins_BRAINWAVE.h" // AT90USB646
#elif MB(BRAINWAVE_PRO)
#include "pins_BRAINWAVE_PRO.h" // AT90USB1286
#elif MB(SAV_MKI)
#include "pins_SAV_MKI.h" // AT90USB1286
#elif MB(TEENSY2)
#include "pins_TEENSY2.h" // AT90USB1286
#elif MB(5DPRINT)
#include "pins_5DPRINT.h" // AT90USB1286
Implement HAL and apply macros across code-base Implement AVR Platform
2017-06-17 18:36:10 -05:00
//
HAL for Re:ARM (LPC1768) architecture
2017-06-17 16:19:42 -05:00
// Re-ARM - LPC1768
//
#elif MB(RAMPS_14_RE_ARM_EFB)
#include "pins_RAMPS_RE_ARM.h"
#elif MB(RAMPS_14_RE_ARM_EEB)
#include "pins_RAMPS_RE_ARM.h"
#elif MB(RAMPS_14_RE_ARM_EFF)
#include "pins_RAMPS_RE_ARM.h"
#elif MB(RAMPS_14_RE_ARM_EEF)
#include "pins_RAMPS_RE_ARM.h"
#elif MB(RAMPS_14_RE_ARM_SF)
#include "pins_RAMPS_RE_ARM.h"
//
// Other 32-bit Boards
Implement HAL and apply macros across code-base Implement AVR Platform
2017-06-17 18:36:10 -05:00
//
#elif MB(TEENSY35_36)
#include "pins_TEENSY35_36.h"
#elif MB(DUE3DOM)
#include "pins_DUE3DOM.h"
#elif MB(DUE3DOM_MINI)
#include "pins_DUE3DOM_MINI.h"
#elif MB(RADDS)
#include "pins_RADDS.h"
#elif MB(RAMPS_FD_V1)
#include "pins_RAMPS_FD.h"
#elif MB(RAMPS_FD_V2)
#include "pins_RAMPS_FD_V2.h"
#elif MB(RAMPS_SMART_EFB)
#include "pins_RAMPS_SMART.h"
#elif MB(RAMPS_SMART_EEB)
#include "pins_RAMPS_SMART.h"
#elif MB(RAMPS_SMART_EFF)
#include "pins_RAMPS_SMART.h"
#elif MB(RAMPS_SMART_EEF)
#include "pins_RAMPS_SMART.h"
#elif MB(RAMPS_SMART_SF)
#include "pins_RAMPS_SMART.h"
#elif MB(RAMPS_DUO_EFB)
#include "pins_RAMPS_DUO.h"
#elif MB(RAMPS_DUO_EEB)
#include "pins_RAMPS_DUO.h"
#elif MB(RAMPS_DUO_EFF)
#include "pins_RAMPS_DUO.h"
#elif MB(RAMPS_DUO_EEF)
#include "pins_RAMPS_DUO.h"
#elif MB(RAMPS_DUO_SF)
#include "pins_RAMPS_DUO.h"
#elif MB(RAMPS4DUE_EFB)
#include "pins_RAMPS4DUE.h"
#elif MB(RAMPS4DUE_EEB)
#include "pins_RAMPS4DUE.h"
#elif MB(RAMPS4DUE_EFF)
#include "pins_RAMPS4DUE.h"
#elif MB(RAMPS4DUE_EEF)
#include "pins_RAMPS4DUE.h"
#elif MB(RAMPS4DUE_SF)
#include "pins_RAMPS4DUE.h"
#elif MB(ALLIGATOR)
#include "pins_ALLIGATOR_R2.h"
#elif MB(RAMPS_FD_V1) || MB(RAMPS_FD_V2)
#include "pins_RAMPS_FD_v1.h"
Merged multiple extruder support. Soft PWM. (Sanguinololu can also have PID temperature control) Interrupt save WRITE for addresses > 0x0FF
2011-12-12 12:34:37 -06:00
#else
Enclose all #error strings with apostrophes
2016-05-13 07:10:23 -05:00
#error "Unknown MOTHERBOARD value set in Configuration.h"
Merged multiple extruder support. Soft PWM. (Sanguinololu can also have PID temperature control) Interrupt save WRITE for addresses > 0x0FF
2011-12-12 12:34:37 -06:00
#endif
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
// Define certain undefined pins
#ifndef X_MS1_PIN
