Marlin_Firmware/Marlin/src/pins/pins_AZTEEG_X5_MINI_WIFI.h

209 lines
6.7 KiB
C
Raw Normal View History

2018-08-21 23:58:26 -05:00
/**
* Marlin 3D Printer Firmware
2019-02-12 15:06:53 -06:00
* Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
2018-08-21 23:58:26 -05:00
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Azteeg X5 MINI pin assignments
*/
#ifndef TARGET_LPC1768
#error "Oops! Make sure you have the LPC1768 environment selected in your IDE."
2018-08-21 23:58:26 -05:00
#endif
#define BOARD_NAME "Azteeg X5 MINI WIFI"
#define BOARD_WEBSITE_URL "http://www.panucatt.com/azteeg_X5_mini_reprap_3d_printer_controller_p/ax5mini.htm"
2018-08-21 23:58:26 -05:00
//
// LED
2018-08-21 23:58:26 -05:00
//
#define LED_PIN P1_18
2018-08-21 23:58:26 -05:00
//
// Servo
//
#define SERVO0_PIN P1_29
2018-08-21 23:58:26 -05:00
//
// Limit Switches
//
#define X_MIN_PIN P1_24
#define Y_MIN_PIN P1_26
#define Z_MIN_PIN P1_28
//
// Steppers
//
#define X_STEP_PIN P2_01
#define X_DIR_PIN P0_11
#define X_ENABLE_PIN P0_10
#define Y_STEP_PIN P2_02
#define Y_DIR_PIN P0_20
#define Y_ENABLE_PIN P0_19
#define Z_STEP_PIN P2_03
#define Z_DIR_PIN P0_22
#define Z_ENABLE_PIN P0_21
#define E0_STEP_PIN P2_00
#define E0_DIR_PIN P0_05
#define E0_ENABLE_PIN P0_04
//
// DIGIPOT slave addresses
//
#define DIGIPOT_I2C_ADDRESS_A 0x58 // shifted slave address for first DIGIPOT (0x58 <- 0x2C << 1)
#define DIGIPOT_I2C_ADDRESS_B 0x5C // shifted slave address for second DIGIPOT (0x5C <- 0x2E << 1)
//
// Temperature Sensors
// 3.3V max when defined as an analog input
//
#define TEMP_BED_PIN 0 // A0 (TH1)
#define TEMP_0_PIN 1 // A1 (TH2)
//
// Heaters / Fans
//
#define HEATER_BED_PIN P2_07
#define HEATER_0_PIN P2_05
#ifndef FAN_PIN
#define FAN_PIN P0_26
#endif
#define FAN1_PIN P1_25
//
// Display
//
#if ENABLED(ULTRA_LCD)
#if ENABLED(CR10_STOCKDISPLAY)
// Re-Arm can support Creality stock display without SD card reader and single cable on EXP3.
// Re-Arm J3 pins 1 (p1.31) & 2 (P3.26) are not used. Stock cable will need to have one
// 10-pin IDC connector trimmed or replaced with a 12-pin IDC connector to fit J3.