#define X_MS1_PIN -1
#endif
#ifndef X_MS2_PIN
#define X_MS2_PIN -1
#endif
#ifndef Y_MS1_PIN
#define Y_MS1_PIN -1
#endif
#ifndef Y_MS2_PIN
#define Y_MS2_PIN -1
#endif
#ifndef Z_MS1_PIN
#define Z_MS1_PIN -1
#endif
#ifndef Z_MS2_PIN
#define Z_MS2_PIN -1
#endif
#ifndef E0_MS1_PIN
#define E0_MS1_PIN -1
#endif
#ifndef E0_MS2_PIN
#define E0_MS2_PIN -1
#endif
#ifndef E1_MS1_PIN
#define E1_MS1_PIN -1
#endif
#ifndef E1_MS2_PIN
#define E1_MS2_PIN -1
#endif
#ifndef FAN_PIN
#define FAN_PIN -1
#endif
#ifndef FAN1_PIN
#define FAN1_PIN -1
#endif
#ifndef FAN2_PIN
#define FAN2_PIN -1
#endif
Implement USE_CONTROLLER_FAN as a feature
2017-05-02 20:18:31 -05:00
#ifndef CONTROLLER_FAN_PIN
#define CONTROLLER_FAN_PIN -1
Allow override of CONTROLLERFAN_PIN with RAMPS EFF
2016-08-06 19:16:16 -05:00
#endif
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
New feature: Part-Cooling Fan Multiplexer
2017-08-15 07:48:10 -05:00
#ifndef FANMUX0_PIN
#define FANMUX0_PIN -1
#endif
#ifndef FANMUX1_PIN
#define FANMUX1_PIN -1
#endif
#ifndef FANMUX2_PIN
#define FANMUX2_PIN -1
#endif
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
#ifndef HEATER_0_PIN
#define HEATER_0_PIN -1
#endif
#ifndef HEATER_1_PIN
#define HEATER_1_PIN -1
#endif
#ifndef HEATER_2_PIN
#define HEATER_2_PIN -1
#endif
#ifndef HEATER_3_PIN
#define HEATER_3_PIN -1
#endif
More support for 4th extruder or heater
2016-10-05 01:49:59 -05:00
#ifndef HEATER_4_PIN
#define HEATER_4_PIN -1
#endif
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
#ifndef HEATER_BED_PIN
#define HEATER_BED_PIN -1
#endif
#ifndef TEMP_0_PIN
#define TEMP_0_PIN -1
#endif
#ifndef TEMP_1_PIN
#define TEMP_1_PIN -1
#endif
#ifndef TEMP_2_PIN
#define TEMP_2_PIN -1
#endif
#ifndef TEMP_3_PIN
#define TEMP_3_PIN -1
#endif
Header and pins changes to support 5 extruders
2017-04-06 16:46:30 -05:00
#ifndef TEMP_4_PIN
#define TEMP_4_PIN -1
#endif
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
#ifndef TEMP_BED_PIN
#define TEMP_BED_PIN -1
#endif
#ifndef SD_DETECT_PIN
#define SD_DETECT_PIN -1
#endif
#ifndef SDPOWER
#define SDPOWER -1
#endif
#ifndef SDSS
#define SDSS -1
#endif
#ifndef LED_PIN
#define LED_PIN -1
#endif
#ifndef PS_ON_PIN
#define PS_ON_PIN -1
#endif
#ifndef KILL_PIN
#define KILL_PIN -1
#endif
#ifndef SUICIDE_PIN
#define SUICIDE_PIN -1
#endif
Move MAX_EXTRUDERS to pins.h
2016-10-22 10:07:51 -05:00
#ifndef MAX_EXTRUDERS
Header and pins changes to support 5 extruders
2017-04-06 16:46:30 -05:00
#define MAX_EXTRUDERS 5
Move MAX_EXTRUDERS to pins.h
2016-10-22 10:07:51 -05:00
#endif
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
// Marlin needs to account for pins that equal -1
Should marlinAnalogInputToDigitalPin use analogInputToDigitalPin?
2016-10-05 02:01:52 -05:00
#define marlinAnalogInputToDigitalPin(p) ((p) == -1 ? -1 : analogInputToDigitalPin(p))
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
Predefine auto fan pins in some pins files
2016-10-22 18:25:59 -05:00
//
// Assign auto fan pins if needed
//
#if !defined(E0_AUTO_FAN_PIN) && defined(ORIG_E0_AUTO_FAN_PIN)
#define E0_AUTO_FAN_PIN ORIG_E0_AUTO_FAN_PIN
#endif
#if !defined(E1_AUTO_FAN_PIN) && defined(ORIG_E1_AUTO_FAN_PIN)
#define E1_AUTO_FAN_PIN ORIG_E1_AUTO_FAN_PIN
#endif
#if !defined(E2_AUTO_FAN_PIN) && defined(ORIG_E2_AUTO_FAN_PIN)
#define E2_AUTO_FAN_PIN ORIG_E2_AUTO_FAN_PIN
#endif
#if !defined(E3_AUTO_FAN_PIN) && defined(ORIG_E3_AUTO_FAN_PIN)
#define E3_AUTO_FAN_PIN ORIG_E3_AUTO_FAN_PIN
#endif
Support 5 extruder auto fans
2017-04-08 02:42:07 -05:00
#if !defined(E4_AUTO_FAN_PIN) && defined(ORIG_E4_AUTO_FAN_PIN)
#define E4_AUTO_FAN_PIN ORIG_E4_AUTO_FAN_PIN
#endif
Predefine auto fan pins in some pins files
2016-10-22 18:25:59 -05:00
Add support for 4th extruder #1405 includes some changes to pins.h for a 4th extruder. This commit applies those changes. It also deals with a possible problem with SENSITIVE_PINS.
2015-01-25 21:43:43 -06:00
// List of pins which to ignore when asked to change by gcode, 0 and 1 are RX and TX, do not mess with those!
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-05-26 19:43:20 -05:00
#define _E0_PINS E0_STEP_PIN, E0_DIR_PIN, E0_ENABLE_PIN, E0_MS1_PIN, E0_MS2_PIN,
Make sure _Ex_PINS is defined Also fix analogInputToDigitalPin so it uses proper C hex notation
2015-01-27 17:19:03 -06:00
#define _E1_PINS
#define _E2_PINS
#define _E3_PINS
More support for 4th extruder or heater
2016-10-05 01:49:59 -05:00
#define _E4_PINS
Make sure _Ex_PINS is defined Also fix analogInputToDigitalPin so it uses proper C hex notation
2015-01-27 17:19:03 -06:00
Support for two switching extruders
2017-06-19 16:54:37 -05:00
#if ENABLED(SWITCHING_EXTRUDER)
// Tools 0 and 1 use E0
#if EXTRUDERS > 2 // Tools 2 and 3 use E1
#undef _E1_PINS
#define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, E1_MS1_PIN, E1_MS2_PIN,
#if EXTRUDERS > 4 // Tools 4 and 5 use E2
#undef _E2_PINS
#define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN,
#endif
#endif
#elif EXTRUDERS > 1
Fix compiler warnings - Patched up for most included configurations
2015-03-27 22:29:05 -05:00
#undef _E1_PINS
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-05-26 19:43:20 -05:00
#define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN, E1_MS1_PIN, E1_MS2_PIN,
tweak
2015-01-26 07:17:08 -06:00
#if EXTRUDERS > 2
Fix compiler warnings - Patched up for most included configurations
2015-03-27 22:29:05 -05:00
#undef _E2_PINS
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-05-26 19:43:20 -05:00
#define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN,
tweak
2015-01-26 07:17:08 -06:00
#if EXTRUDERS > 3
Fix compiler warnings - Patched up for most included configurations