// Requires REVERSE_ENCODER_DIRECTION in Configuration.h
#define BEEPER_PIN P2_11 // J3-3 & AUX-4
#define BTN_EN1 P0_16 // J3-7 & AUX-4
#define BTN_EN2 P1_23 // J3-5 & AUX-4
#define BTN_ENC P3_25 // J3-4 & AUX-4
#define LCD_PINS_RS P0_15 // J3-9 & AUX-4 (CS)
#define LCD_PINS_ENABLE P0_18 // J3-10 & AUX-3 (SID, MOSI)
#define LCD_PINS_D4 P2_06 // J3-8 & AUX-3 (SCK, CLK)
#else
#define BTN_EN1 P3_26 // (31) J3-2 & AUX-4
#define BTN_EN2 P3_25 // (33) J3-4 & AUX-4
#define BTN_ENC P2_11 // (35) J3-3 & AUX-4
#define SD_DETECT_PIN P1_31 // (49) not 5V tolerant J3-1 & AUX-3
#define KILL_PIN P1_22 // (41) J5-4 & AUX-4
#define LCD_PINS_RS P0_16 // (16) J3-7 & AUX-4
#define LCD_SDSS P0_16 // (16) J3-7 & AUX-4
#define LCD_BACKLIGHT_PIN P0_16 // (16) J3-7 & AUX-4 - only used on DOGLCD controllers
#define LCD_PINS_ENABLE P0_18 // (51) (MOSI) J3-10 & AUX-3
#define LCD_PINS_D4 P0_15 // (52) (SCK) J3-9 & AUX-3
#define DOGLCD_A0 P2_06 // (59) J3-8 & AUX-2
#if ENABLED(REPRAPWORLD_KEYPAD)
#define SHIFT_OUT P0_18 // (51) (MOSI) J3-10 & AUX-3
#define SHIFT_CLK P0_15 // (52) (SCK) J3-9 & AUX-3
#define SHIFT_LD P1_31 // (49) not 5V tolerant J3-1 & AUX-3
#elif DISABLED(NEWPANEL)
//#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4
//#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4
//#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4
//#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4
#endif
#if ENABLED(VIKI2) || ENABLED(miniVIKI)
//#define LCD_SCREEN_ROT_180
#define BEEPER_PIN P1_30 // (37) may change if cable changes
#define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2
#define DOGLCD_SCK SCK_PIN
#define DOGLCD_MOSI MOSI_PIN
#define STAT_LED_BLUE_PIN P0_26 // (63) may change if cable changes
#define STAT_LED_RED_PIN P1_21 // ( 6) may change if cable changes
#else
#if ENABLED(ULTIPANEL)
#define LCD_PINS_D5 P1_17 // (71) ENET_MDIO
#define LCD_PINS_D6 P1_14 // (73) ENET_RX_ER
#define LCD_PINS_D7 P1_10 // (75) ENET_RXD1
#endif
#define BEEPER_PIN P1_30 // (37) not 5V tolerant
#define DOGLCD_CS P0_16 // (16)
#endif
#if ENABLED(MINIPANEL)
// GLCD features
//#define LCD_CONTRAST 190
// Uncomment screen orientation
//#define LCD_SCREEN_ROT_90
//#define LCD_SCREEN_ROT_180
//#define LCD_SCREEN_ROT_270
#endif
#endif
#endif // ULTRA_LCD
//
// SD Support
//
//#define USB_SD_DISABLED // Disable host access to SD card as mass storage device through USB
//#define USB_SD_ONBOARD // Enable host access to SD card as mass storage device through USB
//#define LPC_SD_LCD // Marlin uses the SD drive attached to the LCD
2018-10-19 15:27:07 -05:00
#define LPC_SD_ONBOARD // Marlin uses the SD drive on the control board. There is no SD detect pin
// for the onboard card. Init card from LCD menu or send M21 whenever printer
// is powered on to enable SD access.
#if ENABLED(LPC_SD_LCD)
#define SCK_PIN P0_15
#define MISO_PIN P0_17
#define MOSI_PIN P0_18
#define SS_PIN P1_23 // Chip select for SD card used by Marlin
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
#elif ENABLED(LPC_SD_ONBOARD)
#if ENABLED(USB_SD_ONBOARD)
// When sharing the SD card with a PC we want the menu options to
// mount/unmount the card and refresh it. So we disable card detect.
#define SHARED_SD_CARD
#undef SD_DETECT_PIN // there is also no detect pin for the onboard card
#endif
#define SCK_PIN P0_07
#define MISO_PIN P0_08
#define MOSI_PIN P0_09
#define SS_PIN P0_06 // Chip select for SD card used by Marlin
#define ONBOARD_SD_CS P0_06 // Chip select for "System" SD card
#endif