2015-03-27 22:29:05 -05:00
#undef _E3_PINS
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-05-26 19:43:20 -05:00
#define _E3_PINS E3_STEP_PIN, E3_DIR_PIN, E3_ENABLE_PIN,
More support for 4th extruder or heater
2016-10-05 01:49:59 -05:00
#if EXTRUDERS > 4
#undef _E4_PINS
#define _E4_PINS E4_STEP_PIN, E4_DIR_PIN, E4_ENABLE_PIN,
Header and pins changes to support 5 extruders
2017-04-06 16:46:30 -05:00
#endif // EXTRUDERS > 4
#endif // EXTRUDERS > 3
#endif // EXTRUDERS > 2
#endif // EXTRUDERS > 1
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-05-26 19:43:20 -05:00
Rename auto fan pins and add auto fan flags
2016-10-22 18:25:42 -05:00
#define _H0_PINS HEATER_0_PIN, E0_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_0_PIN),
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-05-26 19:43:20 -05:00
#define _H1_PINS
#define _H2_PINS
#define _H3_PINS
More support for 4th extruder or heater
2016-10-05 01:49:59 -05:00
#define _H4_PINS
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-05-26 19:43:20 -05:00
#if HOTENDS > 1
#undef _H1_PINS
Rename auto fan pins and add auto fan flags
2016-10-22 18:25:42 -05:00
#define _H1_PINS HEATER_1_PIN, E1_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_1_PIN),
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-05-26 19:43:20 -05:00
#if HOTENDS > 2
#undef _H2_PINS
Rename auto fan pins and add auto fan flags
2016-10-22 18:25:42 -05:00
#define _H2_PINS HEATER_2_PIN, E2_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_2_PIN),
SINGLENOZZLE: EXTRUDERS versus HOTENDS
2016-05-26 19:43:20 -05:00
#if HOTENDS > 3
#undef _H3_PINS
Rename auto fan pins and add auto fan flags
2016-10-22 18:25:42 -05:00
#define _H3_PINS HEATER_3_PIN, E3_AUTO_FAN_PIN, marlinAnalogInputToDigitalPin(TEMP_3_PIN),
More support for 4th extruder or heater
2016-10-05 01:49:59 -05:00
#if HOTENDS > 4
#undef _H4_PINS
#define _H4_PINS HEATER_4_PIN, marlinAnalogInputToDigitalPin(TEMP_4_PIN),
Header and pins changes to support 5 extruders
2017-04-06 16:46:30 -05:00
#endif // HOTENDS > 4
#endif // HOTENDS > 3
#endif // HOTENDS > 2
Implement MIXING_EXTRUDER and SWITCHING_EXTRUDER
2016-06-28 17:06:56 -05:00
#elif ENABLED(MIXING_EXTRUDER)
#undef _E1_PINS
#define _E1_PINS E1_STEP_PIN, E1_DIR_PIN, E1_ENABLE_PIN,
#if MIXING_STEPPERS > 2
#undef _E2_PINS
#define _E2_PINS E2_STEP_PIN, E2_DIR_PIN, E2_ENABLE_PIN,
#if MIXING_STEPPERS > 3
#undef _E3_PINS
#define _E3_PINS E3_STEP_PIN, E3_DIR_PIN, E3_ENABLE_PIN,
More support for 4th extruder or heater
2016-10-05 01:49:59 -05:00
#if MIXING_STEPPERS > 4
#undef _E4_PINS
#define _E4_PINS E4_STEP_PIN, E4_DIR_PIN, E4_ENABLE_PIN,
Header and pins changes to support 5 extruders
2017-04-06 16:46:30 -05:00
#endif // MIXING_STEPPERS > 4
#endif // MIXING_STEPPERS > 3
#endif // MIXING_STEPPERS > 2
#endif // MIXING_STEPPERS > 1
Only protect the heater pins for the defined extruders. Changed the way the extruder pins are defined so it doesn't create extra -1 entries in the list.
2012-02-29 08:49:02 -06:00
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
#define BED_PINS HEATER_BED_PIN, marlinAnalogInputToDigitalPin(TEMP_BED_PIN),
//
// Assign endstop pins for boards with only 3 connectors
//
For boards with only one endstop per axis, automatically set *_MIN_PIN and *_MAX_PIN according to *_HOME_DIR.
2012-12-16 14:08:55 -06:00
#ifdef X_STOP_PIN
#if X_HOME_DIR < 0
#define X_MIN_PIN X_STOP_PIN
#define X_MAX_PIN -1
#else
#define X_MIN_PIN -1
#define X_MAX_PIN X_STOP_PIN
#endif
#endif
#ifdef Y_STOP_PIN
#if Y_HOME_DIR < 0
#define Y_MIN_PIN Y_STOP_PIN
#define Y_MAX_PIN -1
#else
#define Y_MIN_PIN -1
#define Y_MAX_PIN Y_STOP_PIN
#endif
#endif
#ifdef Z_STOP_PIN
#if Z_HOME_DIR < 0
#define Z_MIN_PIN Z_STOP_PIN
#define Z_MAX_PIN -1
#else
#define Z_MIN_PIN -1
#define Z_MAX_PIN Z_STOP_PIN
#endif
#endif
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
//
// Disable unused endstop / probe pins
//
Clean up probe config options
2016-09-18 23:28:11 -05:00
#if DISABLED(Z_MIN_PROBE_ENDSTOP)
Make Z_PROBE a Z_MIN_PROBE (PR#65) Currently we use the probe exclusively as a device to find the build platform(bed). For the currently supported setups this means, we use it as a additional min-endstop. A triggered when not deployed probe disturbs the homing process for max-endstops. Rename ENDSTOPPULLUP_ZPROBE to ENDSTOPPULLUP_ZMIN_PROBE Rename Z_PROBE_ENDSTOP_INVERTING to Z_MIN_PROBE_ENDSTOP_INVERTING Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP Rename DISABLE_Z_PROBE_ENDSTOP to DISABLE_Z_MIN_PROBE_ENDSTOP Rename Z_PROBE_REPEATABILITY_TEST to Z_MIN_PROBE_REPEATABILITY_TEST Rename Z_PROBE_ENDSTOP to Z_MIN_PROBE_ENDSTOP Adjust comments accordingly Remove Z_MAX check for the probe in update_endstops(). Using an delta related idea of @clefranc from #61, extended to the general change for all setups. Tested with Prusa i3, max-z-endstop and permanently triggered z-probe. Worked for @clefranc's delta.
2015-08-10 03:35:39 -05:00
#undef Z_MIN_PROBE_PIN
#define Z_MIN_PROBE_PIN -1
Enabled separate Z Probe and Z Axis endstop use at same time. Typo fixes in comments in existing code.
2015-03-28 04:31:51 -05:00
#endif
Drop DISABLE_M(IN|AX)_ENDSTOPS, replace with individual endstop flags
2016-03-02 04:00:34 -06:00
#if DISABLED(USE_XMAX_PLUG)
New Feature: Z_DUAL_ENDSTOPS Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. That way the machine is capable to align the bed during home, since both Z steppers are homed. There is also an implementation of M666 (software endstops adjustment) to this feature. After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive. Play a little bit with small adjustments (0.5mm) and check the behaviour. The M119 (endstops report) will start reporting the Z2 Endstop as well.
2015-03-24 12:06:44 -05:00
#undef X_MAX_PIN
#define X_MAX_PIN -1
#endif
Drop DISABLE_M(IN|AX)_ENDSTOPS, replace with individual endstop flags
2016-03-02 04:00:34 -06:00
#if DISABLED(USE_YMAX_PLUG)
Fix lost undef Y_MAX_PIN in pins.h
2016-03-23 06:48:06 -05:00
#undef Y_MAX_PIN
New Feature: Z_DUAL_ENDSTOPS Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. That way the machine is capable to align the bed during home, since both Z steppers are homed. There is also an implementation of M666 (software endstops adjustment) to this feature. After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive. Play a little bit with small adjustments (0.5mm) and check the behaviour. The M119 (endstops report) will start reporting the Z2 Endstop as well.
2015-03-24 12:06:44 -05:00
#define Y_MAX_PIN -1
#endif
Drop DISABLE_M(IN|AX)_ENDSTOPS, replace with individual endstop flags
2016-03-02 04:00:34 -06:00
#if DISABLED(USE_ZMAX_PLUG)
New Feature: Z_DUAL_ENDSTOPS Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. That way the machine is capable to align the bed during home, since both Z steppers are homed. There is also an implementation of M666 (software endstops adjustment) to this feature. After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive. Play a little bit with small adjustments (0.5mm) and check the behaviour. The M119 (endstops report) will start reporting the Z2 Endstop as well.
2015-03-24 12:06:44 -05:00
#undef Z_MAX_PIN
#define Z_MAX_PIN -1
#endif
Drop DISABLE_M(IN|AX)_ENDSTOPS, replace with individual endstop flags
2016-03-02 04:00:34 -06:00
#if DISABLED(USE_XMIN_PLUG)
#undef X_MIN_PIN
#define X_MIN_PIN -1
#endif
#if DISABLED(USE_YMIN_PLUG)
#undef Y_MIN_PIN
#define Y_MIN_PIN -1
#endif
#if DISABLED(USE_ZMIN_PLUG)
Styling adjustments (PR#2668 & PR#2670) Keep "astyled" reformatting
2015-10-03 01:08:58 -05:00
#undef Z_MIN_PIN
New Feature: Z_DUAL_ENDSTOPS Z_DUAL_ENDSTOPS is a feature to enable the use of 2 endstops for both Z steppers - Let's call them Z stepper and Z2 stepper. That way the machine is capable to align the bed during home, since both Z steppers are homed. There is also an implementation of M666 (software endstops adjustment) to this feature. After Z homing, this adjustment is applied to just one of the steppers in order to align the bed. One just need to home the Z axis and measure the distance difference between both Z axis and apply the math: Z adjust = Z - Z2. If the Z stepper axis is closer to the bed, the measure Z > Z2 (yes, it is.. think about it) and the Z adjust would be positive. Play a little bit with small adjustments (0.5mm) and check the behaviour. The M119 (endstops report) will start reporting the Z2 Endstop as well.
2015-03-24 12:06:44 -05:00
#define Z_MIN_PIN -1
#endif
Assign -1 to LCD_PINS_D4-7 if not defined
2017-07-06 22:47:37 -05:00
#ifndef LCD_PINS_D4
#define LCD_PINS_D4 -1
#endif
#ifndef LCD_PINS_D5
#define LCD_PINS_D5 -1
#endif
#ifndef LCD_PINS_D6
#define LCD_PINS_D6 -1
#endif
#ifndef LCD_PINS_D7
#define LCD_PINS_D7 -1
#endif
For Dual Y/Z use the next available extruder pins
2016-02-09 22:04:07 -06:00
//
Automatically set X2 stepper pins
2016-05-17 16:56:49 -05:00
// Dual X-carriage, Dual Y, Dual Z support
For Dual Y/Z use the next available extruder pins
2016-02-09 22:04:07 -06:00
//
Automatically set X2 stepper pins
2016-05-17 16:56:49 -05:00
#define _X2_PINS
#define _Y2_PINS
#define _Z2_PINS
For Dual Y/Z use the next available extruder pins
2016-02-09 22:04:07 -06:00
#define __EPIN(p,q) E##p##_##q##_PIN
#define _EPIN(p,q) __EPIN(p,q)
X_DUAL_STEPPER_DRIVERS implementation
2016-07-11 12:19:07 -05:00
// The X2 axis, if any, should be the next open extruder port
#if ENABLED(DUAL_X_CARRIAGE) || ENABLED(X_DUAL_STEPPER_DRIVERS)
Automatically set X2 stepper pins
2016-05-17 16:56:49 -05:00
#ifndef X2_STEP_PIN
Implement MIXING_EXTRUDER and SWITCHING_EXTRUDER
2016-06-28 17:06:56 -05:00
#define X2_STEP_PIN _EPIN(E_STEPPERS, STEP)
#define X2_DIR_PIN _EPIN(E_STEPPERS, DIR)
#define X2_ENABLE_PIN _EPIN(E_STEPPERS, ENABLE)
Throw an error if no E stepper is free for X2, Y2, Z2
2017-05-02 15:08:16 -05:00
#if X2_ENABLE_PIN == 0
#error "No E stepper plug left for X2!"
#endif
Automatically set X2 stepper pins
2016-05-17 16:56:49 -05:00
#endif
#undef _X2_PINS
#define _X2_PINS X2_STEP_PIN, X2_DIR_PIN, X2_ENABLE_PIN,
Implement MIXING_EXTRUDER and SWITCHING_EXTRUDER
2016-06-28 17:06:56 -05:00
#define Y2_E_INDEX INCREMENT(E_STEPPERS)
Automatically set X2 stepper pins
2016-05-17 16:56:49 -05:00
#else
Implement MIXING_EXTRUDER and SWITCHING_EXTRUDER
2016-06-28 17:06:56 -05:00
#define Y2_E_INDEX E_STEPPERS
Automatically set X2 stepper pins
2016-05-17 16:56:49 -05:00
#endif
For Dual Y/Z use the next available extruder pins
2016-02-09 22:04:07 -06:00
// The Y2 axis, if any, should be the next open extruder port
X_DUAL_STEPPER_DRIVERS implementation
2016-07-11 12:19:07 -05:00
#if ENABLED(Y_DUAL_STEPPER_DRIVERS)
#ifndef Y2_STEP_PIN
#define Y2_STEP_PIN _EPIN(Y2_E_INDEX, STEP)
#define Y2_DIR_PIN _EPIN(Y2_E_INDEX, DIR)
#define Y2_ENABLE_PIN _EPIN(Y2_E_INDEX, ENABLE)
Throw an error if no E stepper is free for X2, Y2, Z2
2017-05-02 15:08:16 -05:00
#if Y2_ENABLE_PIN == 0
#error "No E stepper plug left for Y2!"
#endif
X_DUAL_STEPPER_DRIVERS implementation
2016-07-11 12:19:07 -05:00
#endif
Automatically set X2 stepper pins
2016-05-17 16:56:49 -05:00
#undef _Y2_PINS
#define _Y2_PINS Y2_STEP_PIN, Y2_DIR_PIN, Y2_ENABLE_PIN,
X_DUAL_STEPPER_DRIVERS implementation
2016-07-11 12:19:07 -05:00
#define Z2_E_INDEX INCREMENT(Y2_E_INDEX)
#else
#define Z2_E_INDEX Y2_E_INDEX
Move Y2 and Z2 pins defines to pins.h
2015-08-27 20:08:09 -05:00
#endif
For Dual Y/Z use the next available extruder pins
2016-02-09 22:04:07 -06:00
// The Z2 axis, if any, should be the next open extruder port
X_DUAL_STEPPER_DRIVERS implementation
2016-07-11 12:19:07 -05:00
#if ENABLED(Z_DUAL_STEPPER_DRIVERS)
#ifndef Z2_STEP_PIN
#define Z2_STEP_PIN _EPIN(Z2_E_INDEX, STEP)
#define Z2_DIR_PIN _EPIN(Z2_E_INDEX, DIR)
#define Z2_ENABLE_PIN _EPIN(Z2_E_INDEX, ENABLE)
Throw an error if no E stepper is free for X2, Y2, Z2
2017-05-02 15:08:16 -05:00
#if Z2_ENABLE_PIN == 0
#error "No E stepper plug left for Z2!"
#endif
X_DUAL_STEPPER_DRIVERS implementation
2016-07-11 12:19:07 -05:00
#endif
Automatically set X2 stepper pins
2016-05-17 16:56:49 -05:00
#undef _Z2_PINS
#define _Z2_PINS Z2_STEP_PIN, Z2_DIR_PIN, Z2_ENABLE_PIN,
Move Y2 and Z2 pins defines to pins.h
2015-08-27 20:08:09 -05:00
#endif
Fix missing backslash in macro
2015-04-04 05:35:16 -05:00
#define SENSITIVE_PINS { 0, 1, \
Styling adjustments (PR#2668 & PR#2670) Keep "astyled" reformatting
2015-10-03 01:08:58 -05:00
X_STEP_PIN, X_DIR_PIN, X_ENABLE_PIN, X_MIN_PIN, X_MAX_PIN, \
Y_STEP_PIN, Y_DIR_PIN, Y_ENABLE_PIN, Y_MIN_PIN, Y_MAX_PIN, \
Z_STEP_PIN, Z_DIR_PIN, Z_ENABLE_PIN, Z_MIN_PIN, Z_MAX_PIN, Z_MIN_PROBE_PIN, \
Implement USE_CONTROLLER_FAN as a feature
2017-05-02 20:18:31 -05:00
PS_ON_PIN, HEATER_BED_PIN, FAN_PIN, FAN1_PIN, FAN2_PIN, CONTROLLER_FAN_PIN, \
More support for 4th extruder or heater
2016-10-05 01:49:59 -05:00
_E0_PINS _E1_PINS _E2_PINS _E3_PINS _E4_PINS BED_PINS \
_H0_PINS _H1_PINS _H2_PINS _H3_PINS _H4_PINS \
Automatically set X2 stepper pins
2016-05-17 16:56:49 -05:00
_X2_PINS _Y2_PINS _Z2_PINS \
Cleanup pins files, fixup analogtodigitalpin, etc.
2016-05-07 20:41:20 -05:00
X_MS1_PIN, X_MS2_PIN, Y_MS1_PIN, Y_MS2_PIN, Z_MS1_PIN, Z_MS2_PIN \
Styling adjustments (PR#2668 & PR#2670) Keep "astyled" reformatting
2015-10-03 01:08:58 -05:00
}
Add support for 4th extruder #1405 includes some changes to pins.h for a 4th extruder. This commit applies those changes. It also deals with a possible problem with SENSITIVE_PINS.
2015-01-25 21:43:43 -06:00
Switch SD2cadrLib to fastio Replace all fastDigitalRead/Write() with READ/WRITE() Define SCK_PIN, MISO_PIN, MOSI_PIN in pins.h if not already defined in the pins_*.h files. Remove these conditional pin definitions from the pin-files. They are now always defined. Define separate sets of SPI-pins for AT90USB with and without Teensy support in fastio.h. Likely this was the main reason for all that confusion about the AT90USB-SPI pins.
2016-07-27 05:40:44 -05:00
#define HAS_DIGIPOTSS (PIN_EXISTS(DIGIPOTSS))
Implement HAL and apply macros across code-base Implement AVR Platform
2017-06-17 18:36:10 -05:00
// Note: default SPI pins are defined in the HAL
#include "src/HAL/HAL_spi_pins.h"
Switch SD2cadrLib to fastio Replace all fastDigitalRead/Write() with READ/WRITE() Define SCK_PIN, MISO_PIN, MOSI_PIN in pins.h if not already defined in the pins_*.h files. Remove these conditional pin definitions from the pin-files. They are now always defined. Define separate sets of SPI-pins for AT90USB with and without Teensy support in fastio.h. Likely this was the main reason for all that confusion about the AT90USB-SPI pins.
2016-07-27 05:40:44 -05:00
Cleanup stepper current control config options
2017-06-06 04:32:31 -05:00
#endif // __PINS_H__
Reference in New Issue Copy Permalink